linux_dsm_epyc7002/arch/arm/boot/dts/rv1108.dtsi

942 lines
22 KiB
Plaintext
Raw Normal View History

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/rv1108-cru.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/thermal/thermal.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
compatible = "rockchip,rv1108";
interrupt-parent = <&gic>;
aliases {
i2c0 = &i2c0;
i2c1 = &i2c1;
i2c2 = &i2c2;
i2c3 = &i2c3;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@f00 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0xf00>;
clock-latency = <40000>;
clocks = <&cru ARMCLK>;
#cooling-cells = <2>; /* min followed by max */
dynamic-power-coefficient = <75>;
operating-points-v2 = <&cpu_opp_table>;
};
};
cpu_opp_table: opp_table {
compatible = "operating-points-v2";
opp-408000000 {
opp-hz = /bits/ 64 <408000000>;
opp-microvolt = <975000>;
clock-latency-ns = <40000>;
};
opp-600000000 {
opp-hz = /bits/ 64 <600000000>;
opp-microvolt = <975000>;
clock-latency-ns = <40000>;
};
opp-816000000 {
opp-hz = /bits/ 64 <816000000>;
opp-microvolt = <1025000>;
clock-latency-ns = <40000>;
};
opp-1008000000 {
opp-hz = /bits/ 64 <1008000000>;
opp-microvolt = <1150000>;
clock-latency-ns = <40000>;
};
};
arm-pmu {
compatible = "arm,cortex-a7-pmu";
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
};
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
arm,cpu-registers-not-fw-configured;
clock-frequency = <24000000>;
};
xin24m: oscillator {
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "xin24m";
#clock-cells = <0>;
};
amba {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
pdma: pdma@102a0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x102a0000 0x4000>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
arm,pl330-broken-no-flushp;
clocks = <&cru ACLK_DMAC>;
clock-names = "apb_pclk";
};
};
bus_intmem@10080000 {
compatible = "mmio-sram";
reg = <0x10080000 0x2000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0x10080000 0x2000>;
};
uart2: serial@10210000 {
compatible = "rockchip,rv1108-uart", "snps,dw-apb-uart";
reg = <0x10210000 0x100>;
interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clock-frequency = <24000000>;
clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
clock-names = "baudclk", "apb_pclk";
dmas = <&pdma 6>, <&pdma 7>;
#dma-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&uart2m0_xfer>;
status = "disabled";
};
uart1: serial@10220000 {
compatible = "rockchip,rv1108-uart", "snps,dw-apb-uart";
reg = <0x10220000 0x100>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clock-frequency = <24000000>;
clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
clock-names = "baudclk", "apb_pclk";
dmas = <&pdma 4>, <&pdma 5>;
#dma-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&uart1_xfer>;
status = "disabled";
};
uart0: serial@10230000 {
compatible = "rockchip,rv1108-uart", "snps,dw-apb-uart";
reg = <0x10230000 0x100>;
interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clock-frequency = <24000000>;
clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
clock-names = "baudclk", "apb_pclk";
dmas = <&pdma 2>, <&pdma 3>;
#dma-cells = <2>;
pinctrl-names = "default";
pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
status = "disabled";
};
i2c1: i2c@10240000 {
compatible = "rockchip,rv1108-i2c";
reg = <0x10240000 0x1000>;
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>;
clock-names = "i2c", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_xfer>;
rockchip,grf = <&grf>;
status = "disabled";
};
i2c2: i2c@10250000 {
compatible = "rockchip,rv1108-i2c";
reg = <0x10250000 0x1000>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>;
clock-names = "i2c", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&i2c2m1_xfer>;
rockchip,grf = <&grf>;
status = "disabled";
};
i2c3: i2c@10260000 {
compatible = "rockchip,rv1108-i2c";
reg = <0x10260000 0x1000>;
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>;
clock-names = "i2c", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&i2c3_xfer>;
rockchip,grf = <&grf>;
status = "disabled";
};
spi: spi@10270000 {
compatible = "rockchip,rv1108-spi";
reg = <0x10270000 0x1000>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_SPI>, <&cru PCLK_SPI>;
clock-names = "spiclk", "apb_pclk";
dmas = <&pdma 8>, <&pdma 9>;
dma-names = "tx", "rx";
#dma-cells = <2>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
pwm4: pwm@10280000 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x10280000 0x10>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm4_pin>;
#pwm-cells = <3>;
status = "disabled";
};
pwm5: pwm@10280010 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x10280010 0x10>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm5_pin>;
#pwm-cells = <3>;
status = "disabled";
};
pwm6: pwm@10280020 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x10280020 0x10>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm6_pin>;
#pwm-cells = <3>;
status = "disabled";
};
pwm7: pwm@10280030 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x10280030 0x10>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM>, <&cru PCLK_PWM>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm7_pin>;
#pwm-cells = <3>;
status = "disabled";
};
grf: syscon@10300000 {
compatible = "rockchip,rv1108-grf", "syscon", "simple-mfd";
reg = <0x10300000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
u2phy: usb2-phy@100 {
compatible = "rockchip,rv1108-usb2phy";
reg = <0x100 0x0c>;
clocks = <&cru SCLK_USBPHY>;
clock-names = "phyclk";
#clock-cells = <0>;
clock-output-names = "usbphy";
rockchip,usbgrf = <&usbgrf>;
status = "disabled";
u2phy_otg: otg-port {
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "otg-mux";
#phy-cells = <0>;
status = "disabled";
};
u2phy_host: host-port {
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "linestate";
#phy-cells = <0>;
status = "disabled";
};
};
};
timer: timer@10350000 {
compatible = "rockchip,rv1108-timer", "rockchip,rk3288-timer";
reg = <0x10350000 0x20>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&xin24m>, <&cru PCLK_TIMER>;
clock-names = "timer", "pclk";
};
watchdog: wdt@10360000 {
compatible = "snps,dw-wdt";
reg = <0x10360000 0x100>;
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru PCLK_WDT>;
clock-names = "pclk_wdt";
status = "disabled";
};
thermal-zones {
soc_thermal: soc-thermal {
polling-delay-passive = <20>;
polling-delay = <1000>;
sustainable-power = <50>;
thermal-sensors = <&tsadc 0>;
trips {
threshold: trip-point0 {
temperature = <70000>;
hysteresis = <2000>;
type = "passive";
};
target: trip-point1 {
temperature = <85000>;
hysteresis = <2000>;
type = "passive";
};
soc_crit: soc-crit {
temperature = <95000>;
hysteresis = <2000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&target>;
cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
contribution = <4096>;
};
};
};
};
tsadc: tsadc@10370000 {
compatible = "rockchip,rv1108-tsadc";
reg = <0x10370000 0x100>;
interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
assigned-clocks = <&cru SCLK_TSADC>;
assigned-clock-rates = <750000>;
clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
clock-names = "tsadc", "apb_pclk";
pinctrl-names = "init", "default", "sleep";
pinctrl-0 = <&otp_gpio>;
pinctrl-1 = <&otp_out>;
pinctrl-2 = <&otp_gpio>;
resets = <&cru SRST_TSADC>;
reset-names = "tsadc-apb";
rockchip,hw-tshut-temp = <120000>;
#thermal-sensor-cells = <1>;
status = "disabled";
};
adc: adc@1038c000 {
compatible = "rockchip,rv1108-saradc", "rockchip,rk3399-saradc";
reg = <0x1038c000 0x100>;
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
#io-channel-cells = <1>;
clock-frequency = <1000000>;
clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
clock-names = "saradc", "apb_pclk";
status = "disabled";
};
i2c0: i2c@20000000 {
compatible = "rockchip,rv1108-i2c";
reg = <0x20000000 0x1000>;
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&cru SCLK_I2C0_PMU>, <&cru PCLK_I2C0_PMU>;
clock-names = "i2c", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&i2c0_xfer>;
rockchip,grf = <&grf>;
status = "disabled";
};
pwm0: pwm@20040000 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x20040000 0x10>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm0_pin>;
#pwm-cells = <3>;
status = "disabled";
};
pwm1: pwm@20040010 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x20040010 0x10>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm1_pin>;
#pwm-cells = <3>;
status = "disabled";
};
pwm2: pwm@20040020 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x20040020 0x10>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm2_pin>;
#pwm-cells = <3>;
status = "disabled";
};
pwm3: pwm@20040030 {
compatible = "rockchip,rv1108-pwm", "rockchip,rk3288-pwm";
reg = <0x20040030 0x10>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_PWM0_PMU>, <&cru PCLK_PWM0_PMU>;
clock-names = "pwm", "pclk";
pinctrl-names = "default";
pinctrl-0 = <&pwm3_pin>;
#pwm-cells = <3>;
status = "disabled";
};
pmugrf: syscon@20060000 {
compatible = "rockchip,rv1108-pmugrf", "syscon";
reg = <0x20060000 0x1000>;
};
usbgrf: syscon@202a0000 {
compatible = "rockchip,rv1108-usbgrf", "syscon";
reg = <0x202a0000 0x1000>;
};
cru: clock-controller@20200000 {
compatible = "rockchip,rv1108-cru";
reg = <0x20200000 0x1000>;
rockchip,grf = <&grf>;
#clock-cells = <1>;
#reset-cells = <1>;
};
emmc: mmc@30110000 {
compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x30110000 0x4000>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
<&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
max-frequency = <150000000>;
status = "disabled";
};
sdio: mmc@30120000 {
compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x30120000 0x4000>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
<&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
max-frequency = <150000000>;
status = "disabled";
};
sdmmc: mmc@30130000 {
compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc";
reg = <0x30130000 0x4000>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
<&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
fifo-depth = <0x100>;
max-frequency = <100000000>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
status = "disabled";
};
usb_host_ehci: usb@30140000 {
compatible = "generic-ehci";
reg = <0x30140000 0x20000>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_HOST0>, <&u2phy>;
clock-names = "usbhost", "utmi";
phys = <&u2phy_host>;
phy-names = "usb";
status = "disabled";
};
usb_host_ohci: usb@30160000 {
compatible = "generic-ohci";
reg = <0x30160000 0x20000>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_HOST0>, <&u2phy>;
clock-names = "usbhost", "utmi";
phys = <&u2phy_host>;
phy-names = "usb";
status = "disabled";
};
usb_otg: usb@30180000 {
compatible = "rockchip,rv1108-usb", "rockchip,rk3066-usb",
"snps,dwc2";
reg = <0x30180000 0x40000>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru HCLK_OTG>;
clock-names = "otg";
dr_mode = "otg";
g-np-tx-fifo-size = <16>;
g-rx-fifo-size = <280>;
g-tx-fifo-size = <256 128 128 64 32 16>;
g-use-dma;
phys = <&u2phy_otg>;
phy-names = "usb2-phy";
status = "disabled";
};
gmac: eth@30200000 {
compatible = "rockchip,rv1108-gmac";
reg = <0x30200000 0x10000>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq", "eth_wake_irq";
clocks = <&cru SCLK_MAC>,
<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_RX>,
<&cru SCLK_MAC_REF>, <&cru SCLK_MAC_REFOUT>,
<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
clock-names = "stmmaceth",
"mac_clk_rx", "mac_clk_tx",
"clk_mac_ref", "clk_mac_refout",
"aclk_mac", "pclk_mac";
/* rv1108 only supports an rmii interface */
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&rmii_pins>;
rockchip,grf = <&grf>;
status = "disabled";
};
gic: interrupt-controller@32010000 {
compatible = "arm,gic-400";
interrupt-controller;
#interrupt-cells = <3>;
#address-cells = <0>;
reg = <0x32011000 0x1000>,
<0x32012000 0x2000>,
<0x32014000 0x2000>,
<0x32016000 0x2000>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
};
pinctrl: pinctrl {
compatible = "rockchip,rv1108-pinctrl";
rockchip,grf = <&grf>;
rockchip,pmu = <&pmugrf>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
gpio0: gpio0@20030000 {
compatible = "rockchip,gpio-bank";
reg = <0x20030000 0x100>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru PCLK_GPIO0_PMU>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio1: gpio1@10310000 {
compatible = "rockchip,gpio-bank";
reg = <0x10310000 0x100>;
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru PCLK_GPIO1>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio2: gpio2@10320000 {
compatible = "rockchip,gpio-bank";
reg = <0x10320000 0x100>;
interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru PCLK_GPIO2>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio3: gpio3@10330000 {
compatible = "rockchip,gpio-bank";
reg = <0x10330000 0x100>;
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru PCLK_GPIO3>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
pcfg_pull_up: pcfg-pull-up {
bias-pull-up;
};
pcfg_pull_down: pcfg-pull-down {
bias-pull-down;
};
pcfg_pull_none: pcfg-pull-none {
bias-disable;
};
pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
drive-strength = <8>;
};
pcfg_pull_none_drv_12ma: pcfg-pull-none-drv-12ma {
drive-strength = <12>;
};
pcfg_pull_none_smt: pcfg-pull-none-smt {
bias-disable;
input-schmitt-enable;
};
pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
bias-pull-up;
drive-strength = <8>;
};
pcfg_pull_none_drv_4ma: pcfg-pull-none-drv-4ma {
drive-strength = <4>;
};
pcfg_pull_up_drv_4ma: pcfg-pull-up-drv-4ma {
bias-pull-up;
drive-strength = <4>;
};
pcfg_output_high: pcfg-output-high {
output-high;
};
pcfg_output_low: pcfg-output-low {
output-low;
};
pcfg_input_high: pcfg-input-high {
bias-pull-up;
input-enable;
};
emmc {
emmc_bus8: emmc-bus8 {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <2 RK_PA0 2 &pcfg_pull_up_drv_8ma>,
<2 RK_PA1 2 &pcfg_pull_up_drv_8ma>,
<2 RK_PA2 2 &pcfg_pull_up_drv_8ma>,
<2 RK_PA3 2 &pcfg_pull_up_drv_8ma>,
<2 RK_PA4 2 &pcfg_pull_up_drv_8ma>,
<2 RK_PA5 2 &pcfg_pull_up_drv_8ma>,
<2 RK_PA6 2 &pcfg_pull_up_drv_8ma>,
<2 RK_PA7 2 &pcfg_pull_up_drv_8ma>;
};
emmc_clk: emmc-clk {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <2 RK_PB6 1 &pcfg_pull_none_drv_8ma>;
};
emmc_cmd: emmc-cmd {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <2 RK_PB4 2 &pcfg_pull_up_drv_8ma>;
};
};
gmac {
rmii_pins: rmii-pins {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PC5 2 &pcfg_pull_none>,
<1 RK_PC3 2 &pcfg_pull_none>,
<1 RK_PC4 2 &pcfg_pull_none>,
<1 RK_PB2 3 &pcfg_pull_none_drv_12ma>,
<1 RK_PB3 3 &pcfg_pull_none_drv_12ma>,
<1 RK_PB4 3 &pcfg_pull_none_drv_12ma>,
<1 RK_PB5 3 &pcfg_pull_none>,
<1 RK_PB6 3 &pcfg_pull_none>,
<1 RK_PB7 3 &pcfg_pull_none>,
<1 RK_PC2 3 &pcfg_pull_none>;
};
};
i2c0 {
i2c0_xfer: i2c0-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PB1 1 &pcfg_pull_none_smt>,
<0 RK_PB2 1 &pcfg_pull_none_smt>;
};
};
i2c1 {
i2c1_xfer: i2c1-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <2 RK_PD3 1 &pcfg_pull_up>,
<2 RK_PD4 1 &pcfg_pull_up>;
};
};
i2c2m1 {
i2c2m1_xfer: i2c2m1-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PC2 2 &pcfg_pull_none>,
<0 RK_PC6 3 &pcfg_pull_none>;
};
i2c2m1_gpio: i2c2m1-gpio {
rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>,
<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
i2c2m05v {
i2c2m05v_xfer: i2c2m05v-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD5 2 &pcfg_pull_none>,
<1 RK_PD4 2 &pcfg_pull_none>;
};
i2c2m05v_gpio: i2c2m05v-gpio {
rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>,
<1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
i2c3 {
i2c3_xfer: i2c3-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PB6 1 &pcfg_pull_none>,
<0 RK_PC4 2 &pcfg_pull_none>;
};
};
pwm0 {
pwm0_pin: pwm0-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PC5 1 &pcfg_pull_none>;
};
};
pwm1 {
pwm1_pin: pwm1-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PC4 1 &pcfg_pull_none>;
};
};
pwm2 {
pwm2_pin: pwm2-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PC6 1 &pcfg_pull_none>;
};
};
pwm3 {
pwm3_pin: pwm3-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PC0 1 &pcfg_pull_none>;
};
};
pwm4 {
pwm4_pin: pwm4-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PC1 3 &pcfg_pull_none>;
};
};
pwm5 {
pwm5_pin: pwm5-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PA7 2 &pcfg_pull_none>;
};
};
pwm6 {
pwm6_pin: pwm6-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PB0 2 &pcfg_pull_none>;
};
};
pwm7 {
pwm7_pin: pwm7-pin {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PB1 2 &pcfg_pull_none>;
};
};
sdmmc {
sdmmc_clk: sdmmc-clk {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PC4 1 &pcfg_pull_none_drv_4ma>;
};
sdmmc_cmd: sdmmc-cmd {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PC5 1 &pcfg_pull_up_drv_4ma>;
};
sdmmc_cd: sdmmc-cd {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PA1 1 &pcfg_pull_up_drv_4ma>;
};
sdmmc_bus1: sdmmc-bus1 {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PC3 1 &pcfg_pull_up_drv_4ma>;
};
sdmmc_bus4: sdmmc-bus4 {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PC3 1 &pcfg_pull_up_drv_4ma>,
<3 RK_PC2 1 &pcfg_pull_up_drv_4ma>,
<3 RK_PC1 1 &pcfg_pull_up_drv_4ma>,
<3 RK_PC0 1 &pcfg_pull_up_drv_4ma>;
};
};
spim0 {
spim0_clk: spim0-clk {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD0 2 &pcfg_pull_up>;
};
spim0_cs0: spim0-cs0 {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD1 2 &pcfg_pull_up>;
};
spim0_tx: spim0-tx {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD3 2 &pcfg_pull_up>;
};
spim0_rx: spim0-rx {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD2 2 &pcfg_pull_up>;
};
};
spim1 {
spim1_clk: spim1-clk {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PA3 1 &pcfg_pull_up>;
};
spim1_cs0: spim1-cs0 {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PA4 1 &pcfg_pull_up>;
};
spim1_rx: spim1-rx {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PB0 1 &pcfg_pull_up>;
};
spim1_tx: spim1-tx {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PA7 1 &pcfg_pull_up>;
};
};
tsadc {
otp_out: otp-out {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <0 RK_PB7 1 &pcfg_pull_none>;
};
otp_gpio: otp-gpio {
rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
uart0 {
uart0_xfer: uart0-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PA6 1 &pcfg_pull_up>,
<3 RK_PA5 1 &pcfg_pull_none>;
};
uart0_cts: uart0-cts {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PA4 1 &pcfg_pull_none>;
};
uart0_rts: uart0-rts {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PA3 1 &pcfg_pull_none>;
};
uart0_rts_gpio: uart0-rts-gpio {
rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
uart1 {
uart1_xfer: uart1-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD3 1 &pcfg_pull_up>,
<1 RK_PD2 1 &pcfg_pull_none>;
};
uart1_cts: uart1-cts {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>;
};
uart1_rts: uart1-rts {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD1 1 &pcfg_pull_none>;
};
};
uart2m0 {
uart2m0_xfer: uart2m0-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <2 RK_PD2 1 &pcfg_pull_up>,
<2 RK_PD1 1 &pcfg_pull_none>;
};
};
uart2m1 {
uart2m1_xfer: uart2m1-xfer {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <3 RK_PC3 2 &pcfg_pull_up>,
<3 RK_PC2 2 &pcfg_pull_none>;
};
};
uart2_5v {
uart2_5v_cts: uart2_5v-cts {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>;
};
uart2_5v_rts: uart2_5v-rts {
ARM: dts: rockchip: bulk convert gpios to their constant counterparts Rockchip SoCs use 2 different numbering schemes. Where the gpio- controllers just count 0-31 for their 32 gpios, the underlying iomux controller splits these into 4 separate entities A-D. Device-schematics always use these iomux-values to identify pins, so to make mapping schematics to devicetree easier Andy Yan introduced named constants for the pins but so far we only used them on new additions. Using a sed-script created by Emil Renner Berthing bulk-convert the remaining raw gpio numbers into their descriptive counterparts and also gets rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x mappings: /rockchip,pins *=/bcheck b # to end of script :append-next-line N :check /^[^;]*$/bappend-next-line s/<RK_GPIO\([0-9]\) /<\1 /g s/<\([^ ][^ ]* *\)0 /<\1RK_PA0 /g s/<\([^ ][^ ]* *\)1 /<\1RK_PA1 /g s/<\([^ ][^ ]* *\)2 /<\1RK_PA2 /g s/<\([^ ][^ ]* *\)3 /<\1RK_PA3 /g s/<\([^ ][^ ]* *\)4 /<\1RK_PA4 /g s/<\([^ ][^ ]* *\)5 /<\1RK_PA5 /g s/<\([^ ][^ ]* *\)6 /<\1RK_PA6 /g s/<\([^ ][^ ]* *\)7 /<\1RK_PA7 /g s/<\([^ ][^ ]* *\)8 /<\1RK_PB0 /g s/<\([^ ][^ ]* *\)9 /<\1RK_PB1 /g s/<\([^ ][^ ]* *\)10 /<\1RK_PB2 /g s/<\([^ ][^ ]* *\)11 /<\1RK_PB3 /g s/<\([^ ][^ ]* *\)12 /<\1RK_PB4 /g s/<\([^ ][^ ]* *\)13 /<\1RK_PB5 /g s/<\([^ ][^ ]* *\)14 /<\1RK_PB6 /g s/<\([^ ][^ ]* *\)15 /<\1RK_PB7 /g s/<\([^ ][^ ]* *\)16 /<\1RK_PC0 /g s/<\([^ ][^ ]* *\)17 /<\1RK_PC1 /g s/<\([^ ][^ ]* *\)18 /<\1RK_PC2 /g s/<\([^ ][^ ]* *\)19 /<\1RK_PC3 /g s/<\([^ ][^ ]* *\)20 /<\1RK_PC4 /g s/<\([^ ][^ ]* *\)21 /<\1RK_PC5 /g s/<\([^ ][^ ]* *\)22 /<\1RK_PC6 /g s/<\([^ ][^ ]* *\)23 /<\1RK_PC7 /g s/<\([^ ][^ ]* *\)24 /<\1RK_PD0 /g s/<\([^ ][^ ]* *\)25 /<\1RK_PD1 /g s/<\([^ ][^ ]* *\)26 /<\1RK_PD2 /g s/<\([^ ][^ ]* *\)27 /<\1RK_PD3 /g s/<\([^ ][^ ]* *\)28 /<\1RK_PD4 /g s/<\([^ ][^ ]* *\)29 /<\1RK_PD5 /g s/<\([^ ][^ ]* *\)30 /<\1RK_PD6 /g s/<\([^ ][^ ]* *\)31 /<\1RK_PD7 /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)0 /<\1RK_FUNC_GPIO /g s/<\([^ ][^ ]* *[^ ][^ ]* *\)RK_FUNC_\([1-9]\) /<\1\2 /g Suggested-by: Emil Renner Berthing <esmil@mailme.dk> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-04-02 19:08:57 +07:00
rockchip,pins = <1 RK_PD5 1 &pcfg_pull_none>;
};
};
};
};