linux_dsm_epyc7002/arch/arm/boot/dts/omap3-overo-base.dtsi

/*
 * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

/*
 * The Gumstix Overo must be combined with an expansion board.
 */

/ {
	pwmleds {
		compatible = "pwm-leds";

		overo {
			label = "overo:blue:COM";
			pwms = <&twl_pwmled 1 7812500>;
			max-brightness = <127>;
			linux,default-trigger = "mmc0";
		};
	};

	sound {
		compatible = "ti,omap-twl4030";
		ti,model = "overo";

		ti,mcbsp = <&mcbsp2>;
		ti,codec = <&twl_audio>;
	};

	/* HS USB Port 2 Power */
	hsusb2_power: hsusb2_power_reg {
		compatible = "regulator-fixed";
		regulator-name = "hsusb2_vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		gpio = <&gpio6 8 0>;				/* gpio_168: vbus enable */
		startup-delay-us = <70000>;
		enable-active-high;
	};

	/* HS USB Host PHY on PORT 2 */
	hsusb2_phy: hsusb2_phy {
		compatible = "usb-nop-xceiv";
		reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;	/* gpio_183 */
		vcc-supply = <&hsusb2_power>;
	};

	/* Regulator to trigger the nPoweron signal of the Wifi module */
	w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
		compatible = "regulator-fixed";
		regulator-name = "regulator-w3cbw003c-npoweron";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>;		/* gpio_54: nPoweron */
		enable-active-high;
	};

	/* Regulator to trigger the nReset signal of the Wifi module */
	w3cbw003c_wifi_nreset: regulator-w3cbw003c-wifi-nreset {
		pinctrl-names = "default";
		pinctrl-0 = <&w3cbw003c_pins &w3cbw003c_2_pins>;
		compatible = "regulator-fixed";
		regulator-name = "regulator-w3cbw003c-wifi-nreset";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>;		/* gpio_16: WiFi nReset */
		startup-delay-us = <10000>;
	};

	/* Regulator to trigger the nReset signal of the Bluetooth module */
	w3cbw003c_bt_nreset: regulator-w3cbw003c-bt-nreset {
		compatible = "regulator-fixed";
		regulator-name = "regulator-w3cbw003c-bt-nreset";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;		/* gpio_164: BT nReset */
		startup-delay-us = <10000>;
	};
};

&omap3_pmx_core {
	pinctrl-names = "default";
	pinctrl-0 = <
			&hsusb2_pins
	>;

	uart2_pins: pinmux_uart2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1)	/* mcbsp3_dx.uart2_cts */
			OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1)	/* mcbsp3_dr.uart2_rts */
			OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1)	/* mcbsp3_clk.uart2_tx */
			OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1)	/* mcbsp3_fsx.uart2_rx */
		>;
	};

	i2c1_pins: pinmux_i2c1_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)		/* i2c1_scl.i2c1_scl */
			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)		/* i2c1_sda.i2c1_sda */
		>;
	};

	mmc1_pins: pinmux_mmc1_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_clk.sdmmc1_clk */
			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_cmd.sdmmc1_cmd */
			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat0.sdmmc1_dat0 */
			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat1.sdmmc1_dat1 */
			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat2.sdmmc1_dat2 */
			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc1_dat3.sdmmc1_dat3 */
		>;
	};

	mmc2_pins: pinmux_mmc2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat0.sdmmc2_dat0 */
			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat1.sdmmc2_dat1 */
			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat2.sdmmc2_dat2 */
			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat3.sdmmc2_dat3 */
		>;
	};

	/* WiFi/BT combo */
	w3cbw003c_pins: pinmux_w3cbw003c_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4)		/* gpmc_ncs3.gpio_54 */
			OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)		/* uart3_rts_sd.gpio_164 */
		>;
	};

	hsusb2_pins: pinmux_hsusb2_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
			OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4)		/* i2c2_scl.gpio_168 */
			OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4)		/* i2c2_sda.gpio_183 */
		>;
	};
};

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_pins>;
	clock-frequency = <2600000>;

	twl: twl@48 {
		reg = <0x48>;
		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
		interrupt-parent = <&intc>;

		twl_audio: audio {
			compatible = "ti,twl4030-audio";
			codec {
			};
		};
	};
};

#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"

/* i2c2 pins are used for gpio */
&i2c2 {
	status = "disabled";
};

/* on board microSD slot */
&mmc1 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;
	vmmc-supply = <&vmmc1>;
	bus-width = <4>;
};

/* optional on board WiFi */
&mmc2 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc2_pins>;
	vmmc-supply = <&w3cbw003c_npoweron>;
	vqmmc-supply = <&w3cbw003c_bt_nreset>;
	vmmc_aux-supply = <&w3cbw003c_wifi_nreset>;
	bus-width = <4>;
	cap-sdio-irq;
	non-removable;
};

&twl_gpio {
	ti,use-leds;
};

&usb_otg_hs {
	interface-type = <0>;
	usb-phy = <&usb2_phy>;
	phys = <&usb2_phy>;
	phy-names = "usb2-phy";
	mode = <3>;
	power = <50>;
};

&usbhshost {
	port2-mode = "ehci-phy";
};

&usbhsehci {
	phys = <0 &hsusb2_phy>;
};

&uart2 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
};