linux_dsm_epyc7002/drivers/net/ethernet/mellanox/mlxsw/spectrum.c

3446 lines
92 KiB
C
Raw Normal View History

/*
* drivers/net/ethernet/mellanox/mlxsw/spectrum.c
* Copyright (c) 2015 Mellanox Technologies. All rights reserved.
* Copyright (c) 2015 Jiri Pirko <jiri@mellanox.com>
* Copyright (c) 2015 Ido Schimmel <idosch@mellanox.com>
* Copyright (c) 2015 Elad Raz <eladr@mellanox.com>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the names of the copyright holders nor the names of its
* contributors may be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/ethtool.h>
#include <linux/slab.h>
#include <linux/device.h>
#include <linux/skbuff.h>
#include <linux/if_vlan.h>
#include <linux/if_bridge.h>
#include <linux/workqueue.h>
#include <linux/jiffies.h>
#include <linux/bitops.h>
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
#include <linux/list.h>
#include <linux/dcbnl.h>
#include <net/devlink.h>
#include <net/switchdev.h>
#include <generated/utsrelease.h>
#include "spectrum.h"
#include "core.h"
#include "reg.h"
#include "port.h"
#include "trap.h"
#include "txheader.h"
static const char mlxsw_sp_driver_name[] = "mlxsw_spectrum";
static const char mlxsw_sp_driver_version[] = "1.0";
/* tx_hdr_version
* Tx header version.
* Must be set to 1.
*/
MLXSW_ITEM32(tx, hdr, version, 0x00, 28, 4);
/* tx_hdr_ctl
* Packet control type.
* 0 - Ethernet control (e.g. EMADs, LACP)
* 1 - Ethernet data
*/
MLXSW_ITEM32(tx, hdr, ctl, 0x00, 26, 2);
/* tx_hdr_proto
* Packet protocol type. Must be set to 1 (Ethernet).
*/
MLXSW_ITEM32(tx, hdr, proto, 0x00, 21, 3);
/* tx_hdr_rx_is_router
* Packet is sent from the router. Valid for data packets only.
*/
MLXSW_ITEM32(tx, hdr, rx_is_router, 0x00, 19, 1);
/* tx_hdr_fid_valid
* Indicates if the 'fid' field is valid and should be used for
* forwarding lookup. Valid for data packets only.
*/
MLXSW_ITEM32(tx, hdr, fid_valid, 0x00, 16, 1);
/* tx_hdr_swid
* Switch partition ID. Must be set to 0.
*/
MLXSW_ITEM32(tx, hdr, swid, 0x00, 12, 3);
/* tx_hdr_control_tclass
* Indicates if the packet should use the control TClass and not one
* of the data TClasses.
*/
MLXSW_ITEM32(tx, hdr, control_tclass, 0x00, 6, 1);
/* tx_hdr_etclass
* Egress TClass to be used on the egress device on the egress port.
*/
MLXSW_ITEM32(tx, hdr, etclass, 0x00, 0, 4);
/* tx_hdr_port_mid
* Destination local port for unicast packets.
* Destination multicast ID for multicast packets.
*
* Control packets are directed to a specific egress port, while data
* packets are transmitted through the CPU port (0) into the switch partition,
* where forwarding rules are applied.
*/
MLXSW_ITEM32(tx, hdr, port_mid, 0x04, 16, 16);
/* tx_hdr_fid
* Forwarding ID used for L2 forwarding lookup. Valid only if 'fid_valid' is
* set, otherwise calculated based on the packet's VID using VID to FID mapping.
* Valid for data packets only.
*/
MLXSW_ITEM32(tx, hdr, fid, 0x08, 0, 16);
/* tx_hdr_type
* 0 - Data packets
* 6 - Control packets
*/
MLXSW_ITEM32(tx, hdr, type, 0x0C, 0, 4);
static void mlxsw_sp_txhdr_construct(struct sk_buff *skb,
const struct mlxsw_tx_info *tx_info)
{
char *txhdr = skb_push(skb, MLXSW_TXHDR_LEN);
memset(txhdr, 0, MLXSW_TXHDR_LEN);
mlxsw_tx_hdr_version_set(txhdr, MLXSW_TXHDR_VERSION_1);
mlxsw_tx_hdr_ctl_set(txhdr, MLXSW_TXHDR_ETH_CTL);
mlxsw_tx_hdr_proto_set(txhdr, MLXSW_TXHDR_PROTO_ETH);
mlxsw_tx_hdr_swid_set(txhdr, 0);
mlxsw_tx_hdr_control_tclass_set(txhdr, 1);
mlxsw_tx_hdr_port_mid_set(txhdr, tx_info->local_port);
mlxsw_tx_hdr_type_set(txhdr, MLXSW_TXHDR_TYPE_CONTROL);
}
static int mlxsw_sp_base_mac_get(struct mlxsw_sp *mlxsw_sp)
{
char spad_pl[MLXSW_REG_SPAD_LEN];
int err;
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(spad), spad_pl);
if (err)
return err;
mlxsw_reg_spad_base_mac_memcpy_from(spad_pl, mlxsw_sp->base_mac);
return 0;
}
static int mlxsw_sp_port_admin_status_set(struct mlxsw_sp_port *mlxsw_sp_port,
bool is_up)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char paos_pl[MLXSW_REG_PAOS_LEN];
mlxsw_reg_paos_pack(paos_pl, mlxsw_sp_port->local_port,
is_up ? MLXSW_PORT_ADMIN_STATUS_UP :
MLXSW_PORT_ADMIN_STATUS_DOWN);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(paos), paos_pl);
}
static int mlxsw_sp_port_oper_status_get(struct mlxsw_sp_port *mlxsw_sp_port,
bool *p_is_up)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char paos_pl[MLXSW_REG_PAOS_LEN];
u8 oper_status;
int err;
mlxsw_reg_paos_pack(paos_pl, mlxsw_sp_port->local_port, 0);
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(paos), paos_pl);
if (err)
return err;
oper_status = mlxsw_reg_paos_oper_status_get(paos_pl);
*p_is_up = oper_status == MLXSW_PORT_ADMIN_STATUS_UP ? true : false;
return 0;
}
static int mlxsw_sp_port_dev_addr_set(struct mlxsw_sp_port *mlxsw_sp_port,
unsigned char *addr)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char ppad_pl[MLXSW_REG_PPAD_LEN];
mlxsw_reg_ppad_pack(ppad_pl, true, mlxsw_sp_port->local_port);
mlxsw_reg_ppad_mac_memcpy_to(ppad_pl, addr);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(ppad), ppad_pl);
}
static int mlxsw_sp_port_dev_addr_init(struct mlxsw_sp_port *mlxsw_sp_port)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
unsigned char *addr = mlxsw_sp_port->dev->dev_addr;
ether_addr_copy(addr, mlxsw_sp->base_mac);
addr[ETH_ALEN - 1] += mlxsw_sp_port->local_port;
return mlxsw_sp_port_dev_addr_set(mlxsw_sp_port, addr);
}
static int mlxsw_sp_port_stp_state_set(struct mlxsw_sp_port *mlxsw_sp_port,
u16 vid, enum mlxsw_reg_spms_state state)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char *spms_pl;
int err;
spms_pl = kmalloc(MLXSW_REG_SPMS_LEN, GFP_KERNEL);
if (!spms_pl)
return -ENOMEM;
mlxsw_reg_spms_pack(spms_pl, mlxsw_sp_port->local_port);
mlxsw_reg_spms_vid_pack(spms_pl, vid, state);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(spms), spms_pl);
kfree(spms_pl);
return err;
}
static int mlxsw_sp_port_mtu_set(struct mlxsw_sp_port *mlxsw_sp_port, u16 mtu)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char pmtu_pl[MLXSW_REG_PMTU_LEN];
int max_mtu;
int err;
mtu += MLXSW_TXHDR_LEN + ETH_HLEN;
mlxsw_reg_pmtu_pack(pmtu_pl, mlxsw_sp_port->local_port, 0);
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(pmtu), pmtu_pl);
if (err)
return err;
max_mtu = mlxsw_reg_pmtu_max_mtu_get(pmtu_pl);
if (mtu > max_mtu)
return -EINVAL;
mlxsw_reg_pmtu_pack(pmtu_pl, mlxsw_sp_port->local_port, mtu);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(pmtu), pmtu_pl);
}
static int mlxsw_sp_port_swid_set(struct mlxsw_sp_port *mlxsw_sp_port, u8 swid)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char pspa_pl[MLXSW_REG_PSPA_LEN];
mlxsw_reg_pspa_pack(pspa_pl, swid, mlxsw_sp_port->local_port);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(pspa), pspa_pl);
}
static int mlxsw_sp_port_vp_mode_set(struct mlxsw_sp_port *mlxsw_sp_port,
bool enable)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char svpe_pl[MLXSW_REG_SVPE_LEN];
mlxsw_reg_svpe_pack(svpe_pl, mlxsw_sp_port->local_port, enable);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(svpe), svpe_pl);
}
int mlxsw_sp_port_vid_to_fid_set(struct mlxsw_sp_port *mlxsw_sp_port,
enum mlxsw_reg_svfa_mt mt, bool valid, u16 fid,
u16 vid)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char svfa_pl[MLXSW_REG_SVFA_LEN];
mlxsw_reg_svfa_pack(svfa_pl, mlxsw_sp_port->local_port, mt, valid,
fid, vid);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(svfa), svfa_pl);
}
static int mlxsw_sp_port_vid_learning_set(struct mlxsw_sp_port *mlxsw_sp_port,
u16 vid, bool learn_enable)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char *spvmlr_pl;
int err;
spvmlr_pl = kmalloc(MLXSW_REG_SPVMLR_LEN, GFP_KERNEL);
if (!spvmlr_pl)
return -ENOMEM;
mlxsw_reg_spvmlr_pack(spvmlr_pl, mlxsw_sp_port->local_port, vid, vid,
learn_enable);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(spvmlr), spvmlr_pl);
kfree(spvmlr_pl);
return err;
}
static int
mlxsw_sp_port_system_port_mapping_set(struct mlxsw_sp_port *mlxsw_sp_port)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char sspr_pl[MLXSW_REG_SSPR_LEN];
mlxsw_reg_sspr_pack(sspr_pl, mlxsw_sp_port->local_port);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sspr), sspr_pl);
}
static int __mlxsw_sp_port_module_info_get(struct mlxsw_sp *mlxsw_sp,
u8 local_port, u8 *p_module,
u8 *p_width, u8 *p_lane)
{
char pmlp_pl[MLXSW_REG_PMLP_LEN];
int err;
mlxsw_reg_pmlp_pack(pmlp_pl, local_port);
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(pmlp), pmlp_pl);
if (err)
return err;
*p_module = mlxsw_reg_pmlp_module_get(pmlp_pl, 0);
*p_width = mlxsw_reg_pmlp_width_get(pmlp_pl);
*p_lane = mlxsw_reg_pmlp_tx_lane_get(pmlp_pl, 0);
return 0;
}
static int mlxsw_sp_port_module_info_get(struct mlxsw_sp *mlxsw_sp,
u8 local_port, u8 *p_module,
u8 *p_width)
{
u8 lane;
return __mlxsw_sp_port_module_info_get(mlxsw_sp, local_port, p_module,
p_width, &lane);
}
static int mlxsw_sp_port_module_map(struct mlxsw_sp *mlxsw_sp, u8 local_port,
u8 module, u8 width, u8 lane)
{
char pmlp_pl[MLXSW_REG_PMLP_LEN];
int i;
mlxsw_reg_pmlp_pack(pmlp_pl, local_port);
mlxsw_reg_pmlp_width_set(pmlp_pl, width);
for (i = 0; i < width; i++) {
mlxsw_reg_pmlp_module_set(pmlp_pl, i, module);
mlxsw_reg_pmlp_tx_lane_set(pmlp_pl, i, lane + i); /* Rx & Tx */
}
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(pmlp), pmlp_pl);
}
static int mlxsw_sp_port_module_unmap(struct mlxsw_sp *mlxsw_sp, u8 local_port)
{
char pmlp_pl[MLXSW_REG_PMLP_LEN];
mlxsw_reg_pmlp_pack(pmlp_pl, local_port);
mlxsw_reg_pmlp_width_set(pmlp_pl, 0);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(pmlp), pmlp_pl);
}
static int mlxsw_sp_port_open(struct net_device *dev)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
int err;
err = mlxsw_sp_port_admin_status_set(mlxsw_sp_port, true);
if (err)
return err;
netif_start_queue(dev);
return 0;
}
static int mlxsw_sp_port_stop(struct net_device *dev)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
netif_stop_queue(dev);
return mlxsw_sp_port_admin_status_set(mlxsw_sp_port, false);
}
static netdev_tx_t mlxsw_sp_port_xmit(struct sk_buff *skb,
struct net_device *dev)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
struct mlxsw_sp_port_pcpu_stats *pcpu_stats;
const struct mlxsw_tx_info tx_info = {
.local_port = mlxsw_sp_port->local_port,
.is_emad = false,
};
u64 len;
int err;
if (mlxsw_core_skb_transmit_busy(mlxsw_sp, &tx_info))
return NETDEV_TX_BUSY;
if (unlikely(skb_headroom(skb) < MLXSW_TXHDR_LEN)) {
struct sk_buff *skb_orig = skb;
skb = skb_realloc_headroom(skb, MLXSW_TXHDR_LEN);
if (!skb) {
this_cpu_inc(mlxsw_sp_port->pcpu_stats->tx_dropped);
dev_kfree_skb_any(skb_orig);
return NETDEV_TX_OK;
}
}
if (eth_skb_pad(skb)) {
this_cpu_inc(mlxsw_sp_port->pcpu_stats->tx_dropped);
return NETDEV_TX_OK;
}
mlxsw_sp_txhdr_construct(skb, &tx_info);
len = skb->len;
/* Due to a race we might fail here because of a full queue. In that
* unlikely case we simply drop the packet.
*/
err = mlxsw_core_skb_transmit(mlxsw_sp, skb, &tx_info);
if (!err) {
pcpu_stats = this_cpu_ptr(mlxsw_sp_port->pcpu_stats);
u64_stats_update_begin(&pcpu_stats->syncp);
pcpu_stats->tx_packets++;
pcpu_stats->tx_bytes += len;
u64_stats_update_end(&pcpu_stats->syncp);
} else {
this_cpu_inc(mlxsw_sp_port->pcpu_stats->tx_dropped);
dev_kfree_skb_any(skb);
}
return NETDEV_TX_OK;
}
static void mlxsw_sp_set_rx_mode(struct net_device *dev)
{
}
static int mlxsw_sp_port_set_mac_address(struct net_device *dev, void *p)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct sockaddr *addr = p;
int err;
if (!is_valid_ether_addr(addr->sa_data))
return -EADDRNOTAVAIL;
err = mlxsw_sp_port_dev_addr_set(mlxsw_sp_port, addr->sa_data);
if (err)
return err;
memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
return 0;
}
mlxsw: spectrum: Correctly configure headroom size When packets ingress the switch they are assigned a switch priority and directed to the corresponding priority group (PG) buffer in the port's headroom buffer. Since we now map all switch priorities to priority group 0 (PG0) by default, there is no need to allocate the other priority groups during initialization. The only exception is PG9, which is used for control traffic. At minimum, the PG should be able to store the currently classified packet (pipeline latency isn't 0) and also the packets arriving during the classification time. However, an incoming packet will not be buffered if there is no available MTU-sized buffer space for storing it. The buffer needed to accommodate for pipeline latency is variable and needs to take into account both the current link speed and current latency of the pipeline, which is time-dependent. Testing showed that setting the PG's size to twice the current MTU is optimal. Since PG9 is used strictly for control packets and not subject to flow control, we are not going to resize it according to user configuration, so we simply set it according to worst case scenario, which is twice the maximum MTU. In any case, later patches in the series will allow a user to direct lossless flows to other PGs than PG0 and set their size to accommodate for round-trip propagation delay. The above change also requires us to resize the PG buffer whenever the port's MTU is changed. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-06 22:10:03 +07:00
static int mlxsw_sp_port_headroom_set(struct mlxsw_sp_port *mlxsw_sp_port,
int mtu)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
u16 pg_size = 2 * MLXSW_SP_BYTES_TO_CELLS(mtu);
char pbmc_pl[MLXSW_REG_PBMC_LEN];
int err;
mlxsw_reg_pbmc_pack(pbmc_pl, mlxsw_sp_port->local_port, 0, 0);
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(pbmc), pbmc_pl);
if (err)
return err;
mlxsw_reg_pbmc_lossy_buffer_pack(pbmc_pl, 0, pg_size);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(pbmc), pbmc_pl);
}
static int mlxsw_sp_port_change_mtu(struct net_device *dev, int mtu)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
int err;
mlxsw: spectrum: Correctly configure headroom size When packets ingress the switch they are assigned a switch priority and directed to the corresponding priority group (PG) buffer in the port's headroom buffer. Since we now map all switch priorities to priority group 0 (PG0) by default, there is no need to allocate the other priority groups during initialization. The only exception is PG9, which is used for control traffic. At minimum, the PG should be able to store the currently classified packet (pipeline latency isn't 0) and also the packets arriving during the classification time. However, an incoming packet will not be buffered if there is no available MTU-sized buffer space for storing it. The buffer needed to accommodate for pipeline latency is variable and needs to take into account both the current link speed and current latency of the pipeline, which is time-dependent. Testing showed that setting the PG's size to twice the current MTU is optimal. Since PG9 is used strictly for control packets and not subject to flow control, we are not going to resize it according to user configuration, so we simply set it according to worst case scenario, which is twice the maximum MTU. In any case, later patches in the series will allow a user to direct lossless flows to other PGs than PG0 and set their size to accommodate for round-trip propagation delay. The above change also requires us to resize the PG buffer whenever the port's MTU is changed. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-06 22:10:03 +07:00
err = mlxsw_sp_port_headroom_set(mlxsw_sp_port, mtu);
if (err)
return err;
mlxsw: spectrum: Correctly configure headroom size When packets ingress the switch they are assigned a switch priority and directed to the corresponding priority group (PG) buffer in the port's headroom buffer. Since we now map all switch priorities to priority group 0 (PG0) by default, there is no need to allocate the other priority groups during initialization. The only exception is PG9, which is used for control traffic. At minimum, the PG should be able to store the currently classified packet (pipeline latency isn't 0) and also the packets arriving during the classification time. However, an incoming packet will not be buffered if there is no available MTU-sized buffer space for storing it. The buffer needed to accommodate for pipeline latency is variable and needs to take into account both the current link speed and current latency of the pipeline, which is time-dependent. Testing showed that setting the PG's size to twice the current MTU is optimal. Since PG9 is used strictly for control packets and not subject to flow control, we are not going to resize it according to user configuration, so we simply set it according to worst case scenario, which is twice the maximum MTU. In any case, later patches in the series will allow a user to direct lossless flows to other PGs than PG0 and set their size to accommodate for round-trip propagation delay. The above change also requires us to resize the PG buffer whenever the port's MTU is changed. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-06 22:10:03 +07:00
err = mlxsw_sp_port_mtu_set(mlxsw_sp_port, mtu);
if (err)
goto err_port_mtu_set;
dev->mtu = mtu;
return 0;
mlxsw: spectrum: Correctly configure headroom size When packets ingress the switch they are assigned a switch priority and directed to the corresponding priority group (PG) buffer in the port's headroom buffer. Since we now map all switch priorities to priority group 0 (PG0) by default, there is no need to allocate the other priority groups during initialization. The only exception is PG9, which is used for control traffic. At minimum, the PG should be able to store the currently classified packet (pipeline latency isn't 0) and also the packets arriving during the classification time. However, an incoming packet will not be buffered if there is no available MTU-sized buffer space for storing it. The buffer needed to accommodate for pipeline latency is variable and needs to take into account both the current link speed and current latency of the pipeline, which is time-dependent. Testing showed that setting the PG's size to twice the current MTU is optimal. Since PG9 is used strictly for control packets and not subject to flow control, we are not going to resize it according to user configuration, so we simply set it according to worst case scenario, which is twice the maximum MTU. In any case, later patches in the series will allow a user to direct lossless flows to other PGs than PG0 and set their size to accommodate for round-trip propagation delay. The above change also requires us to resize the PG buffer whenever the port's MTU is changed. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-06 22:10:03 +07:00
err_port_mtu_set:
mlxsw_sp_port_headroom_set(mlxsw_sp_port, dev->mtu);
return err;
}
static struct rtnl_link_stats64 *
mlxsw_sp_port_get_stats64(struct net_device *dev,
struct rtnl_link_stats64 *stats)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp_port_pcpu_stats *p;
u64 rx_packets, rx_bytes, tx_packets, tx_bytes;
u32 tx_dropped = 0;
unsigned int start;
int i;
for_each_possible_cpu(i) {
p = per_cpu_ptr(mlxsw_sp_port->pcpu_stats, i);
do {
start = u64_stats_fetch_begin_irq(&p->syncp);
rx_packets = p->rx_packets;
rx_bytes = p->rx_bytes;
tx_packets = p->tx_packets;
tx_bytes = p->tx_bytes;
} while (u64_stats_fetch_retry_irq(&p->syncp, start));
stats->rx_packets += rx_packets;
stats->rx_bytes += rx_bytes;
stats->tx_packets += tx_packets;
stats->tx_bytes += tx_bytes;
/* tx_dropped is u32, updated without syncp protection. */
tx_dropped += p->tx_dropped;
}
stats->tx_dropped = tx_dropped;
return stats;
}
int mlxsw_sp_port_vlan_set(struct mlxsw_sp_port *mlxsw_sp_port, u16 vid_begin,
u16 vid_end, bool is_member, bool untagged)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char *spvm_pl;
int err;
spvm_pl = kmalloc(MLXSW_REG_SPVM_LEN, GFP_KERNEL);
if (!spvm_pl)
return -ENOMEM;
mlxsw_reg_spvm_pack(spvm_pl, mlxsw_sp_port->local_port, vid_begin,
vid_end, is_member, untagged);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(spvm), spvm_pl);
kfree(spvm_pl);
return err;
}
static int mlxsw_sp_port_vp_mode_trans(struct mlxsw_sp_port *mlxsw_sp_port)
{
enum mlxsw_reg_svfa_mt mt = MLXSW_REG_SVFA_MT_PORT_VID_TO_FID;
u16 vid, last_visited_vid;
int err;
for_each_set_bit(vid, mlxsw_sp_port->active_vlans, VLAN_N_VID) {
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_port, mt, true, vid,
vid);
if (err) {
last_visited_vid = vid;
goto err_port_vid_to_fid_set;
}
}
err = mlxsw_sp_port_vp_mode_set(mlxsw_sp_port, true);
if (err) {
last_visited_vid = VLAN_N_VID;
goto err_port_vid_to_fid_set;
}
return 0;
err_port_vid_to_fid_set:
for_each_set_bit(vid, mlxsw_sp_port->active_vlans, last_visited_vid)
mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_port, mt, false, vid,
vid);
return err;
}
static int mlxsw_sp_port_vlan_mode_trans(struct mlxsw_sp_port *mlxsw_sp_port)
{
enum mlxsw_reg_svfa_mt mt = MLXSW_REG_SVFA_MT_PORT_VID_TO_FID;
u16 vid;
int err;
err = mlxsw_sp_port_vp_mode_set(mlxsw_sp_port, false);
if (err)
return err;
for_each_set_bit(vid, mlxsw_sp_port->active_vlans, VLAN_N_VID) {
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_port, mt, false,
vid, vid);
if (err)
return err;
}
return 0;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
static struct mlxsw_sp_vfid *
mlxsw_sp_vfid_find(const struct mlxsw_sp *mlxsw_sp, u16 vid)
{
struct mlxsw_sp_vfid *vfid;
list_for_each_entry(vfid, &mlxsw_sp->port_vfids.list, list) {
if (vfid->vid == vid)
return vfid;
}
return NULL;
}
static u16 mlxsw_sp_avail_vfid_get(const struct mlxsw_sp *mlxsw_sp)
{
return find_first_zero_bit(mlxsw_sp->port_vfids.mapped,
MLXSW_SP_VFID_PORT_MAX);
}
static int __mlxsw_sp_vfid_create(struct mlxsw_sp *mlxsw_sp, u16 vfid)
{
u16 fid = mlxsw_sp_vfid_to_fid(vfid);
char sfmr_pl[MLXSW_REG_SFMR_LEN];
mlxsw_reg_sfmr_pack(sfmr_pl, MLXSW_REG_SFMR_OP_CREATE_FID, fid, 0);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sfmr), sfmr_pl);
}
static void __mlxsw_sp_vfid_destroy(struct mlxsw_sp *mlxsw_sp, u16 vfid)
{
u16 fid = mlxsw_sp_vfid_to_fid(vfid);
char sfmr_pl[MLXSW_REG_SFMR_LEN];
mlxsw_reg_sfmr_pack(sfmr_pl, MLXSW_REG_SFMR_OP_DESTROY_FID, fid, 0);
mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sfmr), sfmr_pl);
}
static struct mlxsw_sp_vfid *mlxsw_sp_vfid_create(struct mlxsw_sp *mlxsw_sp,
u16 vid)
{
struct device *dev = mlxsw_sp->bus_info->dev;
struct mlxsw_sp_vfid *vfid;
u16 n_vfid;
int err;
n_vfid = mlxsw_sp_avail_vfid_get(mlxsw_sp);
if (n_vfid == MLXSW_SP_VFID_PORT_MAX) {
dev_err(dev, "No available vFIDs\n");
return ERR_PTR(-ERANGE);
}
err = __mlxsw_sp_vfid_create(mlxsw_sp, n_vfid);
if (err) {
dev_err(dev, "Failed to create vFID=%d\n", n_vfid);
return ERR_PTR(err);
}
vfid = kzalloc(sizeof(*vfid), GFP_KERNEL);
if (!vfid)
goto err_allocate_vfid;
vfid->vfid = n_vfid;
vfid->vid = vid;
list_add(&vfid->list, &mlxsw_sp->port_vfids.list);
set_bit(n_vfid, mlxsw_sp->port_vfids.mapped);
return vfid;
err_allocate_vfid:
__mlxsw_sp_vfid_destroy(mlxsw_sp, n_vfid);
return ERR_PTR(-ENOMEM);
}
static void mlxsw_sp_vfid_destroy(struct mlxsw_sp *mlxsw_sp,
struct mlxsw_sp_vfid *vfid)
{
clear_bit(vfid->vfid, mlxsw_sp->port_vfids.mapped);
list_del(&vfid->list);
__mlxsw_sp_vfid_destroy(mlxsw_sp, vfid->vfid);
kfree(vfid);
}
static struct mlxsw_sp_port *
mlxsw_sp_port_vport_create(struct mlxsw_sp_port *mlxsw_sp_port,
struct mlxsw_sp_vfid *vfid)
{
struct mlxsw_sp_port *mlxsw_sp_vport;
mlxsw_sp_vport = kzalloc(sizeof(*mlxsw_sp_vport), GFP_KERNEL);
if (!mlxsw_sp_vport)
return NULL;
/* dev will be set correctly after the VLAN device is linked
* with the real device. In case of bridge SELF invocation, dev
* will remain as is.
*/
mlxsw_sp_vport->dev = mlxsw_sp_port->dev;
mlxsw_sp_vport->mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
mlxsw_sp_vport->local_port = mlxsw_sp_port->local_port;
mlxsw_sp_vport->stp_state = BR_STATE_FORWARDING;
mlxsw_sp_vport->lagged = mlxsw_sp_port->lagged;
mlxsw_sp_vport->lag_id = mlxsw_sp_port->lag_id;
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_vport->vport.vfid = vfid;
mlxsw_sp_vport->vport.vid = vfid->vid;
list_add(&mlxsw_sp_vport->vport.list, &mlxsw_sp_port->vports_list);
return mlxsw_sp_vport;
}
static void mlxsw_sp_port_vport_destroy(struct mlxsw_sp_port *mlxsw_sp_vport)
{
list_del(&mlxsw_sp_vport->vport.list);
kfree(mlxsw_sp_vport);
}
int mlxsw_sp_port_add_vid(struct net_device *dev, __be16 __always_unused proto,
u16 vid)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
struct mlxsw_sp_port *mlxsw_sp_vport;
struct mlxsw_sp_vfid *vfid;
int err;
/* VLAN 0 is added to HW filter when device goes up, but it is
* reserved in our case, so simply return.
*/
if (!vid)
return 0;
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
if (mlxsw_sp_port_vport_find(mlxsw_sp_port, vid)) {
netdev_warn(dev, "VID=%d already configured\n", vid);
return 0;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
vfid = mlxsw_sp_vfid_find(mlxsw_sp, vid);
if (!vfid) {
vfid = mlxsw_sp_vfid_create(mlxsw_sp, vid);
if (IS_ERR(vfid)) {
netdev_err(dev, "Failed to create vFID for VID=%d\n",
vid);
return PTR_ERR(vfid);
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_vport = mlxsw_sp_port_vport_create(mlxsw_sp_port, vfid);
if (!mlxsw_sp_vport) {
netdev_err(dev, "Failed to create vPort for VID=%d\n", vid);
err = -ENOMEM;
goto err_port_vport_create;
}
if (!vfid->nr_vports) {
err = mlxsw_sp_vport_flood_set(mlxsw_sp_vport, vfid->vfid,
true, false);
if (err) {
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
netdev_err(dev, "Failed to setup flooding for vFID=%d\n",
vfid->vfid);
goto err_vport_flood_set;
}
}
/* When adding the first VLAN interface on a bridged port we need to
* transition all the active 802.1Q bridge VLANs to use explicit
* {Port, VID} to FID mappings and set the port's mode to Virtual mode.
*/
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
if (list_is_singular(&mlxsw_sp_port->vports_list)) {
err = mlxsw_sp_port_vp_mode_trans(mlxsw_sp_port);
if (err) {
netdev_err(dev, "Failed to set to Virtual mode\n");
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
goto err_port_vp_mode_trans;
}
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID,
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
true,
mlxsw_sp_vfid_to_fid(vfid->vfid),
vid);
if (err) {
netdev_err(dev, "Failed to map {Port, VID=%d} to vFID=%d\n",
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
vid, vfid->vfid);
goto err_port_vid_to_fid_set;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err = mlxsw_sp_port_vid_learning_set(mlxsw_sp_vport, vid, false);
if (err) {
netdev_err(dev, "Failed to disable learning for VID=%d\n", vid);
goto err_port_vid_learning_set;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err = mlxsw_sp_port_vlan_set(mlxsw_sp_vport, vid, vid, true, false);
if (err) {
netdev_err(dev, "Failed to set VLAN membership for VID=%d\n",
vid);
goto err_port_add_vid;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err = mlxsw_sp_port_stp_state_set(mlxsw_sp_vport, vid,
MLXSW_REG_SPMS_STATE_FORWARDING);
if (err) {
netdev_err(dev, "Failed to set STP state for VID=%d\n", vid);
goto err_port_stp_state_set;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
vfid->nr_vports++;
return 0;
err_port_stp_state_set:
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_port_vlan_set(mlxsw_sp_vport, vid, vid, false, false);
err_port_add_vid:
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_port_vid_learning_set(mlxsw_sp_vport, vid, true);
err_port_vid_learning_set:
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID, false,
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_vfid_to_fid(vfid->vfid), vid);
err_port_vid_to_fid_set:
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
if (list_is_singular(&mlxsw_sp_port->vports_list))
mlxsw_sp_port_vlan_mode_trans(mlxsw_sp_port);
err_port_vp_mode_trans:
if (!vfid->nr_vports)
mlxsw_sp_vport_flood_set(mlxsw_sp_vport, vfid->vfid, false,
false);
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err_vport_flood_set:
mlxsw_sp_port_vport_destroy(mlxsw_sp_vport);
err_port_vport_create:
if (!vfid->nr_vports)
mlxsw_sp_vfid_destroy(mlxsw_sp, vfid);
return err;
}
int mlxsw_sp_port_kill_vid(struct net_device *dev,
__be16 __always_unused proto, u16 vid)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
struct mlxsw_sp_port *mlxsw_sp_vport;
struct mlxsw_sp_vfid *vfid;
int err;
/* VLAN 0 is removed from HW filter when device goes down, but
* it is reserved in our case, so simply return.
*/
if (!vid)
return 0;
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_vport = mlxsw_sp_port_vport_find(mlxsw_sp_port, vid);
if (!mlxsw_sp_vport) {
netdev_warn(dev, "VID=%d does not exist\n", vid);
return 0;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
vfid = mlxsw_sp_vport->vport.vfid;
err = mlxsw_sp_port_stp_state_set(mlxsw_sp_vport, vid,
MLXSW_REG_SPMS_STATE_DISCARDING);
if (err) {
netdev_err(dev, "Failed to set STP state for VID=%d\n", vid);
return err;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err = mlxsw_sp_port_vlan_set(mlxsw_sp_vport, vid, vid, false, false);
if (err) {
netdev_err(dev, "Failed to set VLAN membership for VID=%d\n",
vid);
return err;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err = mlxsw_sp_port_vid_learning_set(mlxsw_sp_vport, vid, true);
if (err) {
netdev_err(dev, "Failed to enable learning for VID=%d\n", vid);
return err;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID,
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
false,
mlxsw_sp_vfid_to_fid(vfid->vfid),
vid);
if (err) {
netdev_err(dev, "Failed to invalidate {Port, VID=%d} to vFID=%d mapping\n",
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
vid, vfid->vfid);
return err;
}
/* When removing the last VLAN interface on a bridged port we need to
* transition all active 802.1Q bridge VLANs to use VID to FID
* mappings and set port's mode to VLAN mode.
*/
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
if (list_is_singular(&mlxsw_sp_port->vports_list)) {
err = mlxsw_sp_port_vlan_mode_trans(mlxsw_sp_port);
if (err) {
netdev_err(dev, "Failed to set to VLAN mode\n");
return err;
}
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
vfid->nr_vports--;
mlxsw_sp_port_vport_destroy(mlxsw_sp_vport);
/* Destroy the vFID if no vPorts are assigned to it anymore. */
if (!vfid->nr_vports)
mlxsw_sp_vfid_destroy(mlxsw_sp_port->mlxsw_sp, vfid);
return 0;
}
static int mlxsw_sp_port_get_phys_port_name(struct net_device *dev, char *name,
size_t len)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
u8 module, width, lane;
int err;
err = __mlxsw_sp_port_module_info_get(mlxsw_sp_port->mlxsw_sp,
mlxsw_sp_port->local_port,
&module, &width, &lane);
if (err) {
netdev_err(dev, "Failed to retrieve module information\n");
return err;
}
if (!mlxsw_sp_port->split)
err = snprintf(name, len, "p%d", module + 1);
else
err = snprintf(name, len, "p%ds%d", module + 1,
lane / width);
if (err >= len)
return -EINVAL;
return 0;
}
static const struct net_device_ops mlxsw_sp_port_netdev_ops = {
.ndo_open = mlxsw_sp_port_open,
.ndo_stop = mlxsw_sp_port_stop,
.ndo_start_xmit = mlxsw_sp_port_xmit,
.ndo_set_rx_mode = mlxsw_sp_set_rx_mode,
.ndo_set_mac_address = mlxsw_sp_port_set_mac_address,
.ndo_change_mtu = mlxsw_sp_port_change_mtu,
.ndo_get_stats64 = mlxsw_sp_port_get_stats64,
.ndo_vlan_rx_add_vid = mlxsw_sp_port_add_vid,
.ndo_vlan_rx_kill_vid = mlxsw_sp_port_kill_vid,
.ndo_fdb_add = switchdev_port_fdb_add,
.ndo_fdb_del = switchdev_port_fdb_del,
.ndo_fdb_dump = switchdev_port_fdb_dump,
.ndo_bridge_setlink = switchdev_port_bridge_setlink,
.ndo_bridge_getlink = switchdev_port_bridge_getlink,
.ndo_bridge_dellink = switchdev_port_bridge_dellink,
.ndo_get_phys_port_name = mlxsw_sp_port_get_phys_port_name,
};
static void mlxsw_sp_port_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *drvinfo)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
strlcpy(drvinfo->driver, mlxsw_sp_driver_name, sizeof(drvinfo->driver));
strlcpy(drvinfo->version, mlxsw_sp_driver_version,
sizeof(drvinfo->version));
snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version),
"%d.%d.%d",
mlxsw_sp->bus_info->fw_rev.major,
mlxsw_sp->bus_info->fw_rev.minor,
mlxsw_sp->bus_info->fw_rev.subminor);
strlcpy(drvinfo->bus_info, mlxsw_sp->bus_info->device_name,
sizeof(drvinfo->bus_info));
}
struct mlxsw_sp_port_hw_stats {
char str[ETH_GSTRING_LEN];
u64 (*getter)(char *payload);
};
static const struct mlxsw_sp_port_hw_stats mlxsw_sp_port_hw_stats[] = {
{
.str = "a_frames_transmitted_ok",
.getter = mlxsw_reg_ppcnt_a_frames_transmitted_ok_get,
},
{
.str = "a_frames_received_ok",
.getter = mlxsw_reg_ppcnt_a_frames_received_ok_get,
},
{
.str = "a_frame_check_sequence_errors",
.getter = mlxsw_reg_ppcnt_a_frame_check_sequence_errors_get,
},
{
.str = "a_alignment_errors",
.getter = mlxsw_reg_ppcnt_a_alignment_errors_get,
},
{
.str = "a_octets_transmitted_ok",
.getter = mlxsw_reg_ppcnt_a_octets_transmitted_ok_get,
},
{
.str = "a_octets_received_ok",
.getter = mlxsw_reg_ppcnt_a_octets_received_ok_get,
},
{
.str = "a_multicast_frames_xmitted_ok",
.getter = mlxsw_reg_ppcnt_a_multicast_frames_xmitted_ok_get,
},
{
.str = "a_broadcast_frames_xmitted_ok",
.getter = mlxsw_reg_ppcnt_a_broadcast_frames_xmitted_ok_get,
},
{
.str = "a_multicast_frames_received_ok",
.getter = mlxsw_reg_ppcnt_a_multicast_frames_received_ok_get,
},
{
.str = "a_broadcast_frames_received_ok",
.getter = mlxsw_reg_ppcnt_a_broadcast_frames_received_ok_get,
},
{
.str = "a_in_range_length_errors",
.getter = mlxsw_reg_ppcnt_a_in_range_length_errors_get,
},
{
.str = "a_out_of_range_length_field",
.getter = mlxsw_reg_ppcnt_a_out_of_range_length_field_get,
},
{
.str = "a_frame_too_long_errors",
.getter = mlxsw_reg_ppcnt_a_frame_too_long_errors_get,
},
{
.str = "a_symbol_error_during_carrier",
.getter = mlxsw_reg_ppcnt_a_symbol_error_during_carrier_get,
},
{
.str = "a_mac_control_frames_transmitted",
.getter = mlxsw_reg_ppcnt_a_mac_control_frames_transmitted_get,
},
{
.str = "a_mac_control_frames_received",
.getter = mlxsw_reg_ppcnt_a_mac_control_frames_received_get,
},
{
.str = "a_unsupported_opcodes_received",
.getter = mlxsw_reg_ppcnt_a_unsupported_opcodes_received_get,
},
{
.str = "a_pause_mac_ctrl_frames_received",
.getter = mlxsw_reg_ppcnt_a_pause_mac_ctrl_frames_received_get,
},
{
.str = "a_pause_mac_ctrl_frames_xmitted",
.getter = mlxsw_reg_ppcnt_a_pause_mac_ctrl_frames_transmitted_get,
},
};
#define MLXSW_SP_PORT_HW_STATS_LEN ARRAY_SIZE(mlxsw_sp_port_hw_stats)
static void mlxsw_sp_port_get_strings(struct net_device *dev,
u32 stringset, u8 *data)
{
u8 *p = data;
int i;
switch (stringset) {
case ETH_SS_STATS:
for (i = 0; i < MLXSW_SP_PORT_HW_STATS_LEN; i++) {
memcpy(p, mlxsw_sp_port_hw_stats[i].str,
ETH_GSTRING_LEN);
p += ETH_GSTRING_LEN;
}
break;
}
}
static int mlxsw_sp_port_set_phys_id(struct net_device *dev,
enum ethtool_phys_id_state state)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char mlcr_pl[MLXSW_REG_MLCR_LEN];
bool active;
switch (state) {
case ETHTOOL_ID_ACTIVE:
active = true;
break;
case ETHTOOL_ID_INACTIVE:
active = false;
break;
default:
return -EOPNOTSUPP;
}
mlxsw_reg_mlcr_pack(mlcr_pl, mlxsw_sp_port->local_port, active);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(mlcr), mlcr_pl);
}
static void mlxsw_sp_port_get_stats(struct net_device *dev,
struct ethtool_stats *stats, u64 *data)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char ppcnt_pl[MLXSW_REG_PPCNT_LEN];
int i;
int err;
mlxsw_reg_ppcnt_pack(ppcnt_pl, mlxsw_sp_port->local_port);
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(ppcnt), ppcnt_pl);
for (i = 0; i < MLXSW_SP_PORT_HW_STATS_LEN; i++)
data[i] = !err ? mlxsw_sp_port_hw_stats[i].getter(ppcnt_pl) : 0;
}
static int mlxsw_sp_port_get_sset_count(struct net_device *dev, int sset)
{
switch (sset) {
case ETH_SS_STATS:
return MLXSW_SP_PORT_HW_STATS_LEN;
default:
return -EOPNOTSUPP;
}
}
struct mlxsw_sp_port_link_mode {
u32 mask;
u32 supported;
u32 advertised;
u32 speed;
};
static const struct mlxsw_sp_port_link_mode mlxsw_sp_port_link_mode[] = {
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_100BASE_T,
.supported = SUPPORTED_100baseT_Full,
.advertised = ADVERTISED_100baseT_Full,
.speed = 100,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_100BASE_TX,
.speed = 100,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_SGMII |
MLXSW_REG_PTYS_ETH_SPEED_1000BASE_KX,
.supported = SUPPORTED_1000baseKX_Full,
.advertised = ADVERTISED_1000baseKX_Full,
.speed = 1000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_10GBASE_T,
.supported = SUPPORTED_10000baseT_Full,
.advertised = ADVERTISED_10000baseT_Full,
.speed = 10000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_10GBASE_CX4 |
MLXSW_REG_PTYS_ETH_SPEED_10GBASE_KX4,
.supported = SUPPORTED_10000baseKX4_Full,
.advertised = ADVERTISED_10000baseKX4_Full,
.speed = 10000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_10GBASE_KR |
MLXSW_REG_PTYS_ETH_SPEED_10GBASE_CR |
MLXSW_REG_PTYS_ETH_SPEED_10GBASE_SR |
MLXSW_REG_PTYS_ETH_SPEED_10GBASE_ER_LR,
.supported = SUPPORTED_10000baseKR_Full,
.advertised = ADVERTISED_10000baseKR_Full,
.speed = 10000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_20GBASE_KR2,
.supported = SUPPORTED_20000baseKR2_Full,
.advertised = ADVERTISED_20000baseKR2_Full,
.speed = 20000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_40GBASE_CR4,
.supported = SUPPORTED_40000baseCR4_Full,
.advertised = ADVERTISED_40000baseCR4_Full,
.speed = 40000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_40GBASE_KR4,
.supported = SUPPORTED_40000baseKR4_Full,
.advertised = ADVERTISED_40000baseKR4_Full,
.speed = 40000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_40GBASE_SR4,
.supported = SUPPORTED_40000baseSR4_Full,
.advertised = ADVERTISED_40000baseSR4_Full,
.speed = 40000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_40GBASE_LR4_ER4,
.supported = SUPPORTED_40000baseLR4_Full,
.advertised = ADVERTISED_40000baseLR4_Full,
.speed = 40000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_25GBASE_CR |
MLXSW_REG_PTYS_ETH_SPEED_25GBASE_KR |
MLXSW_REG_PTYS_ETH_SPEED_25GBASE_SR,
.speed = 25000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_50GBASE_KR4 |
MLXSW_REG_PTYS_ETH_SPEED_50GBASE_CR2 |
MLXSW_REG_PTYS_ETH_SPEED_50GBASE_KR2,
.speed = 50000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_56GBASE_R4,
.supported = SUPPORTED_56000baseKR4_Full,
.advertised = ADVERTISED_56000baseKR4_Full,
.speed = 56000,
},
{
.mask = MLXSW_REG_PTYS_ETH_SPEED_100GBASE_CR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_SR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_KR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_LR4_ER4,
.speed = 100000,
},
};
#define MLXSW_SP_PORT_LINK_MODE_LEN ARRAY_SIZE(mlxsw_sp_port_link_mode)
static u32 mlxsw_sp_from_ptys_supported_port(u32 ptys_eth_proto)
{
if (ptys_eth_proto & (MLXSW_REG_PTYS_ETH_SPEED_10GBASE_CR |
MLXSW_REG_PTYS_ETH_SPEED_10GBASE_SR |
MLXSW_REG_PTYS_ETH_SPEED_40GBASE_CR4 |
MLXSW_REG_PTYS_ETH_SPEED_40GBASE_SR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_SR4 |
MLXSW_REG_PTYS_ETH_SPEED_SGMII))
return SUPPORTED_FIBRE;
if (ptys_eth_proto & (MLXSW_REG_PTYS_ETH_SPEED_10GBASE_KR |
MLXSW_REG_PTYS_ETH_SPEED_10GBASE_KX4 |
MLXSW_REG_PTYS_ETH_SPEED_40GBASE_KR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_KR4 |
MLXSW_REG_PTYS_ETH_SPEED_1000BASE_KX))
return SUPPORTED_Backplane;
return 0;
}
static u32 mlxsw_sp_from_ptys_supported_link(u32 ptys_eth_proto)
{
u32 modes = 0;
int i;
for (i = 0; i < MLXSW_SP_PORT_LINK_MODE_LEN; i++) {
if (ptys_eth_proto & mlxsw_sp_port_link_mode[i].mask)
modes |= mlxsw_sp_port_link_mode[i].supported;
}
return modes;
}
static u32 mlxsw_sp_from_ptys_advert_link(u32 ptys_eth_proto)
{
u32 modes = 0;
int i;
for (i = 0; i < MLXSW_SP_PORT_LINK_MODE_LEN; i++) {
if (ptys_eth_proto & mlxsw_sp_port_link_mode[i].mask)
modes |= mlxsw_sp_port_link_mode[i].advertised;
}
return modes;
}
static void mlxsw_sp_from_ptys_speed_duplex(bool carrier_ok, u32 ptys_eth_proto,
struct ethtool_cmd *cmd)
{
u32 speed = SPEED_UNKNOWN;
u8 duplex = DUPLEX_UNKNOWN;
int i;
if (!carrier_ok)
goto out;
for (i = 0; i < MLXSW_SP_PORT_LINK_MODE_LEN; i++) {
if (ptys_eth_proto & mlxsw_sp_port_link_mode[i].mask) {
speed = mlxsw_sp_port_link_mode[i].speed;
duplex = DUPLEX_FULL;
break;
}
}
out:
ethtool_cmd_speed_set(cmd, speed);
cmd->duplex = duplex;
}
static u8 mlxsw_sp_port_connector_port(u32 ptys_eth_proto)
{
if (ptys_eth_proto & (MLXSW_REG_PTYS_ETH_SPEED_10GBASE_SR |
MLXSW_REG_PTYS_ETH_SPEED_40GBASE_SR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_SR4 |
MLXSW_REG_PTYS_ETH_SPEED_SGMII))
return PORT_FIBRE;
if (ptys_eth_proto & (MLXSW_REG_PTYS_ETH_SPEED_10GBASE_CR |
MLXSW_REG_PTYS_ETH_SPEED_40GBASE_CR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_CR4))
return PORT_DA;
if (ptys_eth_proto & (MLXSW_REG_PTYS_ETH_SPEED_10GBASE_KR |
MLXSW_REG_PTYS_ETH_SPEED_10GBASE_KX4 |
MLXSW_REG_PTYS_ETH_SPEED_40GBASE_KR4 |
MLXSW_REG_PTYS_ETH_SPEED_100GBASE_KR4))
return PORT_NONE;
return PORT_OTHER;
}
static int mlxsw_sp_port_get_settings(struct net_device *dev,
struct ethtool_cmd *cmd)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char ptys_pl[MLXSW_REG_PTYS_LEN];
u32 eth_proto_cap;
u32 eth_proto_admin;
u32 eth_proto_oper;
int err;
mlxsw_reg_ptys_pack(ptys_pl, mlxsw_sp_port->local_port, 0);
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(ptys), ptys_pl);
if (err) {
netdev_err(dev, "Failed to get proto");
return err;
}
mlxsw_reg_ptys_unpack(ptys_pl, &eth_proto_cap,
&eth_proto_admin, &eth_proto_oper);
cmd->supported = mlxsw_sp_from_ptys_supported_port(eth_proto_cap) |
mlxsw_sp_from_ptys_supported_link(eth_proto_cap) |
SUPPORTED_Pause | SUPPORTED_Asym_Pause;
cmd->advertising = mlxsw_sp_from_ptys_advert_link(eth_proto_admin);
mlxsw_sp_from_ptys_speed_duplex(netif_carrier_ok(dev),
eth_proto_oper, cmd);
eth_proto_oper = eth_proto_oper ? eth_proto_oper : eth_proto_cap;
cmd->port = mlxsw_sp_port_connector_port(eth_proto_oper);
cmd->lp_advertising = mlxsw_sp_from_ptys_advert_link(eth_proto_oper);
cmd->transceiver = XCVR_INTERNAL;
return 0;
}
static u32 mlxsw_sp_to_ptys_advert_link(u32 advertising)
{
u32 ptys_proto = 0;
int i;
for (i = 0; i < MLXSW_SP_PORT_LINK_MODE_LEN; i++) {
if (advertising & mlxsw_sp_port_link_mode[i].advertised)
ptys_proto |= mlxsw_sp_port_link_mode[i].mask;
}
return ptys_proto;
}
static u32 mlxsw_sp_to_ptys_speed(u32 speed)
{
u32 ptys_proto = 0;
int i;
for (i = 0; i < MLXSW_SP_PORT_LINK_MODE_LEN; i++) {
if (speed == mlxsw_sp_port_link_mode[i].speed)
ptys_proto |= mlxsw_sp_port_link_mode[i].mask;
}
return ptys_proto;
}
static u32 mlxsw_sp_to_ptys_upper_speed(u32 upper_speed)
{
u32 ptys_proto = 0;
int i;
for (i = 0; i < MLXSW_SP_PORT_LINK_MODE_LEN; i++) {
if (mlxsw_sp_port_link_mode[i].speed <= upper_speed)
ptys_proto |= mlxsw_sp_port_link_mode[i].mask;
}
return ptys_proto;
}
static int mlxsw_sp_port_set_settings(struct net_device *dev,
struct ethtool_cmd *cmd)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char ptys_pl[MLXSW_REG_PTYS_LEN];
u32 speed;
u32 eth_proto_new;
u32 eth_proto_cap;
u32 eth_proto_admin;
bool is_up;
int err;
speed = ethtool_cmd_speed(cmd);
eth_proto_new = cmd->autoneg == AUTONEG_ENABLE ?
mlxsw_sp_to_ptys_advert_link(cmd->advertising) :
mlxsw_sp_to_ptys_speed(speed);
mlxsw_reg_ptys_pack(ptys_pl, mlxsw_sp_port->local_port, 0);
err = mlxsw_reg_query(mlxsw_sp->core, MLXSW_REG(ptys), ptys_pl);
if (err) {
netdev_err(dev, "Failed to get proto");
return err;
}
mlxsw_reg_ptys_unpack(ptys_pl, &eth_proto_cap, &eth_proto_admin, NULL);
eth_proto_new = eth_proto_new & eth_proto_cap;
if (!eth_proto_new) {
netdev_err(dev, "Not supported proto admin requested");
return -EINVAL;
}
if (eth_proto_new == eth_proto_admin)
return 0;
mlxsw_reg_ptys_pack(ptys_pl, mlxsw_sp_port->local_port, eth_proto_new);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(ptys), ptys_pl);
if (err) {
netdev_err(dev, "Failed to set proto admin");
return err;
}
err = mlxsw_sp_port_oper_status_get(mlxsw_sp_port, &is_up);
if (err) {
netdev_err(dev, "Failed to get oper status");
return err;
}
if (!is_up)
return 0;
err = mlxsw_sp_port_admin_status_set(mlxsw_sp_port, false);
if (err) {
netdev_err(dev, "Failed to set admin status");
return err;
}
err = mlxsw_sp_port_admin_status_set(mlxsw_sp_port, true);
if (err) {
netdev_err(dev, "Failed to set admin status");
return err;
}
return 0;
}
static const struct ethtool_ops mlxsw_sp_port_ethtool_ops = {
.get_drvinfo = mlxsw_sp_port_get_drvinfo,
.get_link = ethtool_op_get_link,
.get_strings = mlxsw_sp_port_get_strings,
.set_phys_id = mlxsw_sp_port_set_phys_id,
.get_ethtool_stats = mlxsw_sp_port_get_stats,
.get_sset_count = mlxsw_sp_port_get_sset_count,
.get_settings = mlxsw_sp_port_get_settings,
.set_settings = mlxsw_sp_port_set_settings,
};
static int
mlxsw_sp_port_speed_by_width_set(struct mlxsw_sp_port *mlxsw_sp_port, u8 width)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
u32 upper_speed = MLXSW_SP_PORT_BASE_SPEED * width;
char ptys_pl[MLXSW_REG_PTYS_LEN];
u32 eth_proto_admin;
eth_proto_admin = mlxsw_sp_to_ptys_upper_speed(upper_speed);
mlxsw_reg_ptys_pack(ptys_pl, mlxsw_sp_port->local_port,
eth_proto_admin);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(ptys), ptys_pl);
}
static int mlxsw_sp_port_ets_set(struct mlxsw_sp_port *mlxsw_sp_port,
enum mlxsw_reg_qeec_hr hr, u8 index,
u8 next_index, bool dwrr, u8 dwrr_weight)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char qeec_pl[MLXSW_REG_QEEC_LEN];
mlxsw_reg_qeec_pack(qeec_pl, mlxsw_sp_port->local_port, hr, index,
next_index);
mlxsw_reg_qeec_de_set(qeec_pl, true);
mlxsw_reg_qeec_dwrr_set(qeec_pl, dwrr);
mlxsw_reg_qeec_dwrr_weight_set(qeec_pl, dwrr_weight);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(qeec), qeec_pl);
}
static int mlxsw_sp_port_ets_maxrate_set(struct mlxsw_sp_port *mlxsw_sp_port,
enum mlxsw_reg_qeec_hr hr, u8 index,
u8 next_index, u32 maxrate)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char qeec_pl[MLXSW_REG_QEEC_LEN];
mlxsw_reg_qeec_pack(qeec_pl, mlxsw_sp_port->local_port, hr, index,
next_index);
mlxsw_reg_qeec_mase_set(qeec_pl, true);
mlxsw_reg_qeec_max_shaper_rate_set(qeec_pl, maxrate);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(qeec), qeec_pl);
}
static int mlxsw_sp_port_prio_tc_set(struct mlxsw_sp_port *mlxsw_sp_port,
u8 switch_prio, u8 tclass)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char qtct_pl[MLXSW_REG_QTCT_LEN];
mlxsw_reg_qtct_pack(qtct_pl, mlxsw_sp_port->local_port, switch_prio,
tclass);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(qtct), qtct_pl);
}
static int mlxsw_sp_port_ets_init(struct mlxsw_sp_port *mlxsw_sp_port)
{
int err, i;
/* Setup the elements hierarcy, so that each TC is linked to
* one subgroup, which are all member in the same group.
*/
err = mlxsw_sp_port_ets_set(mlxsw_sp_port,
MLXSW_REG_QEEC_HIERARCY_GROUP, 0, 0, false,
0);
if (err)
return err;
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
err = mlxsw_sp_port_ets_set(mlxsw_sp_port,
MLXSW_REG_QEEC_HIERARCY_SUBGROUP, i,
0, false, 0);
if (err)
return err;
}
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
err = mlxsw_sp_port_ets_set(mlxsw_sp_port,
MLXSW_REG_QEEC_HIERARCY_TC, i, i,
false, 0);
if (err)
return err;
}
/* Make sure the max shaper is disabled in all hierarcies that
* support it.
*/
err = mlxsw_sp_port_ets_maxrate_set(mlxsw_sp_port,
MLXSW_REG_QEEC_HIERARCY_PORT, 0, 0,
MLXSW_REG_QEEC_MAS_DIS);
if (err)
return err;
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
err = mlxsw_sp_port_ets_maxrate_set(mlxsw_sp_port,
MLXSW_REG_QEEC_HIERARCY_SUBGROUP,
i, 0,
MLXSW_REG_QEEC_MAS_DIS);
if (err)
return err;
}
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
err = mlxsw_sp_port_ets_maxrate_set(mlxsw_sp_port,
MLXSW_REG_QEEC_HIERARCY_TC,
i, i,
MLXSW_REG_QEEC_MAS_DIS);
if (err)
return err;
}
/* Map all priorities to traffic class 0. */
for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {
err = mlxsw_sp_port_prio_tc_set(mlxsw_sp_port, i, 0);
if (err)
return err;
}
return 0;
}
static int __mlxsw_sp_port_create(struct mlxsw_sp *mlxsw_sp, u8 local_port,
bool split, u8 module, u8 width)
{
struct devlink *devlink = priv_to_devlink(mlxsw_sp->core);
struct mlxsw_sp_port *mlxsw_sp_port;
struct devlink_port *devlink_port;
struct net_device *dev;
size_t bytes;
int err;
dev = alloc_etherdev(sizeof(struct mlxsw_sp_port));
if (!dev)
return -ENOMEM;
mlxsw_sp_port = netdev_priv(dev);
mlxsw_sp_port->dev = dev;
mlxsw_sp_port->mlxsw_sp = mlxsw_sp;
mlxsw_sp_port->local_port = local_port;
mlxsw_sp_port->split = split;
bytes = DIV_ROUND_UP(VLAN_N_VID, BITS_PER_BYTE);
mlxsw_sp_port->active_vlans = kzalloc(bytes, GFP_KERNEL);
if (!mlxsw_sp_port->active_vlans) {
err = -ENOMEM;
goto err_port_active_vlans_alloc;
}
mlxsw_sp_port->untagged_vlans = kzalloc(bytes, GFP_KERNEL);
if (!mlxsw_sp_port->untagged_vlans) {
err = -ENOMEM;
goto err_port_untagged_vlans_alloc;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
INIT_LIST_HEAD(&mlxsw_sp_port->vports_list);
mlxsw_sp_port->pcpu_stats =
netdev_alloc_pcpu_stats(struct mlxsw_sp_port_pcpu_stats);
if (!mlxsw_sp_port->pcpu_stats) {
err = -ENOMEM;
goto err_alloc_stats;
}
dev->netdev_ops = &mlxsw_sp_port_netdev_ops;
dev->ethtool_ops = &mlxsw_sp_port_ethtool_ops;
err = mlxsw_sp_port_dev_addr_init(mlxsw_sp_port);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Unable to init port mac address\n",
mlxsw_sp_port->local_port);
goto err_dev_addr_init;
}
netif_carrier_off(dev);
dev->features |= NETIF_F_NETNS_LOCAL | NETIF_F_LLTX | NETIF_F_SG |
NETIF_F_HW_VLAN_CTAG_FILTER;
/* Each packet needs to have a Tx header (metadata) on top all other
* headers.
*/
dev->hard_header_len += MLXSW_TXHDR_LEN;
devlink_port = &mlxsw_sp_port->devlink_port;
if (mlxsw_sp_port->split)
devlink_port_split_set(devlink_port, module);
err = devlink_port_register(devlink, devlink_port, local_port);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to register devlink port\n",
mlxsw_sp_port->local_port);
goto err_devlink_port_register;
}
err = mlxsw_sp_port_system_port_mapping_set(mlxsw_sp_port);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to set system port mapping\n",
mlxsw_sp_port->local_port);
goto err_port_system_port_mapping_set;
}
err = mlxsw_sp_port_swid_set(mlxsw_sp_port, 0);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to set SWID\n",
mlxsw_sp_port->local_port);
goto err_port_swid_set;
}
err = mlxsw_sp_port_speed_by_width_set(mlxsw_sp_port, width);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to enable speeds\n",
mlxsw_sp_port->local_port);
goto err_port_speed_by_width_set;
}
err = mlxsw_sp_port_mtu_set(mlxsw_sp_port, ETH_DATA_LEN);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to set MTU\n",
mlxsw_sp_port->local_port);
goto err_port_mtu_set;
}
err = mlxsw_sp_port_admin_status_set(mlxsw_sp_port, false);
if (err)
goto err_port_admin_status_set;
err = mlxsw_sp_port_buffers_init(mlxsw_sp_port);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to initialize buffers\n",
mlxsw_sp_port->local_port);
goto err_port_buffers_init;
}
err = mlxsw_sp_port_ets_init(mlxsw_sp_port);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to initialize ETS\n",
mlxsw_sp_port->local_port);
goto err_port_ets_init;
}
/* ETS and buffers must be initialized before DCB. */
err = mlxsw_sp_port_dcb_init(mlxsw_sp_port);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to initialize DCB\n",
mlxsw_sp_port->local_port);
goto err_port_dcb_init;
}
mlxsw_sp_port_switchdev_init(mlxsw_sp_port);
err = register_netdev(dev);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Port %d: Failed to register netdev\n",
mlxsw_sp_port->local_port);
goto err_register_netdev;
}
devlink_port_type_eth_set(devlink_port, dev);
err = mlxsw_sp_port_vlan_init(mlxsw_sp_port);
if (err)
goto err_port_vlan_init;
mlxsw_sp->ports[local_port] = mlxsw_sp_port;
return 0;
err_port_vlan_init:
unregister_netdev(dev);
err_register_netdev:
err_port_dcb_init:
err_port_ets_init:
err_port_buffers_init:
err_port_admin_status_set:
err_port_mtu_set:
err_port_speed_by_width_set:
err_port_swid_set:
err_port_system_port_mapping_set:
devlink_port_unregister(&mlxsw_sp_port->devlink_port);
err_devlink_port_register:
err_dev_addr_init:
free_percpu(mlxsw_sp_port->pcpu_stats);
err_alloc_stats:
kfree(mlxsw_sp_port->untagged_vlans);
err_port_untagged_vlans_alloc:
kfree(mlxsw_sp_port->active_vlans);
err_port_active_vlans_alloc:
free_netdev(dev);
return err;
}
static int mlxsw_sp_port_create(struct mlxsw_sp *mlxsw_sp, u8 local_port,
bool split, u8 module, u8 width, u8 lane)
{
int err;
err = mlxsw_sp_port_module_map(mlxsw_sp, local_port, module, width,
lane);
if (err)
return err;
err = __mlxsw_sp_port_create(mlxsw_sp, local_port, split, module,
width);
if (err)
goto err_port_create;
return 0;
err_port_create:
mlxsw_sp_port_module_unmap(mlxsw_sp, local_port);
return err;
}
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
static void mlxsw_sp_port_vports_fini(struct mlxsw_sp_port *mlxsw_sp_port)
{
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
struct net_device *dev = mlxsw_sp_port->dev;
struct mlxsw_sp_port *mlxsw_sp_vport, *tmp;
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
list_for_each_entry_safe(mlxsw_sp_vport, tmp,
&mlxsw_sp_port->vports_list, vport.list) {
u16 vid = mlxsw_sp_vport_vid_get(mlxsw_sp_vport);
/* vPorts created for VLAN devices should already be gone
* by now, since we unregistered the port netdev.
*/
WARN_ON(is_vlan_dev(mlxsw_sp_vport->dev));
mlxsw_sp_port_kill_vid(dev, 0, vid);
}
}
static void mlxsw_sp_port_remove(struct mlxsw_sp *mlxsw_sp, u8 local_port)
{
struct mlxsw_sp_port *mlxsw_sp_port = mlxsw_sp->ports[local_port];
struct devlink_port *devlink_port;
if (!mlxsw_sp_port)
return;
mlxsw_sp->ports[local_port] = NULL;
devlink_port = &mlxsw_sp_port->devlink_port;
devlink_port_type_clear(devlink_port);
unregister_netdev(mlxsw_sp_port->dev); /* This calls ndo_stop */
mlxsw_sp_port_dcb_fini(mlxsw_sp_port);
devlink_port_unregister(devlink_port);
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
mlxsw_sp_port_vports_fini(mlxsw_sp_port);
mlxsw_sp_port_switchdev_fini(mlxsw_sp_port);
mlxsw_sp_port_swid_set(mlxsw_sp_port, MLXSW_PORT_SWID_DISABLED_PORT);
mlxsw_sp_port_module_unmap(mlxsw_sp, mlxsw_sp_port->local_port);
free_percpu(mlxsw_sp_port->pcpu_stats);
kfree(mlxsw_sp_port->untagged_vlans);
kfree(mlxsw_sp_port->active_vlans);
free_netdev(mlxsw_sp_port->dev);
}
static void mlxsw_sp_ports_remove(struct mlxsw_sp *mlxsw_sp)
{
int i;
for (i = 1; i < MLXSW_PORT_MAX_PORTS; i++)
mlxsw_sp_port_remove(mlxsw_sp, i);
kfree(mlxsw_sp->ports);
}
static int mlxsw_sp_ports_create(struct mlxsw_sp *mlxsw_sp)
{
size_t alloc_size;
u8 module, width;
int i;
int err;
alloc_size = sizeof(struct mlxsw_sp_port *) * MLXSW_PORT_MAX_PORTS;
mlxsw_sp->ports = kzalloc(alloc_size, GFP_KERNEL);
if (!mlxsw_sp->ports)
return -ENOMEM;
for (i = 1; i < MLXSW_PORT_MAX_PORTS; i++) {
err = mlxsw_sp_port_module_info_get(mlxsw_sp, i, &module,
&width);
if (err)
goto err_port_module_info_get;
if (!width)
continue;
mlxsw_sp->port_to_module[i] = module;
err = __mlxsw_sp_port_create(mlxsw_sp, i, false, module, width);
if (err)
goto err_port_create;
}
return 0;
err_port_create:
err_port_module_info_get:
for (i--; i >= 1; i--)
mlxsw_sp_port_remove(mlxsw_sp, i);
kfree(mlxsw_sp->ports);
return err;
}
static u8 mlxsw_sp_cluster_base_port_get(u8 local_port)
{
u8 offset = (local_port - 1) % MLXSW_SP_PORTS_PER_CLUSTER_MAX;
return local_port - offset;
}
static int mlxsw_sp_port_split(void *priv, u8 local_port, unsigned int count)
{
struct mlxsw_sp *mlxsw_sp = priv;
struct mlxsw_sp_port *mlxsw_sp_port;
u8 width = MLXSW_PORT_MODULE_MAX_WIDTH / count;
u8 module, cur_width, base_port;
int i;
int err;
mlxsw_sp_port = mlxsw_sp->ports[local_port];
if (!mlxsw_sp_port) {
dev_err(mlxsw_sp->bus_info->dev, "Port number \"%d\" does not exist\n",
local_port);
return -EINVAL;
}
if (count != 2 && count != 4) {
netdev_err(mlxsw_sp_port->dev, "Port can only be split into 2 or 4 ports\n");
return -EINVAL;
}
err = mlxsw_sp_port_module_info_get(mlxsw_sp, local_port, &module,
&cur_width);
if (err) {
netdev_err(mlxsw_sp_port->dev, "Failed to get port's width\n");
return err;
}
if (cur_width != MLXSW_PORT_MODULE_MAX_WIDTH) {
netdev_err(mlxsw_sp_port->dev, "Port cannot be split further\n");
return -EINVAL;
}
/* Make sure we have enough slave (even) ports for the split. */
if (count == 2) {
base_port = local_port;
if (mlxsw_sp->ports[base_port + 1]) {
netdev_err(mlxsw_sp_port->dev, "Invalid split configuration\n");
return -EINVAL;
}
} else {
base_port = mlxsw_sp_cluster_base_port_get(local_port);
if (mlxsw_sp->ports[base_port + 1] ||
mlxsw_sp->ports[base_port + 3]) {
netdev_err(mlxsw_sp_port->dev, "Invalid split configuration\n");
return -EINVAL;
}
}
for (i = 0; i < count; i++)
mlxsw_sp_port_remove(mlxsw_sp, base_port + i);
for (i = 0; i < count; i++) {
err = mlxsw_sp_port_create(mlxsw_sp, base_port + i, true,
module, width, i * width);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to create split port\n");
goto err_port_create;
}
}
return 0;
err_port_create:
for (i--; i >= 0; i--)
mlxsw_sp_port_remove(mlxsw_sp, base_port + i);
for (i = 0; i < count / 2; i++) {
module = mlxsw_sp->port_to_module[base_port + i * 2];
mlxsw_sp_port_create(mlxsw_sp, base_port + i * 2, false,
module, MLXSW_PORT_MODULE_MAX_WIDTH, 0);
}
return err;
}
static int mlxsw_sp_port_unsplit(void *priv, u8 local_port)
{
struct mlxsw_sp *mlxsw_sp = priv;
struct mlxsw_sp_port *mlxsw_sp_port;
u8 module, cur_width, base_port;
unsigned int count;
int i;
int err;
mlxsw_sp_port = mlxsw_sp->ports[local_port];
if (!mlxsw_sp_port) {
dev_err(mlxsw_sp->bus_info->dev, "Port number \"%d\" does not exist\n",
local_port);
return -EINVAL;
}
if (!mlxsw_sp_port->split) {
netdev_err(mlxsw_sp_port->dev, "Port wasn't split\n");
return -EINVAL;
}
err = mlxsw_sp_port_module_info_get(mlxsw_sp, local_port, &module,
&cur_width);
if (err) {
netdev_err(mlxsw_sp_port->dev, "Failed to get port's width\n");
return err;
}
count = cur_width == 1 ? 4 : 2;
base_port = mlxsw_sp_cluster_base_port_get(local_port);
/* Determine which ports to remove. */
if (count == 2 && local_port >= base_port + 2)
base_port = base_port + 2;
for (i = 0; i < count; i++)
mlxsw_sp_port_remove(mlxsw_sp, base_port + i);
for (i = 0; i < count / 2; i++) {
module = mlxsw_sp->port_to_module[base_port + i * 2];
err = mlxsw_sp_port_create(mlxsw_sp, base_port + i * 2, false,
module, MLXSW_PORT_MODULE_MAX_WIDTH,
0);
if (err)
dev_err(mlxsw_sp->bus_info->dev, "Failed to reinstantiate port\n");
}
return 0;
}
static void mlxsw_sp_pude_event_func(const struct mlxsw_reg_info *reg,
char *pude_pl, void *priv)
{
struct mlxsw_sp *mlxsw_sp = priv;
struct mlxsw_sp_port *mlxsw_sp_port;
enum mlxsw_reg_pude_oper_status status;
u8 local_port;
local_port = mlxsw_reg_pude_local_port_get(pude_pl);
mlxsw_sp_port = mlxsw_sp->ports[local_port];
if (!mlxsw_sp_port) {
dev_warn(mlxsw_sp->bus_info->dev, "Port %d: Link event received for non-existent port\n",
local_port);
return;
}
status = mlxsw_reg_pude_oper_status_get(pude_pl);
if (status == MLXSW_PORT_OPER_STATUS_UP) {
netdev_info(mlxsw_sp_port->dev, "link up\n");
netif_carrier_on(mlxsw_sp_port->dev);
} else {
netdev_info(mlxsw_sp_port->dev, "link down\n");
netif_carrier_off(mlxsw_sp_port->dev);
}
}
static struct mlxsw_event_listener mlxsw_sp_pude_event = {
.func = mlxsw_sp_pude_event_func,
.trap_id = MLXSW_TRAP_ID_PUDE,
};
static int mlxsw_sp_event_register(struct mlxsw_sp *mlxsw_sp,
enum mlxsw_event_trap_id trap_id)
{
struct mlxsw_event_listener *el;
char hpkt_pl[MLXSW_REG_HPKT_LEN];
int err;
switch (trap_id) {
case MLXSW_TRAP_ID_PUDE:
el = &mlxsw_sp_pude_event;
break;
}
err = mlxsw_core_event_listener_register(mlxsw_sp->core, el, mlxsw_sp);
if (err)
return err;
mlxsw_reg_hpkt_pack(hpkt_pl, MLXSW_REG_HPKT_ACTION_FORWARD, trap_id);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(hpkt), hpkt_pl);
if (err)
goto err_event_trap_set;
return 0;
err_event_trap_set:
mlxsw_core_event_listener_unregister(mlxsw_sp->core, el, mlxsw_sp);
return err;
}
static void mlxsw_sp_event_unregister(struct mlxsw_sp *mlxsw_sp,
enum mlxsw_event_trap_id trap_id)
{
struct mlxsw_event_listener *el;
switch (trap_id) {
case MLXSW_TRAP_ID_PUDE:
el = &mlxsw_sp_pude_event;
break;
}
mlxsw_core_event_listener_unregister(mlxsw_sp->core, el, mlxsw_sp);
}
static void mlxsw_sp_rx_listener_func(struct sk_buff *skb, u8 local_port,
void *priv)
{
struct mlxsw_sp *mlxsw_sp = priv;
struct mlxsw_sp_port *mlxsw_sp_port = mlxsw_sp->ports[local_port];
struct mlxsw_sp_port_pcpu_stats *pcpu_stats;
if (unlikely(!mlxsw_sp_port)) {
dev_warn_ratelimited(mlxsw_sp->bus_info->dev, "Port %d: skb received for non-existent port\n",
local_port);
return;
}
skb->dev = mlxsw_sp_port->dev;
pcpu_stats = this_cpu_ptr(mlxsw_sp_port->pcpu_stats);
u64_stats_update_begin(&pcpu_stats->syncp);
pcpu_stats->rx_packets++;
pcpu_stats->rx_bytes += skb->len;
u64_stats_update_end(&pcpu_stats->syncp);
skb->protocol = eth_type_trans(skb, skb->dev);
netif_receive_skb(skb);
}
static const struct mlxsw_rx_listener mlxsw_sp_rx_listener[] = {
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_FDB_MC,
},
/* Traps for specific L2 packet types, not trapped as FDB MC */
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_STP,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_LACP,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_EAPOL,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_LLDP,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_MMRP,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_MVRP,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_RPVST,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_DHCP,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_IGMP_QUERY,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_IGMP_V1_REPORT,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_IGMP_V2_REPORT,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_IGMP_V2_LEAVE,
},
{
.func = mlxsw_sp_rx_listener_func,
.local_port = MLXSW_PORT_DONT_CARE,
.trap_id = MLXSW_TRAP_ID_IGMP_V3_REPORT,
},
};
static int mlxsw_sp_traps_init(struct mlxsw_sp *mlxsw_sp)
{
char htgt_pl[MLXSW_REG_HTGT_LEN];
char hpkt_pl[MLXSW_REG_HPKT_LEN];
int i;
int err;
mlxsw_reg_htgt_pack(htgt_pl, MLXSW_REG_HTGT_TRAP_GROUP_RX);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(htgt), htgt_pl);
if (err)
return err;
mlxsw_reg_htgt_pack(htgt_pl, MLXSW_REG_HTGT_TRAP_GROUP_CTRL);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(htgt), htgt_pl);
if (err)
return err;
for (i = 0; i < ARRAY_SIZE(mlxsw_sp_rx_listener); i++) {
err = mlxsw_core_rx_listener_register(mlxsw_sp->core,
&mlxsw_sp_rx_listener[i],
mlxsw_sp);
if (err)
goto err_rx_listener_register;
mlxsw_reg_hpkt_pack(hpkt_pl, MLXSW_REG_HPKT_ACTION_TRAP_TO_CPU,
mlxsw_sp_rx_listener[i].trap_id);
err = mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(hpkt), hpkt_pl);
if (err)
goto err_rx_trap_set;
}
return 0;
err_rx_trap_set:
mlxsw_core_rx_listener_unregister(mlxsw_sp->core,
&mlxsw_sp_rx_listener[i],
mlxsw_sp);
err_rx_listener_register:
for (i--; i >= 0; i--) {
mlxsw_reg_hpkt_pack(hpkt_pl, MLXSW_REG_HPKT_ACTION_FORWARD,
mlxsw_sp_rx_listener[i].trap_id);
mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(hpkt), hpkt_pl);
mlxsw_core_rx_listener_unregister(mlxsw_sp->core,
&mlxsw_sp_rx_listener[i],
mlxsw_sp);
}
return err;
}
static void mlxsw_sp_traps_fini(struct mlxsw_sp *mlxsw_sp)
{
char hpkt_pl[MLXSW_REG_HPKT_LEN];
int i;
for (i = 0; i < ARRAY_SIZE(mlxsw_sp_rx_listener); i++) {
mlxsw_reg_hpkt_pack(hpkt_pl, MLXSW_REG_HPKT_ACTION_FORWARD,
mlxsw_sp_rx_listener[i].trap_id);
mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(hpkt), hpkt_pl);
mlxsw_core_rx_listener_unregister(mlxsw_sp->core,
&mlxsw_sp_rx_listener[i],
mlxsw_sp);
}
}
static int __mlxsw_sp_flood_init(struct mlxsw_core *mlxsw_core,
enum mlxsw_reg_sfgc_type type,
enum mlxsw_reg_sfgc_bridge_type bridge_type)
{
enum mlxsw_flood_table_type table_type;
enum mlxsw_sp_flood_table flood_table;
char sfgc_pl[MLXSW_REG_SFGC_LEN];
if (bridge_type == MLXSW_REG_SFGC_BRIDGE_TYPE_VFID)
table_type = MLXSW_REG_SFGC_TABLE_TYPE_FID;
else
table_type = MLXSW_REG_SFGC_TABLE_TYPE_FID_OFFEST;
if (type == MLXSW_REG_SFGC_TYPE_UNKNOWN_UNICAST)
flood_table = MLXSW_SP_FLOOD_TABLE_UC;
else
flood_table = MLXSW_SP_FLOOD_TABLE_BM;
mlxsw_reg_sfgc_pack(sfgc_pl, type, bridge_type, table_type,
flood_table);
return mlxsw_reg_write(mlxsw_core, MLXSW_REG(sfgc), sfgc_pl);
}
static int mlxsw_sp_flood_init(struct mlxsw_sp *mlxsw_sp)
{
int type, err;
for (type = 0; type < MLXSW_REG_SFGC_TYPE_MAX; type++) {
if (type == MLXSW_REG_SFGC_TYPE_RESERVED)
continue;
err = __mlxsw_sp_flood_init(mlxsw_sp->core, type,
MLXSW_REG_SFGC_BRIDGE_TYPE_VFID);
if (err)
return err;
err = __mlxsw_sp_flood_init(mlxsw_sp->core, type,
MLXSW_REG_SFGC_BRIDGE_TYPE_1Q_FID);
if (err)
return err;
}
return 0;
}
static int mlxsw_sp_lag_init(struct mlxsw_sp *mlxsw_sp)
{
char slcr_pl[MLXSW_REG_SLCR_LEN];
mlxsw_reg_slcr_pack(slcr_pl, MLXSW_REG_SLCR_LAG_HASH_SMAC |
MLXSW_REG_SLCR_LAG_HASH_DMAC |
MLXSW_REG_SLCR_LAG_HASH_ETHERTYPE |
MLXSW_REG_SLCR_LAG_HASH_VLANID |
MLXSW_REG_SLCR_LAG_HASH_SIP |
MLXSW_REG_SLCR_LAG_HASH_DIP |
MLXSW_REG_SLCR_LAG_HASH_SPORT |
MLXSW_REG_SLCR_LAG_HASH_DPORT |
MLXSW_REG_SLCR_LAG_HASH_IPPROTO);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(slcr), slcr_pl);
}
static int mlxsw_sp_init(void *priv, struct mlxsw_core *mlxsw_core,
const struct mlxsw_bus_info *mlxsw_bus_info)
{
struct mlxsw_sp *mlxsw_sp = priv;
int err;
mlxsw_sp->core = mlxsw_core;
mlxsw_sp->bus_info = mlxsw_bus_info;
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
INIT_LIST_HEAD(&mlxsw_sp->port_vfids.list);
INIT_LIST_HEAD(&mlxsw_sp->br_vfids.list);
INIT_LIST_HEAD(&mlxsw_sp->br_mids.list);
err = mlxsw_sp_base_mac_get(mlxsw_sp);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to get base mac\n");
return err;
}
err = mlxsw_sp_ports_create(mlxsw_sp);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to create ports\n");
mlxsw: spectrum: Split vFID range in two Up until now we used a 1:1 mapping - based on VID - to map a VLAN interface to a vFID. However, a different scheme is needed in order to support bridges between VLAN interfaces, as all the member interfaces - which can have different VIDs - need to share the same vFID. Solve that by splitting the vFID range in two: 1. Non-bridged VLAN interfaces 2. Bridged VLAN interfaces When a VLAN interface is created, assign it the next available vFID in the first range, unless one already exists for that VID or number of vFIDs in the range was exceeded. When interface is removed, free the vFID, unless other interfaces are mapped to it. To accomplish the above: 1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which has a global context and holds a reference count. 2. Create a vPort (dummy in case of bridge SELF invocation) on top of of the physical port and hold a reference to the associated vFID. vfid vfid +-------------+ +-------------+ | vfid | | vfid | | vid +---> ... | vid | | nr_vports | | nr_vports | +------+------+ +------+------+ | +-----------------------+-------+ | | vport vport +-------------+ +-------------+ | ... | | ... | | *vfid +---> ... | *vfid +---> ... | ... | | ... | +------+------+ +------+------+ | | port port +-------------+ +-------------+ | ... | | ... | | vports_list | | vports_list | | ... | | ... | +-------------+ +-------------+ swXpY swXpZ Next patches in the series will add the missing infrastructure for the second range and transfer vPorts between the two ranges according to the received notifications. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15 22:03:37 +07:00
return err;
}
err = mlxsw_sp_event_register(mlxsw_sp, MLXSW_TRAP_ID_PUDE);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to register for PUDE events\n");
goto err_event_register;
}
err = mlxsw_sp_traps_init(mlxsw_sp);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to set traps for RX\n");
goto err_rx_listener_register;
}
err = mlxsw_sp_flood_init(mlxsw_sp);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to initialize flood tables\n");
goto err_flood_init;
}
err = mlxsw_sp_buffers_init(mlxsw_sp);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to initialize buffers\n");
goto err_buffers_init;
}
err = mlxsw_sp_lag_init(mlxsw_sp);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to initialize LAG\n");
goto err_lag_init;
}
err = mlxsw_sp_switchdev_init(mlxsw_sp);
if (err) {
dev_err(mlxsw_sp->bus_info->dev, "Failed to initialize switchdev\n");
goto err_switchdev_init;
}
return 0;
err_switchdev_init:
err_lag_init:
err_buffers_init:
err_flood_init:
mlxsw_sp_traps_fini(mlxsw_sp);
err_rx_listener_register:
mlxsw_sp_event_unregister(mlxsw_sp, MLXSW_TRAP_ID_PUDE);
err_event_register:
mlxsw_sp_ports_remove(mlxsw_sp);
return err;
}
static void mlxsw_sp_fini(void *priv)
{
struct mlxsw_sp *mlxsw_sp = priv;
mlxsw_sp_switchdev_fini(mlxsw_sp);
mlxsw_sp_traps_fini(mlxsw_sp);
mlxsw_sp_event_unregister(mlxsw_sp, MLXSW_TRAP_ID_PUDE);
mlxsw_sp_ports_remove(mlxsw_sp);
}
static struct mlxsw_config_profile mlxsw_sp_config_profile = {
.used_max_vepa_channels = 1,
.max_vepa_channels = 0,
.used_max_lag = 1,
.max_lag = MLXSW_SP_LAG_MAX,
.used_max_port_per_lag = 1,
.max_port_per_lag = MLXSW_SP_PORT_PER_LAG_MAX,
.used_max_mid = 1,
.max_mid = MLXSW_SP_MID_MAX,
.used_max_pgt = 1,
.max_pgt = 0,
.used_max_system_port = 1,
.max_system_port = 64,
.used_max_vlan_groups = 1,
.max_vlan_groups = 127,
.used_max_regions = 1,
.max_regions = 400,
.used_flood_tables = 1,
.used_flood_mode = 1,
.flood_mode = 3,
.max_fid_offset_flood_tables = 2,
.fid_offset_flood_table_size = VLAN_N_VID - 1,
.max_fid_flood_tables = 2,
.fid_flood_table_size = MLXSW_SP_VFID_MAX,
.used_max_ib_mc = 1,
.max_ib_mc = 0,
.used_max_pkey = 1,
.max_pkey = 0,
.swid_config = {
{
.used_type = 1,
.type = MLXSW_PORT_SWID_TYPE_ETH,
}
},
};
static struct mlxsw_driver mlxsw_sp_driver = {
.kind = MLXSW_DEVICE_KIND_SPECTRUM,
.owner = THIS_MODULE,
.priv_size = sizeof(struct mlxsw_sp),
.init = mlxsw_sp_init,
.fini = mlxsw_sp_fini,
.port_split = mlxsw_sp_port_split,
.port_unsplit = mlxsw_sp_port_unsplit,
.txhdr_construct = mlxsw_sp_txhdr_construct,
.txhdr_len = MLXSW_TXHDR_LEN,
.profile = &mlxsw_sp_config_profile,
};
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
static int
mlxsw_sp_port_fdb_flush_by_port(const struct mlxsw_sp_port *mlxsw_sp_port)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char sfdf_pl[MLXSW_REG_SFDF_LEN];
mlxsw_reg_sfdf_pack(sfdf_pl, MLXSW_REG_SFDF_FLUSH_PER_PORT);
mlxsw_reg_sfdf_system_port_set(sfdf_pl, mlxsw_sp_port->local_port);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sfdf), sfdf_pl);
}
static int
mlxsw_sp_port_fdb_flush_by_port_fid(const struct mlxsw_sp_port *mlxsw_sp_port,
u16 fid)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char sfdf_pl[MLXSW_REG_SFDF_LEN];
mlxsw_reg_sfdf_pack(sfdf_pl, MLXSW_REG_SFDF_FLUSH_PER_PORT_AND_FID);
mlxsw_reg_sfdf_fid_set(sfdf_pl, fid);
mlxsw_reg_sfdf_port_fid_system_port_set(sfdf_pl,
mlxsw_sp_port->local_port);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sfdf), sfdf_pl);
}
static int
mlxsw_sp_port_fdb_flush_by_lag_id(const struct mlxsw_sp_port *mlxsw_sp_port)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char sfdf_pl[MLXSW_REG_SFDF_LEN];
mlxsw_reg_sfdf_pack(sfdf_pl, MLXSW_REG_SFDF_FLUSH_PER_LAG);
mlxsw_reg_sfdf_lag_id_set(sfdf_pl, mlxsw_sp_port->lag_id);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sfdf), sfdf_pl);
}
static int
mlxsw_sp_port_fdb_flush_by_lag_id_fid(const struct mlxsw_sp_port *mlxsw_sp_port,
u16 fid)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char sfdf_pl[MLXSW_REG_SFDF_LEN];
mlxsw_reg_sfdf_pack(sfdf_pl, MLXSW_REG_SFDF_FLUSH_PER_LAG_AND_FID);
mlxsw_reg_sfdf_fid_set(sfdf_pl, fid);
mlxsw_reg_sfdf_lag_fid_lag_id_set(sfdf_pl, mlxsw_sp_port->lag_id);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sfdf), sfdf_pl);
}
static int
__mlxsw_sp_port_fdb_flush(const struct mlxsw_sp_port *mlxsw_sp_port)
{
int err, last_err = 0;
u16 vid;
for (vid = 1; vid < VLAN_N_VID - 1; vid++) {
err = mlxsw_sp_port_fdb_flush_by_port_fid(mlxsw_sp_port, vid);
if (err)
last_err = err;
}
return last_err;
}
static int
__mlxsw_sp_port_fdb_flush_lagged(const struct mlxsw_sp_port *mlxsw_sp_port)
{
int err, last_err = 0;
u16 vid;
for (vid = 1; vid < VLAN_N_VID - 1; vid++) {
err = mlxsw_sp_port_fdb_flush_by_lag_id_fid(mlxsw_sp_port, vid);
if (err)
last_err = err;
}
return last_err;
}
static int mlxsw_sp_port_fdb_flush(struct mlxsw_sp_port *mlxsw_sp_port)
{
if (!list_empty(&mlxsw_sp_port->vports_list))
if (mlxsw_sp_port->lagged)
return __mlxsw_sp_port_fdb_flush_lagged(mlxsw_sp_port);
else
return __mlxsw_sp_port_fdb_flush(mlxsw_sp_port);
else
if (mlxsw_sp_port->lagged)
return mlxsw_sp_port_fdb_flush_by_lag_id(mlxsw_sp_port);
else
return mlxsw_sp_port_fdb_flush_by_port(mlxsw_sp_port);
}
static int mlxsw_sp_vport_fdb_flush(struct mlxsw_sp_port *mlxsw_sp_vport)
{
u16 vfid = mlxsw_sp_vport_vfid_get(mlxsw_sp_vport);
u16 fid = mlxsw_sp_vfid_to_fid(vfid);
if (mlxsw_sp_vport->lagged)
return mlxsw_sp_port_fdb_flush_by_lag_id_fid(mlxsw_sp_vport,
fid);
else
return mlxsw_sp_port_fdb_flush_by_port_fid(mlxsw_sp_vport, fid);
}
static bool mlxsw_sp_port_dev_check(const struct net_device *dev)
{
return dev->netdev_ops == &mlxsw_sp_port_netdev_ops;
}
static int mlxsw_sp_port_bridge_join(struct mlxsw_sp_port *mlxsw_sp_port)
{
struct net_device *dev = mlxsw_sp_port->dev;
int err;
/* When port is not bridged untagged packets are tagged with
* PVID=VID=1, thereby creating an implicit VLAN interface in
* the device. Remove it and let bridge code take care of its
* own VLANs.
*/
err = mlxsw_sp_port_kill_vid(dev, 0, 1);
if (err)
return err;
mlxsw_sp_port->learning = 1;
mlxsw_sp_port->learning_sync = 1;
mlxsw_sp_port->uc_flood = 1;
mlxsw_sp_port->bridged = 1;
return 0;
}
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
static int mlxsw_sp_port_bridge_leave(struct mlxsw_sp_port *mlxsw_sp_port,
bool flush_fdb)
{
struct net_device *dev = mlxsw_sp_port->dev;
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
if (flush_fdb && mlxsw_sp_port_fdb_flush(mlxsw_sp_port))
netdev_err(mlxsw_sp_port->dev, "Failed to flush FDB\n");
mlxsw_sp_port_pvid_set(mlxsw_sp_port, 1);
mlxsw_sp_port->learning = 0;
mlxsw_sp_port->learning_sync = 0;
mlxsw_sp_port->uc_flood = 0;
mlxsw_sp_port->bridged = 0;
/* Add implicit VLAN interface in the device, so that untagged
* packets will be classified to the default vFID.
*/
return mlxsw_sp_port_add_vid(dev, 0, 1);
}
static bool mlxsw_sp_master_bridge_check(struct mlxsw_sp *mlxsw_sp,
struct net_device *br_dev)
{
return !mlxsw_sp->master_bridge.dev ||
mlxsw_sp->master_bridge.dev == br_dev;
}
static void mlxsw_sp_master_bridge_inc(struct mlxsw_sp *mlxsw_sp,
struct net_device *br_dev)
{
mlxsw_sp->master_bridge.dev = br_dev;
mlxsw_sp->master_bridge.ref_count++;
}
static void mlxsw_sp_master_bridge_dec(struct mlxsw_sp *mlxsw_sp,
struct net_device *br_dev)
{
if (--mlxsw_sp->master_bridge.ref_count == 0)
mlxsw_sp->master_bridge.dev = NULL;
}
static int mlxsw_sp_lag_create(struct mlxsw_sp *mlxsw_sp, u16 lag_id)
{
char sldr_pl[MLXSW_REG_SLDR_LEN];
mlxsw_reg_sldr_lag_create_pack(sldr_pl, lag_id);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sldr), sldr_pl);
}
static int mlxsw_sp_lag_destroy(struct mlxsw_sp *mlxsw_sp, u16 lag_id)
{
char sldr_pl[MLXSW_REG_SLDR_LEN];
mlxsw_reg_sldr_lag_destroy_pack(sldr_pl, lag_id);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sldr), sldr_pl);
}
static int mlxsw_sp_lag_col_port_add(struct mlxsw_sp_port *mlxsw_sp_port,
u16 lag_id, u8 port_index)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char slcor_pl[MLXSW_REG_SLCOR_LEN];
mlxsw_reg_slcor_port_add_pack(slcor_pl, mlxsw_sp_port->local_port,
lag_id, port_index);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(slcor), slcor_pl);
}
static int mlxsw_sp_lag_col_port_remove(struct mlxsw_sp_port *mlxsw_sp_port,
u16 lag_id)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char slcor_pl[MLXSW_REG_SLCOR_LEN];
mlxsw_reg_slcor_port_remove_pack(slcor_pl, mlxsw_sp_port->local_port,
lag_id);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(slcor), slcor_pl);
}
static int mlxsw_sp_lag_col_port_enable(struct mlxsw_sp_port *mlxsw_sp_port,
u16 lag_id)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char slcor_pl[MLXSW_REG_SLCOR_LEN];
mlxsw_reg_slcor_col_enable_pack(slcor_pl, mlxsw_sp_port->local_port,
lag_id);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(slcor), slcor_pl);
}
static int mlxsw_sp_lag_col_port_disable(struct mlxsw_sp_port *mlxsw_sp_port,
u16 lag_id)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char slcor_pl[MLXSW_REG_SLCOR_LEN];
mlxsw_reg_slcor_col_disable_pack(slcor_pl, mlxsw_sp_port->local_port,
lag_id);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(slcor), slcor_pl);
}
static int mlxsw_sp_lag_index_get(struct mlxsw_sp *mlxsw_sp,
struct net_device *lag_dev,
u16 *p_lag_id)
{
struct mlxsw_sp_upper *lag;
int free_lag_id = -1;
int i;
for (i = 0; i < MLXSW_SP_LAG_MAX; i++) {
lag = mlxsw_sp_lag_get(mlxsw_sp, i);
if (lag->ref_count) {
if (lag->dev == lag_dev) {
*p_lag_id = i;
return 0;
}
} else if (free_lag_id < 0) {
free_lag_id = i;
}
}
if (free_lag_id < 0)
return -EBUSY;
*p_lag_id = free_lag_id;
return 0;
}
static bool
mlxsw_sp_master_lag_check(struct mlxsw_sp *mlxsw_sp,
struct net_device *lag_dev,
struct netdev_lag_upper_info *lag_upper_info)
{
u16 lag_id;
if (mlxsw_sp_lag_index_get(mlxsw_sp, lag_dev, &lag_id) != 0)
return false;
if (lag_upper_info->tx_type != NETDEV_LAG_TX_TYPE_HASH)
return false;
return true;
}
static int mlxsw_sp_port_lag_index_get(struct mlxsw_sp *mlxsw_sp,
u16 lag_id, u8 *p_port_index)
{
int i;
for (i = 0; i < MLXSW_SP_PORT_PER_LAG_MAX; i++) {
if (!mlxsw_sp_port_lagged_get(mlxsw_sp, lag_id, i)) {
*p_port_index = i;
return 0;
}
}
return -EBUSY;
}
static int mlxsw_sp_port_lag_join(struct mlxsw_sp_port *mlxsw_sp_port,
struct net_device *lag_dev)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
struct mlxsw_sp_upper *lag;
u16 lag_id;
u8 port_index;
int err;
err = mlxsw_sp_lag_index_get(mlxsw_sp, lag_dev, &lag_id);
if (err)
return err;
lag = mlxsw_sp_lag_get(mlxsw_sp, lag_id);
if (!lag->ref_count) {
err = mlxsw_sp_lag_create(mlxsw_sp, lag_id);
if (err)
return err;
lag->dev = lag_dev;
}
err = mlxsw_sp_port_lag_index_get(mlxsw_sp, lag_id, &port_index);
if (err)
return err;
err = mlxsw_sp_lag_col_port_add(mlxsw_sp_port, lag_id, port_index);
if (err)
goto err_col_port_add;
err = mlxsw_sp_lag_col_port_enable(mlxsw_sp_port, lag_id);
if (err)
goto err_col_port_enable;
mlxsw_core_lag_mapping_set(mlxsw_sp->core, lag_id, port_index,
mlxsw_sp_port->local_port);
mlxsw_sp_port->lag_id = lag_id;
mlxsw_sp_port->lagged = 1;
lag->ref_count++;
return 0;
err_col_port_add:
if (!lag->ref_count)
mlxsw_sp_lag_destroy(mlxsw_sp, lag_id);
err_col_port_enable:
mlxsw_sp_lag_col_port_remove(mlxsw_sp_port, lag_id);
return err;
}
static int mlxsw_sp_vport_bridge_leave(struct mlxsw_sp_port *mlxsw_sp_vport,
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
struct net_device *br_dev,
bool flush_fdb);
static int mlxsw_sp_port_lag_leave(struct mlxsw_sp_port *mlxsw_sp_port,
struct net_device *lag_dev)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
struct mlxsw_sp_port *mlxsw_sp_vport;
struct mlxsw_sp_upper *lag;
u16 lag_id = mlxsw_sp_port->lag_id;
int err;
if (!mlxsw_sp_port->lagged)
return 0;
lag = mlxsw_sp_lag_get(mlxsw_sp, lag_id);
WARN_ON(lag->ref_count == 0);
err = mlxsw_sp_lag_col_port_disable(mlxsw_sp_port, lag_id);
if (err)
return err;
err = mlxsw_sp_lag_col_port_remove(mlxsw_sp_port, lag_id);
if (err)
return err;
/* In case we leave a LAG device that has bridges built on top,
* then their teardown sequence is never issued and we need to
* invoke the necessary cleanup routines ourselves.
*/
list_for_each_entry(mlxsw_sp_vport, &mlxsw_sp_port->vports_list,
vport.list) {
struct net_device *br_dev;
if (!mlxsw_sp_vport->bridged)
continue;
br_dev = mlxsw_sp_vport_br_get(mlxsw_sp_vport);
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
mlxsw_sp_vport_bridge_leave(mlxsw_sp_vport, br_dev, false);
}
if (mlxsw_sp_port->bridged) {
mlxsw_sp_port_active_vlans_del(mlxsw_sp_port);
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
mlxsw_sp_port_bridge_leave(mlxsw_sp_port, false);
mlxsw_sp_master_bridge_dec(mlxsw_sp, NULL);
}
if (lag->ref_count == 1) {
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
if (mlxsw_sp_port_fdb_flush_by_lag_id(mlxsw_sp_port))
netdev_err(mlxsw_sp_port->dev, "Failed to flush FDB\n");
err = mlxsw_sp_lag_destroy(mlxsw_sp, lag_id);
if (err)
return err;
}
mlxsw_core_lag_mapping_clear(mlxsw_sp->core, lag_id,
mlxsw_sp_port->local_port);
mlxsw_sp_port->lagged = 0;
lag->ref_count--;
return 0;
}
static int mlxsw_sp_lag_dist_port_add(struct mlxsw_sp_port *mlxsw_sp_port,
u16 lag_id)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char sldr_pl[MLXSW_REG_SLDR_LEN];
mlxsw_reg_sldr_lag_add_port_pack(sldr_pl, lag_id,
mlxsw_sp_port->local_port);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sldr), sldr_pl);
}
static int mlxsw_sp_lag_dist_port_remove(struct mlxsw_sp_port *mlxsw_sp_port,
u16 lag_id)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
char sldr_pl[MLXSW_REG_SLDR_LEN];
mlxsw_reg_sldr_lag_remove_port_pack(sldr_pl, lag_id,
mlxsw_sp_port->local_port);
return mlxsw_reg_write(mlxsw_sp->core, MLXSW_REG(sldr), sldr_pl);
}
static int mlxsw_sp_port_lag_tx_en_set(struct mlxsw_sp_port *mlxsw_sp_port,
bool lag_tx_enabled)
{
if (lag_tx_enabled)
return mlxsw_sp_lag_dist_port_add(mlxsw_sp_port,
mlxsw_sp_port->lag_id);
else
return mlxsw_sp_lag_dist_port_remove(mlxsw_sp_port,
mlxsw_sp_port->lag_id);
}
static int mlxsw_sp_port_lag_changed(struct mlxsw_sp_port *mlxsw_sp_port,
struct netdev_lag_lower_state_info *info)
{
return mlxsw_sp_port_lag_tx_en_set(mlxsw_sp_port, info->tx_enabled);
}
static int mlxsw_sp_port_vlan_link(struct mlxsw_sp_port *mlxsw_sp_port,
struct net_device *vlan_dev)
{
struct mlxsw_sp_port *mlxsw_sp_vport;
u16 vid = vlan_dev_vlan_id(vlan_dev);
mlxsw_sp_vport = mlxsw_sp_port_vport_find(mlxsw_sp_port, vid);
if (!mlxsw_sp_vport) {
WARN_ON(!mlxsw_sp_vport);
return -EINVAL;
}
mlxsw_sp_vport->dev = vlan_dev;
return 0;
}
static int mlxsw_sp_port_vlan_unlink(struct mlxsw_sp_port *mlxsw_sp_port,
struct net_device *vlan_dev)
{
struct mlxsw_sp_port *mlxsw_sp_vport;
u16 vid = vlan_dev_vlan_id(vlan_dev);
mlxsw_sp_vport = mlxsw_sp_port_vport_find(mlxsw_sp_port, vid);
if (!mlxsw_sp_vport) {
WARN_ON(!mlxsw_sp_vport);
return -EINVAL;
}
/* When removing a VLAN device while still bridged we should first
* remove it from the bridge, as we receive the bridge's notification
* when the vPort is already gone.
*/
if (mlxsw_sp_vport->bridged) {
struct net_device *br_dev;
br_dev = mlxsw_sp_vport_br_get(mlxsw_sp_vport);
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
mlxsw_sp_vport_bridge_leave(mlxsw_sp_vport, br_dev, true);
}
mlxsw_sp_vport->dev = mlxsw_sp_port->dev;
return 0;
}
static int mlxsw_sp_netdevice_port_upper_event(struct net_device *dev,
unsigned long event, void *ptr)
{
struct netdev_notifier_changeupper_info *info;
struct mlxsw_sp_port *mlxsw_sp_port;
struct net_device *upper_dev;
struct mlxsw_sp *mlxsw_sp;
int err;
mlxsw_sp_port = netdev_priv(dev);
mlxsw_sp = mlxsw_sp_port->mlxsw_sp;
info = ptr;
switch (event) {
case NETDEV_PRECHANGEUPPER:
upper_dev = info->upper_dev;
if (!info->master || !info->linking)
break;
/* HW limitation forbids to put ports to multiple bridges. */
if (netif_is_bridge_master(upper_dev) &&
!mlxsw_sp_master_bridge_check(mlxsw_sp, upper_dev))
return NOTIFY_BAD;
if (netif_is_lag_master(upper_dev) &&
!mlxsw_sp_master_lag_check(mlxsw_sp, upper_dev,
info->upper_info))
return NOTIFY_BAD;
break;
case NETDEV_CHANGEUPPER:
upper_dev = info->upper_dev;
if (is_vlan_dev(upper_dev)) {
if (info->linking) {
err = mlxsw_sp_port_vlan_link(mlxsw_sp_port,
upper_dev);
if (err) {
netdev_err(dev, "Failed to link VLAN device\n");
return NOTIFY_BAD;
}
} else {
err = mlxsw_sp_port_vlan_unlink(mlxsw_sp_port,
upper_dev);
if (err) {
netdev_err(dev, "Failed to unlink VLAN device\n");
return NOTIFY_BAD;
}
}
} else if (netif_is_bridge_master(upper_dev)) {
if (info->linking) {
err = mlxsw_sp_port_bridge_join(mlxsw_sp_port);
if (err) {
netdev_err(dev, "Failed to join bridge\n");
return NOTIFY_BAD;
}
mlxsw_sp_master_bridge_inc(mlxsw_sp, upper_dev);
} else {
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
err = mlxsw_sp_port_bridge_leave(mlxsw_sp_port,
true);
mlxsw_sp_master_bridge_dec(mlxsw_sp, upper_dev);
if (err) {
netdev_err(dev, "Failed to leave bridge\n");
return NOTIFY_BAD;
}
}
} else if (netif_is_lag_master(upper_dev)) {
if (info->linking) {
err = mlxsw_sp_port_lag_join(mlxsw_sp_port,
upper_dev);
if (err) {
netdev_err(dev, "Failed to join link aggregation\n");
return NOTIFY_BAD;
}
} else {
err = mlxsw_sp_port_lag_leave(mlxsw_sp_port,
upper_dev);
if (err) {
netdev_err(dev, "Failed to leave link aggregation\n");
return NOTIFY_BAD;
}
}
}
break;
}
return NOTIFY_DONE;
}
static int mlxsw_sp_netdevice_port_lower_event(struct net_device *dev,
unsigned long event, void *ptr)
{
struct netdev_notifier_changelowerstate_info *info;
struct mlxsw_sp_port *mlxsw_sp_port;
int err;
mlxsw_sp_port = netdev_priv(dev);
info = ptr;
switch (event) {
case NETDEV_CHANGELOWERSTATE:
if (netif_is_lag_port(dev) && mlxsw_sp_port->lagged) {
err = mlxsw_sp_port_lag_changed(mlxsw_sp_port,
info->lower_state_info);
if (err)
netdev_err(dev, "Failed to reflect link aggregation lower state change\n");
}
break;
}
return NOTIFY_DONE;
}
static int mlxsw_sp_netdevice_port_event(struct net_device *dev,
unsigned long event, void *ptr)
{
switch (event) {
case NETDEV_PRECHANGEUPPER:
case NETDEV_CHANGEUPPER:
return mlxsw_sp_netdevice_port_upper_event(dev, event, ptr);
case NETDEV_CHANGELOWERSTATE:
return mlxsw_sp_netdevice_port_lower_event(dev, event, ptr);
}
return NOTIFY_DONE;
}
static int mlxsw_sp_netdevice_lag_event(struct net_device *lag_dev,
unsigned long event, void *ptr)
{
struct net_device *dev;
struct list_head *iter;
int ret;
netdev_for_each_lower_dev(lag_dev, dev, iter) {
if (mlxsw_sp_port_dev_check(dev)) {
ret = mlxsw_sp_netdevice_port_event(dev, event, ptr);
if (ret == NOTIFY_BAD)
return ret;
}
}
return NOTIFY_DONE;
}
static struct mlxsw_sp_vfid *
mlxsw_sp_br_vfid_find(const struct mlxsw_sp *mlxsw_sp,
const struct net_device *br_dev)
{
struct mlxsw_sp_vfid *vfid;
list_for_each_entry(vfid, &mlxsw_sp->br_vfids.list, list) {
if (vfid->br_dev == br_dev)
return vfid;
}
return NULL;
}
static u16 mlxsw_sp_vfid_to_br_vfid(u16 vfid)
{
return vfid - MLXSW_SP_VFID_PORT_MAX;
}
static u16 mlxsw_sp_br_vfid_to_vfid(u16 br_vfid)
{
return MLXSW_SP_VFID_PORT_MAX + br_vfid;
}
static u16 mlxsw_sp_avail_br_vfid_get(const struct mlxsw_sp *mlxsw_sp)
{
return find_first_zero_bit(mlxsw_sp->br_vfids.mapped,
MLXSW_SP_VFID_BR_MAX);
}
static struct mlxsw_sp_vfid *mlxsw_sp_br_vfid_create(struct mlxsw_sp *mlxsw_sp,
struct net_device *br_dev)
{
struct device *dev = mlxsw_sp->bus_info->dev;
struct mlxsw_sp_vfid *vfid;
u16 n_vfid;
int err;
n_vfid = mlxsw_sp_br_vfid_to_vfid(mlxsw_sp_avail_br_vfid_get(mlxsw_sp));
if (n_vfid == MLXSW_SP_VFID_MAX) {
dev_err(dev, "No available vFIDs\n");
return ERR_PTR(-ERANGE);
}
err = __mlxsw_sp_vfid_create(mlxsw_sp, n_vfid);
if (err) {
dev_err(dev, "Failed to create vFID=%d\n", n_vfid);
return ERR_PTR(err);
}
vfid = kzalloc(sizeof(*vfid), GFP_KERNEL);
if (!vfid)
goto err_allocate_vfid;
vfid->vfid = n_vfid;
vfid->br_dev = br_dev;
list_add(&vfid->list, &mlxsw_sp->br_vfids.list);
set_bit(mlxsw_sp_vfid_to_br_vfid(n_vfid), mlxsw_sp->br_vfids.mapped);
return vfid;
err_allocate_vfid:
__mlxsw_sp_vfid_destroy(mlxsw_sp, n_vfid);
return ERR_PTR(-ENOMEM);
}
static void mlxsw_sp_br_vfid_destroy(struct mlxsw_sp *mlxsw_sp,
struct mlxsw_sp_vfid *vfid)
{
u16 br_vfid = mlxsw_sp_vfid_to_br_vfid(vfid->vfid);
clear_bit(br_vfid, mlxsw_sp->br_vfids.mapped);
list_del(&vfid->list);
__mlxsw_sp_vfid_destroy(mlxsw_sp, vfid->vfid);
kfree(vfid);
}
static int mlxsw_sp_vport_bridge_leave(struct mlxsw_sp_port *mlxsw_sp_vport,
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
struct net_device *br_dev,
bool flush_fdb)
{
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_vport->mlxsw_sp;
u16 vid = mlxsw_sp_vport_vid_get(mlxsw_sp_vport);
struct net_device *dev = mlxsw_sp_vport->dev;
struct mlxsw_sp_vfid *vfid, *new_vfid;
int err;
vfid = mlxsw_sp_br_vfid_find(mlxsw_sp, br_dev);
if (!vfid) {
WARN_ON(!vfid);
return -EINVAL;
}
/* We need a vFID to go back to after leaving the bridge's vFID. */
new_vfid = mlxsw_sp_vfid_find(mlxsw_sp, vid);
if (!new_vfid) {
new_vfid = mlxsw_sp_vfid_create(mlxsw_sp, vid);
if (IS_ERR(new_vfid)) {
netdev_err(dev, "Failed to create vFID for VID=%d\n",
vid);
return PTR_ERR(new_vfid);
}
}
/* Invalidate existing {Port, VID} to vFID mapping and create a new
* one for the new vFID.
*/
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID,
false,
mlxsw_sp_vfid_to_fid(vfid->vfid),
vid);
if (err) {
netdev_err(dev, "Failed to invalidate {Port, VID} to vFID=%d mapping\n",
vfid->vfid);
goto err_port_vid_to_fid_invalidate;
}
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID,
true,
mlxsw_sp_vfid_to_fid(new_vfid->vfid),
vid);
if (err) {
netdev_err(dev, "Failed to map {Port, VID} to vFID=%d\n",
new_vfid->vfid);
goto err_port_vid_to_fid_validate;
}
err = mlxsw_sp_port_vid_learning_set(mlxsw_sp_vport, vid, false);
if (err) {
netdev_err(dev, "Failed to disable learning\n");
goto err_port_vid_learning_set;
}
err = mlxsw_sp_vport_flood_set(mlxsw_sp_vport, vfid->vfid, false,
false);
if (err) {
netdev_err(dev, "Failed clear to clear flooding\n");
goto err_vport_flood_set;
}
err = mlxsw_sp_port_stp_state_set(mlxsw_sp_vport, vid,
MLXSW_REG_SPMS_STATE_FORWARDING);
if (err) {
netdev_err(dev, "Failed to set STP state\n");
goto err_port_stp_state_set;
}
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
if (flush_fdb && mlxsw_sp_vport_fdb_flush(mlxsw_sp_vport))
netdev_err(dev, "Failed to flush FDB\n");
/* Switch between the vFIDs and destroy the old one if needed. */
new_vfid->nr_vports++;
mlxsw_sp_vport->vport.vfid = new_vfid;
vfid->nr_vports--;
if (!vfid->nr_vports)
mlxsw_sp_br_vfid_destroy(mlxsw_sp, vfid);
mlxsw_sp_vport->learning = 0;
mlxsw_sp_vport->learning_sync = 0;
mlxsw_sp_vport->uc_flood = 0;
mlxsw_sp_vport->bridged = 0;
return 0;
err_port_stp_state_set:
err_vport_flood_set:
err_port_vid_learning_set:
err_port_vid_to_fid_validate:
err_port_vid_to_fid_invalidate:
/* Rollback vFID only if new. */
if (!new_vfid->nr_vports)
mlxsw_sp_vfid_destroy(mlxsw_sp, new_vfid);
return err;
}
static int mlxsw_sp_vport_bridge_join(struct mlxsw_sp_port *mlxsw_sp_vport,
struct net_device *br_dev)
{
struct mlxsw_sp_vfid *old_vfid = mlxsw_sp_vport->vport.vfid;
struct mlxsw_sp *mlxsw_sp = mlxsw_sp_vport->mlxsw_sp;
u16 vid = mlxsw_sp_vport_vid_get(mlxsw_sp_vport);
struct net_device *dev = mlxsw_sp_vport->dev;
struct mlxsw_sp_vfid *vfid;
int err;
vfid = mlxsw_sp_br_vfid_find(mlxsw_sp, br_dev);
if (!vfid) {
vfid = mlxsw_sp_br_vfid_create(mlxsw_sp, br_dev);
if (IS_ERR(vfid)) {
netdev_err(dev, "Failed to create bridge vFID\n");
return PTR_ERR(vfid);
}
}
err = mlxsw_sp_vport_flood_set(mlxsw_sp_vport, vfid->vfid, true, false);
if (err) {
netdev_err(dev, "Failed to setup flooding for vFID=%d\n",
vfid->vfid);
goto err_port_flood_set;
}
err = mlxsw_sp_port_vid_learning_set(mlxsw_sp_vport, vid, true);
if (err) {
netdev_err(dev, "Failed to enable learning\n");
goto err_port_vid_learning_set;
}
/* We need to invalidate existing {Port, VID} to vFID mapping and
* create a new one for the bridge's vFID.
*/
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID,
false,
mlxsw_sp_vfid_to_fid(old_vfid->vfid),
vid);
if (err) {
netdev_err(dev, "Failed to invalidate {Port, VID} to vFID=%d mapping\n",
old_vfid->vfid);
goto err_port_vid_to_fid_invalidate;
}
err = mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID,
true,
mlxsw_sp_vfid_to_fid(vfid->vfid),
vid);
if (err) {
netdev_err(dev, "Failed to map {Port, VID} to vFID=%d\n",
vfid->vfid);
goto err_port_vid_to_fid_validate;
}
/* Switch between the vFIDs and destroy the old one if needed. */
vfid->nr_vports++;
mlxsw_sp_vport->vport.vfid = vfid;
old_vfid->nr_vports--;
if (!old_vfid->nr_vports)
mlxsw_sp_vfid_destroy(mlxsw_sp, old_vfid);
mlxsw_sp_vport->learning = 1;
mlxsw_sp_vport->learning_sync = 1;
mlxsw_sp_vport->uc_flood = 1;
mlxsw_sp_vport->bridged = 1;
return 0;
err_port_vid_to_fid_validate:
mlxsw_sp_port_vid_to_fid_set(mlxsw_sp_vport,
MLXSW_REG_SVFA_MT_PORT_VID_TO_FID, false,
mlxsw_sp_vfid_to_fid(old_vfid->vfid), vid);
err_port_vid_to_fid_invalidate:
mlxsw_sp_port_vid_learning_set(mlxsw_sp_vport, vid, false);
err_port_vid_learning_set:
mlxsw_sp_vport_flood_set(mlxsw_sp_vport, vfid->vfid, false, false);
err_port_flood_set:
if (!vfid->nr_vports)
mlxsw_sp_br_vfid_destroy(mlxsw_sp, vfid);
return err;
}
static bool
mlxsw_sp_port_master_bridge_check(const struct mlxsw_sp_port *mlxsw_sp_port,
const struct net_device *br_dev)
{
struct mlxsw_sp_port *mlxsw_sp_vport;
list_for_each_entry(mlxsw_sp_vport, &mlxsw_sp_port->vports_list,
vport.list) {
if (mlxsw_sp_vport_br_get(mlxsw_sp_vport) == br_dev)
return false;
}
return true;
}
static int mlxsw_sp_netdevice_vport_event(struct net_device *dev,
unsigned long event, void *ptr,
u16 vid)
{
struct mlxsw_sp_port *mlxsw_sp_port = netdev_priv(dev);
struct netdev_notifier_changeupper_info *info = ptr;
struct mlxsw_sp_port *mlxsw_sp_vport;
struct net_device *upper_dev;
int err;
mlxsw_sp_vport = mlxsw_sp_port_vport_find(mlxsw_sp_port, vid);
switch (event) {
case NETDEV_PRECHANGEUPPER:
upper_dev = info->upper_dev;
if (!info->master || !info->linking)
break;
if (!netif_is_bridge_master(upper_dev))
return NOTIFY_BAD;
/* We can't have multiple VLAN interfaces configured on
* the same port and being members in the same bridge.
*/
if (!mlxsw_sp_port_master_bridge_check(mlxsw_sp_port,
upper_dev))
return NOTIFY_BAD;
break;
case NETDEV_CHANGEUPPER:
upper_dev = info->upper_dev;
if (!info->master)
break;
if (info->linking) {
if (!mlxsw_sp_vport) {
WARN_ON(!mlxsw_sp_vport);
return NOTIFY_BAD;
}
err = mlxsw_sp_vport_bridge_join(mlxsw_sp_vport,
upper_dev);
if (err) {
netdev_err(dev, "Failed to join bridge\n");
return NOTIFY_BAD;
}
} else {
/* We ignore bridge's unlinking notifications if vPort
* is gone, since we already left the bridge when the
* VLAN device was unlinked from the real device.
*/
if (!mlxsw_sp_vport)
return NOTIFY_DONE;
err = mlxsw_sp_vport_bridge_leave(mlxsw_sp_vport,
mlxsw: spectrum: Flush FDB when leaving bridge As explained in previous commit, we should always take care of flushing the FDB in the driver and not rely on bridge code. We need to distinguish between two cases with regards to LAG: 1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of it). In this case don't flush the FDB entries pointing to the LAG ID, as this will affect other ports still member in the LAG. Only flush the FDB when the last port in the LAG is leaving the bridge. 2) LAG device is leaving the bridge. In this case the CHANGEUPPER event is simply propagated to each member port, so make each port flush the FDB in its turn. Note that emptying a bridged LAG from ports creates an inconsistency between hardware and software. A user who later (< ageing_time) re-populates the LAG won't have any FDB entries pointing to the LAG ID in hardware, but they will be present in the software bridge's FDB. Currently there is no good solution to this problem, but this will be addressed by us in the future. In order to optimize the flushing process, flush by port or LAG ID if there are no VLAN interfaces on top of the port. Otherwise, flush using (Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to which the VLAN device is mapped to. Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-01-27 21:20:18 +07:00
upper_dev, true);
if (err) {
netdev_err(dev, "Failed to leave bridge\n");
return NOTIFY_BAD;
}
}
}
return NOTIFY_DONE;
}
static int mlxsw_sp_netdevice_lag_vport_event(struct net_device *lag_dev,
unsigned long event, void *ptr,
u16 vid)
{
struct net_device *dev;
struct list_head *iter;
int ret;
netdev_for_each_lower_dev(lag_dev, dev, iter) {
if (mlxsw_sp_port_dev_check(dev)) {
ret = mlxsw_sp_netdevice_vport_event(dev, event, ptr,
vid);
if (ret == NOTIFY_BAD)
return ret;
}
}
return NOTIFY_DONE;
}
static int mlxsw_sp_netdevice_vlan_event(struct net_device *vlan_dev,
unsigned long event, void *ptr)
{
struct net_device *real_dev = vlan_dev_real_dev(vlan_dev);
u16 vid = vlan_dev_vlan_id(vlan_dev);
if (mlxsw_sp_port_dev_check(real_dev))
return mlxsw_sp_netdevice_vport_event(real_dev, event, ptr,
vid);
else if (netif_is_lag_master(real_dev))
return mlxsw_sp_netdevice_lag_vport_event(real_dev, event, ptr,
vid);
return NOTIFY_DONE;
}
static int mlxsw_sp_netdevice_event(struct notifier_block *unused,
unsigned long event, void *ptr)
{
struct net_device *dev = netdev_notifier_info_to_dev(ptr);
if (mlxsw_sp_port_dev_check(dev))
return mlxsw_sp_netdevice_port_event(dev, event, ptr);
if (netif_is_lag_master(dev))
return mlxsw_sp_netdevice_lag_event(dev, event, ptr);
if (is_vlan_dev(dev))
return mlxsw_sp_netdevice_vlan_event(dev, event, ptr);
return NOTIFY_DONE;
}
static struct notifier_block mlxsw_sp_netdevice_nb __read_mostly = {
.notifier_call = mlxsw_sp_netdevice_event,
};
static int __init mlxsw_sp_module_init(void)
{
int err;
register_netdevice_notifier(&mlxsw_sp_netdevice_nb);
err = mlxsw_core_driver_register(&mlxsw_sp_driver);
if (err)
goto err_core_driver_register;
return 0;
err_core_driver_register:
unregister_netdevice_notifier(&mlxsw_sp_netdevice_nb);
return err;
}
static void __exit mlxsw_sp_module_exit(void)
{
mlxsw_core_driver_unregister(&mlxsw_sp_driver);
unregister_netdevice_notifier(&mlxsw_sp_netdevice_nb);
}
module_init(mlxsw_sp_module_init);
module_exit(mlxsw_sp_module_exit);
MODULE_LICENSE("Dual BSD/GPL");
MODULE_AUTHOR("Jiri Pirko <jiri@mellanox.com>");
MODULE_DESCRIPTION("Mellanox Spectrum driver");
MODULE_MLXSW_DRIVER_ALIAS(MLXSW_DEVICE_KIND_SPECTRUM);