Merge branch 'net-phy-at803x-device-tree-binding'

Michael Walle says:

====================
net: phy: at803x device tree binding

Adds a device tree binding to configure the clock and the RGMII voltage.

Changes since v1:
 - rebased to latest net-next
 - renamed "Atheros" to "Qualcomm Atheros"
 - add a new patch to remove config_init() from AR9331

Changes since the RFC:
 - renamed the Kconfig entry to "Qualcomm Atheros.." and reordered the
   item
 - renamed the prefix from atheros to qca
 - use the correct name AR803x (instead of AT803x) in new files and
   dt-bindings.
 - listed the PHY maintainers in the new schema. Hopefully, thats ok.
 - fixed a typo in the bindings schema
 - run dtb_checks and dt_binding_check and fixed the schema
 - dropped the rgmii-io-1v8 property; instead provide two regulators vddh
   and vddio, add one consumer vddio-supply
 - fix the clock settings for the AR8030/AR8035
 - only the AR8031 supports chaning the LDO and the PLL mode in software.
   Check if we have the correct PHY.
 - new patch to mention the AR8033 which is the same as the AR8031 just
   without PTP support
 - new patch which corrects any displayed PHY names and comments. Be
   consistent.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/qca,ar803x.yaml

@@ -0,0 +1,111 @@
+# SPDX-License-Identifier: GPL-2.0+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/qca,ar803x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Atheros AR803x PHY
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+  - Florian Fainelli <f.fainelli@gmail.com>
+  - Heiner Kallweit <hkallweit1@gmail.com>
+
+description: |
+  Bindings for Qualcomm Atheros AR803x PHYs
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+properties:
+  qca,clk-out-frequency:
+    description: Clock output frequency in Hertz.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 25000000, 50000000, 62500000, 125000000 ]
+
+  qca,clk-out-strength:
+    description: Clock output driver strength.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - enum: [ 0, 1, 2 ]
+
+  qca,keep-pll-enabled:
+    description: |
+      If set, keep the PLL enabled even if there is no link. Useful if you
+      want to use the clock output without an ethernet link.
+
+      Only supported on the AR8031.
+    type: boolean
+
+  vddio-supply:
+    description: |
+      RGMII I/O voltage regulator (see regulator/regulator.yaml).
+
+      The PHY supports RGMII I/O voltages of 1.5V, 1.8V and 2.5V. You can
+      either connect this to the vddio-regulator (1.5V / 1.8V) or the
+      vddh-regulator (2.5V).
+
+      Only supported on the AR8031.
+
+  vddio-regulator:
+    type: object
+    description:
+      Initial data for the VDDIO regulator. Set this to 1.5V or 1.8V.
+    allOf:
+      - $ref: /schemas/regulator/regulator.yaml
+
+  vddh-regulator:
+    type: object
+    description:
+      Dummy subnode to model the external connection of the PHY VDDH
+      regulator to VDDIO.
+    allOf:
+      - $ref: /schemas/regulator/regulator.yaml
+
+
+examples:
+  - |
+    #include <dt-bindings/net/qca-ar803x.h>
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy-mode = "rgmii-id";
+
+        ethernet-phy@0 {
+            reg = <0>;
+
+            qca,clk-out-frequency = <125000000>;
+            qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+
+            vddio-supply = <&vddio>;
+
+            vddio: vddio-regulator {
+                regulator-min-microvolt = <1800000>;
+                regulator-max-microvolt = <1800000>;
+            };
+        };
+    };
+  - |
+    #include <dt-bindings/net/qca-ar803x.h>
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy-mode = "rgmii-id";
+
+        ethernet-phy@0 {
+            reg = <0>;
+
+            qca,clk-out-frequency = <50000000>;
+            qca,keep-pll-enabled;
+
+            vddio-supply = <&vddh>;
+
+            vddh: vddh-regulator {
+            };
+        };
+    };

MAINTAINERS

@@ -6155,10 +6155,12 @@ S:	Maintained
 F:	Documentation/ABI/testing/sysfs-class-net-phydev
 F:	Documentation/devicetree/bindings/net/ethernet-phy.yaml
 F:	Documentation/devicetree/bindings/net/mdio*
+F:	Documentation/devicetree/bindings/net/qca,ar803x.yaml
 F:	Documentation/networking/phy.rst
 F:	drivers/net/phy/
 F:	drivers/of/of_mdio.c
 F:	drivers/of/of_net.c
+F:	include/dt-bindings/net/qca-ar803x.h
 F:	include/linux/*mdio*.h
 F:	include/linux/of_net.h
 F:	include/linux/phy.h

drivers/net/phy/Kconfig

@@ -282,11 +282,6 @@ config AX88796B_PHY
 	  Currently supports the Asix Electronics PHY found in the X-Surf 100
 	  AX88796B package.
 
-config AT803X_PHY
-	tristate "AT803X PHYs"
-	---help---
-	  Currently supports the AT8030 and AT8035 model
-
 config BCM63XX_PHY
 	tristate "Broadcom 63xx SOCs internal PHY"
 	depends on BCM63XX || COMPILE_TEST
@@ -444,6 +439,11 @@ config NXP_TJA11XX_PHY
 	---help---
 	  Currently supports the NXP TJA1100 and TJA1101 PHY.
 
+config AT803X_PHY
+	tristate "Qualcomm Atheros AR803X PHYs"
+	help
+	  Currently supports the AR8030, AR8031, AR8033 and AR8035 model
+
 config QSEMI_PHY
 	tristate "Quality Semiconductor PHYs"
 	---help---

drivers/net/phy/at803x.c

@@ -2,7 +2,7 @@
 /*
  * drivers/net/phy/at803x.c
  *
- * Driver for Atheros 803x PHY
+ * Driver for Qualcomm Atheros AR803x PHY
  *
  * Author: Matus Ujhelyi <ujhelyi.m@gmail.com>
  */
@@ -13,7 +13,12 @@
 #include <linux/netdevice.h>
 #include <linux/etherdevice.h>
 #include <linux/of_gpio.h>
+#include <linux/bitfield.h>
 #include <linux/gpio/consumer.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/consumer.h>
+#include <dt-bindings/net/qca-ar803x.h>
 
 #define AT803X_SPECIFIC_STATUS			0x11
 #define AT803X_SS_SPEED_MASK			(3 << 14)
@@ -62,16 +67,62 @@
 #define AT803X_DEBUG_REG_5			0x05
 #define AT803X_DEBUG_TX_CLK_DLY_EN		BIT(8)
 
+#define AT803X_DEBUG_REG_1F			0x1F
+#define AT803X_DEBUG_PLL_ON			BIT(2)
+#define AT803X_DEBUG_RGMII_1V8			BIT(3)
+
+/* AT803x supports either the XTAL input pad, an internal PLL or the
+ * DSP as clock reference for the clock output pad. The XTAL reference
+ * is only used for 25 MHz output, all other frequencies need the PLL.
+ * The DSP as a clock reference is used in synchronous ethernet
+ * applications.
+ *
+ * By default the PLL is only enabled if there is a link. Otherwise
+ * the PHY will go into low power state and disabled the PLL. You can
+ * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always
+ * enabled.
+ */
+#define AT803X_MMD7_CLK25M			0x8016
+#define AT803X_CLK_OUT_MASK			GENMASK(4, 2)
+#define AT803X_CLK_OUT_25MHZ_XTAL		0
+#define AT803X_CLK_OUT_25MHZ_DSP		1
+#define AT803X_CLK_OUT_50MHZ_PLL		2
+#define AT803X_CLK_OUT_50MHZ_DSP		3
+#define AT803X_CLK_OUT_62_5MHZ_PLL		4
+#define AT803X_CLK_OUT_62_5MHZ_DSP		5
+#define AT803X_CLK_OUT_125MHZ_PLL		6
+#define AT803X_CLK_OUT_125MHZ_DSP		7
+
+/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask
+ * but doesn't support choosing between XTAL/PLL and DSP.
+ */
+#define AT8035_CLK_OUT_MASK			GENMASK(4, 3)
+
+#define AT803X_CLK_OUT_STRENGTH_MASK		GENMASK(8, 7)
+#define AT803X_CLK_OUT_STRENGTH_FULL		0
+#define AT803X_CLK_OUT_STRENGTH_HALF		1
+#define AT803X_CLK_OUT_STRENGTH_QUARTER		2
+
 #define ATH9331_PHY_ID 0x004dd041
 #define ATH8030_PHY_ID 0x004dd076
 #define ATH8031_PHY_ID 0x004dd074
 #define ATH8035_PHY_ID 0x004dd072
 #define AT803X_PHY_ID_MASK			0xffffffef
 
-MODULE_DESCRIPTION("Atheros 803x PHY driver");
+MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver");
 MODULE_AUTHOR("Matus Ujhelyi");
 MODULE_LICENSE("GPL");
 
+struct at803x_priv {
+	int flags;
+#define AT803X_KEEP_PLL_ENABLED	BIT(0)	/* don't turn off internal PLL */
+	u16 clk_25m_reg;
+	u16 clk_25m_mask;
+	struct regulator_dev *vddio_rdev;
+	struct regulator_dev *vddh_rdev;
+	struct regulator *vddio;
+};
+
 struct at803x_context {
 	u16 bmcr;
 	u16 advertise;
@@ -237,6 +288,240 @@ static int at803x_resume(struct phy_device *phydev)
 	return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0);
 }
 
+static int at803x_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev,
+					    unsigned int selector)
+{
+	struct phy_device *phydev = rdev_get_drvdata(rdev);
+
+	if (selector)
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     0, AT803X_DEBUG_RGMII_1V8);
+	else
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     AT803X_DEBUG_RGMII_1V8, 0);
+}
+
+static int at803x_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev)
+{
+	struct phy_device *phydev = rdev_get_drvdata(rdev);
+	int val;
+
+	val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F);
+	if (val < 0)
+		return val;
+
+	return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0;
+}
+
+static struct regulator_ops vddio_regulator_ops = {
+	.list_voltage = regulator_list_voltage_table,
+	.set_voltage_sel = at803x_rgmii_reg_set_voltage_sel,
+	.get_voltage_sel = at803x_rgmii_reg_get_voltage_sel,
+};
+
+static const unsigned int vddio_voltage_table[] = {
+	1500000,
+	1800000,
+};
+
+static const struct regulator_desc vddio_desc = {
+	.name = "vddio",
+	.of_match = of_match_ptr("vddio-regulator"),
+	.n_voltages = ARRAY_SIZE(vddio_voltage_table),
+	.volt_table = vddio_voltage_table,
+	.ops = &vddio_regulator_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+};
+
+static struct regulator_ops vddh_regulator_ops = {
+};
+
+static const struct regulator_desc vddh_desc = {
+	.name = "vddh",
+	.of_match = of_match_ptr("vddh-regulator"),
+	.n_voltages = 1,
+	.fixed_uV = 2500000,
+	.ops = &vddh_regulator_ops,
+	.type = REGULATOR_VOLTAGE,
+	.owner = THIS_MODULE,
+};
+
+static int at8031_register_regulators(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	struct device *dev = &phydev->mdio.dev;
+	struct regulator_config config = { };
+
+	config.dev = dev;
+	config.driver_data = phydev;
+
+	priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config);
+	if (IS_ERR(priv->vddio_rdev)) {
+		phydev_err(phydev, "failed to register VDDIO regulator\n");
+		return PTR_ERR(priv->vddio_rdev);
+	}
+
+	priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config);
+	if (IS_ERR(priv->vddh_rdev)) {
+		phydev_err(phydev, "failed to register VDDH regulator\n");
+		return PTR_ERR(priv->vddh_rdev);
+	}
+
+	return 0;
+}
+
+static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id)
+{
+	return (phydev->phy_id & phydev->drv->phy_id_mask)
+		== (phy_id & phydev->drv->phy_id_mask);
+}
+
+static int at803x_parse_dt(struct phy_device *phydev)
+{
+	struct device_node *node = phydev->mdio.dev.of_node;
+	struct at803x_priv *priv = phydev->priv;
+	unsigned int sel, mask;
+	u32 freq, strength;
+	int ret;
+
+	if (!IS_ENABLED(CONFIG_OF_MDIO))
+		return 0;
+
+	ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq);
+	if (!ret) {
+		mask = AT803X_CLK_OUT_MASK;
+		switch (freq) {
+		case 25000000:
+			sel = AT803X_CLK_OUT_25MHZ_XTAL;
+			break;
+		case 50000000:
+			sel = AT803X_CLK_OUT_50MHZ_PLL;
+			break;
+		case 62500000:
+			sel = AT803X_CLK_OUT_62_5MHZ_PLL;
+			break;
+		case 125000000:
+			sel = AT803X_CLK_OUT_125MHZ_PLL;
+			break;
+		default:
+			phydev_err(phydev, "invalid qca,clk-out-frequency\n");
+			return -EINVAL;
+		}
+
+		priv->clk_25m_reg |= FIELD_PREP(mask, sel);
+		priv->clk_25m_mask |= mask;
+
+		/* Fixup for the AR8030/AR8035. This chip has another mask and
+		 * doesn't support the DSP reference. Eg. the lowest bit of the
+		 * mask. The upper two bits select the same frequencies. Mask
+		 * the lowest bit here.
+		 *
+		 * Warning:
+		 *   There was no datasheet for the AR8030 available so this is
+		 *   just a guess. But the AR8035 is listed as pin compatible
+		 *   to the AR8030 so there might be a good chance it works on
+		 *   the AR8030 too.
+		 */
+		if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) ||
+		    at803x_match_phy_id(phydev, ATH8035_PHY_ID)) {
+			priv->clk_25m_reg &= ~AT8035_CLK_OUT_MASK;
+			priv->clk_25m_mask &= ~AT8035_CLK_OUT_MASK;
+		}
+	}
+
+	ret = of_property_read_u32(node, "qca,clk-out-strength", &strength);
+	if (!ret) {
+		priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK;
+		switch (strength) {
+		case AR803X_STRENGTH_FULL:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL;
+			break;
+		case AR803X_STRENGTH_HALF:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF;
+			break;
+		case AR803X_STRENGTH_QUARTER:
+			priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER;
+			break;
+		default:
+			phydev_err(phydev, "invalid qca,clk-out-strength\n");
+			return -EINVAL;
+		}
+	}
+
+	/* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping
+	 * options.
+	 */
+	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+		if (of_property_read_bool(node, "qca,keep-pll-enabled"))
+			priv->flags |= AT803X_KEEP_PLL_ENABLED;
+
+		ret = at8031_register_regulators(phydev);
+		if (ret < 0)
+			return ret;
+
+		priv->vddio = devm_regulator_get_optional(&phydev->mdio.dev,
+							  "vddio");
+		if (IS_ERR(priv->vddio)) {
+			phydev_err(phydev, "failed to get VDDIO regulator\n");
+			return PTR_ERR(priv->vddio);
+		}
+
+		ret = regulator_enable(priv->vddio);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int at803x_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct at803x_priv *priv;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	phydev->priv = priv;
+
+	return at803x_parse_dt(phydev);
+}
+
+static int at803x_clk_out_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+	int val;
+
+	if (!priv->clk_25m_mask)
+		return 0;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M);
+	if (val < 0)
+		return val;
+
+	val &= ~priv->clk_25m_mask;
+	val |= priv->clk_25m_reg;
+
+	return phy_write_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M, val);
+}
+
+static int at8031_pll_config(struct phy_device *phydev)
+{
+	struct at803x_priv *priv = phydev->priv;
+
+	/* The default after hardware reset is PLL OFF. After a soft reset, the
+	 * values are retained.
+	 */
+	if (priv->flags & AT803X_KEEP_PLL_ENABLED)
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     0, AT803X_DEBUG_PLL_ON);
+	else
+		return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+					     AT803X_DEBUG_PLL_ON, 0);
+}
+
 static int at803x_config_init(struct phy_device *phydev)
 {
 	int ret;
@@ -259,8 +544,20 @@ static int at803x_config_init(struct phy_device *phydev)
 		ret = at803x_enable_tx_delay(phydev);
 	else
 		ret = at803x_disable_tx_delay(phydev);
+	if (ret < 0)
+		return ret;
 
-	return ret;
+	ret = at803x_clk_out_config(phydev);
+	if (ret < 0)
+		return ret;
+
+	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+		ret = at8031_pll_config(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
 }
 
 static int at803x_ack_interrupt(struct phy_device *phydev)
@@ -409,10 +706,11 @@ static int at803x_read_status(struct phy_device *phydev)
 
 static struct phy_driver at803x_driver[] = {
 {
-	/* ATHEROS 8035 */
+	/* Qualcomm Atheros AR8035 */
 	.phy_id			= ATH8035_PHY_ID,
-	.name			= "Atheros 8035 ethernet",
+	.name			= "Qualcomm Atheros AR8035",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
+	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.set_wol		= at803x_set_wol,
 	.get_wol		= at803x_get_wol,
@@ -423,10 +721,11 @@ static struct phy_driver at803x_driver[] = {
 	.ack_interrupt		= at803x_ack_interrupt,
 	.config_intr		= at803x_config_intr,
 }, {
-	/* ATHEROS 8030 */
+	/* Qualcomm Atheros AR8030 */
 	.phy_id			= ATH8030_PHY_ID,
-	.name			= "Atheros 8030 ethernet",
+	.name			= "Qualcomm Atheros AR8030",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
+	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.link_change_notify	= at803x_link_change_notify,
 	.set_wol		= at803x_set_wol,
@@ -437,10 +736,11 @@ static struct phy_driver at803x_driver[] = {
 	.ack_interrupt		= at803x_ack_interrupt,
 	.config_intr		= at803x_config_intr,
 }, {
-	/* ATHEROS 8031 */
+	/* Qualcomm Atheros AR8031/AR8033 */
 	.phy_id			= ATH8031_PHY_ID,
-	.name			= "Atheros 8031 ethernet",
+	.name			= "Qualcomm Atheros AR8031/AR8033",
 	.phy_id_mask		= AT803X_PHY_ID_MASK,
+	.probe			= at803x_probe,
 	.config_init		= at803x_config_init,
 	.set_wol		= at803x_set_wol,
 	.get_wol		= at803x_get_wol,
@@ -454,8 +754,7 @@ static struct phy_driver at803x_driver[] = {
 }, {
 	/* ATHEROS AR9331 */
 	PHY_ID_MATCH_EXACT(ATH9331_PHY_ID),
-	.name			= "Atheros AR9331 built-in PHY",
-	.config_init		= at803x_config_init,
+	.name			= "Qualcomm Atheros AR9331 built-in PHY",
 	.suspend		= at803x_suspend,
 	.resume			= at803x_resume,
 	/* PHY_BASIC_FEATURES */

include/dt-bindings/net/qca-ar803x.h

@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Device Tree constants for the Qualcomm Atheros AR803x PHYs
+ */
+
+#ifndef _DT_BINDINGS_QCA_AR803X_H
+#define _DT_BINDINGS_QCA_AR803X_H
+
+#define AR803X_STRENGTH_FULL		0
+#define AR803X_STRENGTH_HALF		1
+#define AR803X_STRENGTH_QUARTER		2
+
+#endif