linux_dsm_epyc7002/arch/powerpc/platforms/powernv/smp.c

325 lines
8.2 KiB
C
Raw Normal View History

/*
* SMP support for PowerNV machines.
*
* Copyright 2011 IBM Corp.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/sched.h>
#include <linux/sched/hotplug.h>
#include <linux/smp.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/cpu.h>
#include <asm/irq.h>
#include <asm/smp.h>
#include <asm/paca.h>
#include <asm/machdep.h>
#include <asm/cputable.h>
#include <asm/firmware.h>
#include <asm/vdso_datapage.h>
#include <asm/cputhreads.h>
#include <asm/xics.h>
#include <asm/xive.h>
#include <asm/opal.h>
#include <asm/runlatch.h>
#include <asm/code-patching.h>
#include <asm/dbell.h>
#include <asm/kvm_ppc.h>
#include <asm/ppc-opcode.h>
#include <asm/cpuidle.h>
#include "powernv.h"
#ifdef DEBUG
#include <asm/udbg.h>
#define DBG(fmt...) udbg_printf(fmt)
#else
#define DBG(fmt...)
#endif
static void pnv_smp_setup_cpu(int cpu)
{
if (xive_enabled())
xive_smp_setup_cpu();
else if (cpu != boot_cpuid)
xics_setup_cpu();
}
static int pnv_smp_kick_cpu(int nr)
{
unsigned int pcpu = get_hard_smp_processor_id(nr);
unsigned long start_here =
__pa(ppc_function_entry(generic_secondary_smp_init));
long rc;
uint8_t status;
BUG_ON(nr < 0 || nr >= NR_CPUS);
/*
* If we already started or OPAL is not supported, we just
* kick the CPU via the PACA
*/
if (paca[nr].cpu_start || !firmware_has_feature(FW_FEATURE_OPAL))
goto kick;
/*
* At this point, the CPU can either be spinning on the way in
* from kexec or be inside OPAL waiting to be started for the
* first time. OPAL v3 allows us to query OPAL to know if it
* has the CPUs, so we do that
*/
rc = opal_query_cpu_status(pcpu, &status);
if (rc != OPAL_SUCCESS) {
pr_warn("OPAL Error %ld querying CPU %d state\n", rc, nr);
return -ENODEV;
}
/*
* Already started, just kick it, probably coming from
* kexec and spinning
*/
if (status == OPAL_THREAD_STARTED)
goto kick;
/*
* Available/inactive, let's kick it
*/
if (status == OPAL_THREAD_INACTIVE) {
pr_devel("OPAL: Starting CPU %d (HW 0x%x)...\n", nr, pcpu);
rc = opal_start_cpu(pcpu, start_here);
if (rc != OPAL_SUCCESS) {
pr_warn("OPAL Error %ld starting CPU %d\n", rc, nr);
return -ENODEV;
}
} else {
/*
* An unavailable CPU (or any other unknown status)
* shouldn't be started. It should also
* not be in the possible map but currently it can
* happen
*/
pr_devel("OPAL: CPU %d (HW 0x%x) is unavailable"
" (status %d)...\n", nr, pcpu, status);
return -ENODEV;
}
kick:
return smp_generic_kick_cpu(nr);
}
#ifdef CONFIG_HOTPLUG_CPU
static int pnv_smp_cpu_disable(void)
{
int cpu = smp_processor_id();
/* This is identical to pSeries... might consolidate by
* moving migrate_irqs_away to a ppc_md with default to
* the generic fixup_irqs. --BenH.
*/
set_cpu_online(cpu, false);
vdso_data->processorCount--;
if (cpu == boot_cpuid)
boot_cpuid = cpumask_any(cpu_online_mask);
if (xive_enabled())
xive_smp_disable_cpu();
else
xics_migrate_irqs_away();
return 0;
}
static void pnv_smp_cpu_kill_self(void)
{
unsigned int cpu;
unsigned long srr1, wmask;
/* Standard hot unplug procedure */
local_irq_disable();
idle_task_exit();
current->active_mm = NULL; /* for sanity */
cpu = smp_processor_id();
DBG("CPU%d offline\n", cpu);
generic_set_cpu_dead(cpu);
smp_wmb();
wmask = SRR1_WAKEMASK;
if (cpu_has_feature(CPU_FTR_ARCH_207S))
wmask = SRR1_WAKEMASK_P8;
/* We don't want to take decrementer interrupts while we are offline,
* so clear LPCR:PECE1. We keep PECE2 (and LPCR_PECE_HVEE on P9)
* enabled as to let IPIs in.
*/
mtspr(SPRN_LPCR, mfspr(SPRN_LPCR) & ~(u64)LPCR_PECE1);
powerpc/powernv: Handle irq_happened flag correctly in off-line loop This fixes a bug where it is possible for an off-line CPU to fail to go into a low-power state (nap/sleep/winkle), and to become unresponsive to requests from the KVM subsystem to wake up and run a VCPU. What can happen is that a maskable interrupt of some kind (external, decrementer, hypervisor doorbell, or HMI) after we have called local_irq_disable() at the beginning of pnv_smp_cpu_kill_self() and before interrupts are hard-disabled inside power7_nap/sleep/winkle(). In this situation, the pending event is marked in the irq_happened flag in the PACA. This pending event prevents power7_nap/sleep/winkle from going to the requested low-power state; instead they return immediately. We don't deal with any of these pending event flags in the off-line loop in pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case, so we will have srr1 == 0, and none of the processing to clear interrupts or doorbells will be done. Usually, the most obvious symptom of this is that a KVM guest will fail with a console message saying "KVM: couldn't grab cpu N". This fixes the problem by making sure we handle the irq_happened flags properly. First, we hard-disable before the off-line loop. Once we have hard-disabled, the irq_happened flags can't change underneath us. We unconditionally clear the DEC and HMI flags: there is no processing of timer interrupts while off-line, and the necessary HMI processing is all done in lower-level code. We leave the EE and DBELL flags alone for the first iteration of the loop, so that we won't fail to respond to a split-core request that came in just before hard-disabling. Within the loop, we handle external interrupts if the EE bit is set in irq_happened as well as if the low-power state was interrupted by an external interrupt. (We don't need to do the msgclr for a pending doorbell in irq_happened, because doorbells are edge-triggered and don't remain pending in hardware.) Then we clear both the EE and DBELL flags, and once clear, they cannot be set again (until this CPU comes online again, that is). This also fixes the debug check to not be done when we just ran a KVM guest or when the sleep didn't happen because of a pending event in irq_happened. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-10-21 12:06:24 +07:00
/*
* Hard-disable interrupts, and then clear irq_happened flags
* that we can safely ignore while off-line, since they
* are for things for which we do no processing when off-line
* (or in the case of HMI, all the processing we need to do
* is done in lower-level real-mode code).
*/
hard_irq_disable();
local_paca->irq_happened &= ~(PACA_IRQ_DEC | PACA_IRQ_HMI);
while (!generic_check_cpu_restart(cpu)) {
powerpc/powernv: Handle irq_happened flag correctly in off-line loop This fixes a bug where it is possible for an off-line CPU to fail to go into a low-power state (nap/sleep/winkle), and to become unresponsive to requests from the KVM subsystem to wake up and run a VCPU. What can happen is that a maskable interrupt of some kind (external, decrementer, hypervisor doorbell, or HMI) after we have called local_irq_disable() at the beginning of pnv_smp_cpu_kill_self() and before interrupts are hard-disabled inside power7_nap/sleep/winkle(). In this situation, the pending event is marked in the irq_happened flag in the PACA. This pending event prevents power7_nap/sleep/winkle from going to the requested low-power state; instead they return immediately. We don't deal with any of these pending event flags in the off-line loop in pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case, so we will have srr1 == 0, and none of the processing to clear interrupts or doorbells will be done. Usually, the most obvious symptom of this is that a KVM guest will fail with a console message saying "KVM: couldn't grab cpu N". This fixes the problem by making sure we handle the irq_happened flags properly. First, we hard-disable before the off-line loop. Once we have hard-disabled, the irq_happened flags can't change underneath us. We unconditionally clear the DEC and HMI flags: there is no processing of timer interrupts while off-line, and the necessary HMI processing is all done in lower-level code. We leave the EE and DBELL flags alone for the first iteration of the loop, so that we won't fail to respond to a split-core request that came in just before hard-disabling. Within the loop, we handle external interrupts if the EE bit is set in irq_happened as well as if the low-power state was interrupted by an external interrupt. (We don't need to do the msgclr for a pending doorbell in irq_happened, because doorbells are edge-triggered and don't remain pending in hardware.) Then we clear both the EE and DBELL flags, and once clear, they cannot be set again (until this CPU comes online again, that is). This also fixes the debug check to not be done when we just ran a KVM guest or when the sleep didn't happen because of a pending event in irq_happened. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-10-21 12:06:24 +07:00
/*
* Clear IPI flag, since we don't handle IPIs while
* offline, except for those when changing micro-threading
* mode, which are handled explicitly below, and those
* for coming online, which are handled via
* generic_check_cpu_restart() calls.
*/
kvmppc_set_host_ipi(cpu, 0);
ppc64_runlatch_off();
srr1 = pnv_cpu_offline(cpu);
ppc64_runlatch_on();
powerpc/powernv: Add support for POWER8 split core on powernv Upcoming POWER8 chips support a concept called split core. This is where the core can be split into subcores that although not full cores, are able to appear as full cores to a guest. The splitting & unsplitting procedure is mildly complicated, and explained at length in the comments within the patch. One notable detail is that when splitting or unsplitting we need to pull offline cpus out of their offline state to do work as part of the procedure. The interface for changing the split mode is via a sysfs file, eg: $ echo 2 > /sys/devices/system/cpu/subcores_per_core Currently supported values are '1', '2' and '4'. And indicate respectively that the core should be unsplit, split in half, and split in quarters. These modes correspond to threads_per_subcore of 8, 4 and 2. We do not allow changing the split mode while KVM VMs are active. This is to prevent the value changing while userspace is configuring the VM, and also to prevent the mode being changed in such a way that existing guests are unable to be run. CPU hotplug fixes by Srivatsa. max_cpus fixes by Mahesh. cpuset fixes by benh. Fix for irq race by paulus. The rest by mikey and mpe. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2014-05-23 15:15:30 +07:00
powerpc/powernv: Return to cpu offline loop when finished in KVM guest When a secondary hardware thread has finished running a KVM guest, we currently put that thread into nap mode using a nap instruction in the KVM code. This changes the code so that instead of doing a nap instruction directly, we instead cause the call to power7_nap() that put the thread into nap mode to return. The reason for doing this is to avoid having the KVM code having to know what low-power mode to put the thread into. In the case of a secondary thread used to run a KVM guest, the thread will be offline from the point of view of the host kernel, and the relevant power7_nap() call is the one in pnv_smp_cpu_disable(). In this case we don't want to clear pending IPIs in the offline loop in that function, since that might cause us to miss the wakeup for the next time the thread needs to run a guest. To tell whether or not to clear the interrupt, we use the SRR1 value returned from power7_nap(), and check if it indicates an external interrupt. We arrange that the return from power7_nap() when we have finished running a guest returns 0, so pending interrupts don't get flushed in that case. Note that it is important a secondary thread that has finished executing in the guest, or that didn't have a guest to run, should not return to power7_nap's caller while the kvm_hstate.hwthread_req flag in the PACA is non-zero, because the return from power7_nap will reenable the MMU, and the MMU might still be in guest context. In this situation we spin at low priority in real mode waiting for hwthread_req to become zero. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2014-12-03 10:48:40 +07:00
/*
* If the SRR1 value indicates that we woke up due to
* an external interrupt, then clear the interrupt.
* We clear the interrupt before checking for the
* reason, so as to avoid a race where we wake up for
* some other reason, find nothing and clear the interrupt
* just as some other cpu is sending us an interrupt.
* If we returned from power7_nap as a result of
* having finished executing in a KVM guest, then srr1
* contains 0.
*/
powerpc/powernv: Handle irq_happened flag correctly in off-line loop This fixes a bug where it is possible for an off-line CPU to fail to go into a low-power state (nap/sleep/winkle), and to become unresponsive to requests from the KVM subsystem to wake up and run a VCPU. What can happen is that a maskable interrupt of some kind (external, decrementer, hypervisor doorbell, or HMI) after we have called local_irq_disable() at the beginning of pnv_smp_cpu_kill_self() and before interrupts are hard-disabled inside power7_nap/sleep/winkle(). In this situation, the pending event is marked in the irq_happened flag in the PACA. This pending event prevents power7_nap/sleep/winkle from going to the requested low-power state; instead they return immediately. We don't deal with any of these pending event flags in the off-line loop in pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case, so we will have srr1 == 0, and none of the processing to clear interrupts or doorbells will be done. Usually, the most obvious symptom of this is that a KVM guest will fail with a console message saying "KVM: couldn't grab cpu N". This fixes the problem by making sure we handle the irq_happened flags properly. First, we hard-disable before the off-line loop. Once we have hard-disabled, the irq_happened flags can't change underneath us. We unconditionally clear the DEC and HMI flags: there is no processing of timer interrupts while off-line, and the necessary HMI processing is all done in lower-level code. We leave the EE and DBELL flags alone for the first iteration of the loop, so that we won't fail to respond to a split-core request that came in just before hard-disabling. Within the loop, we handle external interrupts if the EE bit is set in irq_happened as well as if the low-power state was interrupted by an external interrupt. (We don't need to do the msgclr for a pending doorbell in irq_happened, because doorbells are edge-triggered and don't remain pending in hardware.) Then we clear both the EE and DBELL flags, and once clear, they cannot be set again (until this CPU comes online again, that is). This also fixes the debug check to not be done when we just ran a KVM guest or when the sleep didn't happen because of a pending event in irq_happened. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-10-21 12:06:24 +07:00
if (((srr1 & wmask) == SRR1_WAKEEE) ||
((srr1 & wmask) == SRR1_WAKEHVI) ||
powerpc/powernv: Handle irq_happened flag correctly in off-line loop This fixes a bug where it is possible for an off-line CPU to fail to go into a low-power state (nap/sleep/winkle), and to become unresponsive to requests from the KVM subsystem to wake up and run a VCPU. What can happen is that a maskable interrupt of some kind (external, decrementer, hypervisor doorbell, or HMI) after we have called local_irq_disable() at the beginning of pnv_smp_cpu_kill_self() and before interrupts are hard-disabled inside power7_nap/sleep/winkle(). In this situation, the pending event is marked in the irq_happened flag in the PACA. This pending event prevents power7_nap/sleep/winkle from going to the requested low-power state; instead they return immediately. We don't deal with any of these pending event flags in the off-line loop in pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case, so we will have srr1 == 0, and none of the processing to clear interrupts or doorbells will be done. Usually, the most obvious symptom of this is that a KVM guest will fail with a console message saying "KVM: couldn't grab cpu N". This fixes the problem by making sure we handle the irq_happened flags properly. First, we hard-disable before the off-line loop. Once we have hard-disabled, the irq_happened flags can't change underneath us. We unconditionally clear the DEC and HMI flags: there is no processing of timer interrupts while off-line, and the necessary HMI processing is all done in lower-level code. We leave the EE and DBELL flags alone for the first iteration of the loop, so that we won't fail to respond to a split-core request that came in just before hard-disabling. Within the loop, we handle external interrupts if the EE bit is set in irq_happened as well as if the low-power state was interrupted by an external interrupt. (We don't need to do the msgclr for a pending doorbell in irq_happened, because doorbells are edge-triggered and don't remain pending in hardware.) Then we clear both the EE and DBELL flags, and once clear, they cannot be set again (until this CPU comes online again, that is). This also fixes the debug check to not be done when we just ran a KVM guest or when the sleep didn't happen because of a pending event in irq_happened. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-10-21 12:06:24 +07:00
(local_paca->irq_happened & PACA_IRQ_EE)) {
if (cpu_has_feature(CPU_FTR_ARCH_300)) {
if (xive_enabled())
xive_flush_interrupt();
else
icp_opal_flush_interrupt();
} else
icp_native_flush_interrupt();
} else if ((srr1 & wmask) == SRR1_WAKEHDBELL) {
unsigned long msg = PPC_DBELL_TYPE(PPC_DBELL_SERVER);
asm volatile(PPC_MSGCLR(%0) : : "r" (msg));
powerpc/powernv: Return to cpu offline loop when finished in KVM guest When a secondary hardware thread has finished running a KVM guest, we currently put that thread into nap mode using a nap instruction in the KVM code. This changes the code so that instead of doing a nap instruction directly, we instead cause the call to power7_nap() that put the thread into nap mode to return. The reason for doing this is to avoid having the KVM code having to know what low-power mode to put the thread into. In the case of a secondary thread used to run a KVM guest, the thread will be offline from the point of view of the host kernel, and the relevant power7_nap() call is the one in pnv_smp_cpu_disable(). In this case we don't want to clear pending IPIs in the offline loop in that function, since that might cause us to miss the wakeup for the next time the thread needs to run a guest. To tell whether or not to clear the interrupt, we use the SRR1 value returned from power7_nap(), and check if it indicates an external interrupt. We arrange that the return from power7_nap() when we have finished running a guest returns 0, so pending interrupts don't get flushed in that case. Note that it is important a secondary thread that has finished executing in the guest, or that didn't have a guest to run, should not return to power7_nap's caller while the kvm_hstate.hwthread_req flag in the PACA is non-zero, because the return from power7_nap will reenable the MMU, and the MMU might still be in guest context. In this situation we spin at low priority in real mode waiting for hwthread_req to become zero. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2014-12-03 10:48:40 +07:00
}
powerpc/powernv: Handle irq_happened flag correctly in off-line loop This fixes a bug where it is possible for an off-line CPU to fail to go into a low-power state (nap/sleep/winkle), and to become unresponsive to requests from the KVM subsystem to wake up and run a VCPU. What can happen is that a maskable interrupt of some kind (external, decrementer, hypervisor doorbell, or HMI) after we have called local_irq_disable() at the beginning of pnv_smp_cpu_kill_self() and before interrupts are hard-disabled inside power7_nap/sleep/winkle(). In this situation, the pending event is marked in the irq_happened flag in the PACA. This pending event prevents power7_nap/sleep/winkle from going to the requested low-power state; instead they return immediately. We don't deal with any of these pending event flags in the off-line loop in pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case, so we will have srr1 == 0, and none of the processing to clear interrupts or doorbells will be done. Usually, the most obvious symptom of this is that a KVM guest will fail with a console message saying "KVM: couldn't grab cpu N". This fixes the problem by making sure we handle the irq_happened flags properly. First, we hard-disable before the off-line loop. Once we have hard-disabled, the irq_happened flags can't change underneath us. We unconditionally clear the DEC and HMI flags: there is no processing of timer interrupts while off-line, and the necessary HMI processing is all done in lower-level code. We leave the EE and DBELL flags alone for the first iteration of the loop, so that we won't fail to respond to a split-core request that came in just before hard-disabling. Within the loop, we handle external interrupts if the EE bit is set in irq_happened as well as if the low-power state was interrupted by an external interrupt. (We don't need to do the msgclr for a pending doorbell in irq_happened, because doorbells are edge-triggered and don't remain pending in hardware.) Then we clear both the EE and DBELL flags, and once clear, they cannot be set again (until this CPU comes online again, that is). This also fixes the debug check to not be done when we just ran a KVM guest or when the sleep didn't happen because of a pending event in irq_happened. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-10-21 12:06:24 +07:00
local_paca->irq_happened &= ~(PACA_IRQ_EE | PACA_IRQ_DBELL);
smp_mb();
powerpc/powernv: Add support for POWER8 split core on powernv Upcoming POWER8 chips support a concept called split core. This is where the core can be split into subcores that although not full cores, are able to appear as full cores to a guest. The splitting & unsplitting procedure is mildly complicated, and explained at length in the comments within the patch. One notable detail is that when splitting or unsplitting we need to pull offline cpus out of their offline state to do work as part of the procedure. The interface for changing the split mode is via a sysfs file, eg: $ echo 2 > /sys/devices/system/cpu/subcores_per_core Currently supported values are '1', '2' and '4'. And indicate respectively that the core should be unsplit, split in half, and split in quarters. These modes correspond to threads_per_subcore of 8, 4 and 2. We do not allow changing the split mode while KVM VMs are active. This is to prevent the value changing while userspace is configuring the VM, and also to prevent the mode being changed in such a way that existing guests are unable to be run. CPU hotplug fixes by Srivatsa. max_cpus fixes by Mahesh. cpuset fixes by benh. Fix for irq race by paulus. The rest by mikey and mpe. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2014-05-23 15:15:30 +07:00
if (cpu_core_split_required())
continue;
powerpc/powernv: Handle irq_happened flag correctly in off-line loop This fixes a bug where it is possible for an off-line CPU to fail to go into a low-power state (nap/sleep/winkle), and to become unresponsive to requests from the KVM subsystem to wake up and run a VCPU. What can happen is that a maskable interrupt of some kind (external, decrementer, hypervisor doorbell, or HMI) after we have called local_irq_disable() at the beginning of pnv_smp_cpu_kill_self() and before interrupts are hard-disabled inside power7_nap/sleep/winkle(). In this situation, the pending event is marked in the irq_happened flag in the PACA. This pending event prevents power7_nap/sleep/winkle from going to the requested low-power state; instead they return immediately. We don't deal with any of these pending event flags in the off-line loop in pnv_smp_cpu_kill_self() because power7_nap et al. return 0 in this case, so we will have srr1 == 0, and none of the processing to clear interrupts or doorbells will be done. Usually, the most obvious symptom of this is that a KVM guest will fail with a console message saying "KVM: couldn't grab cpu N". This fixes the problem by making sure we handle the irq_happened flags properly. First, we hard-disable before the off-line loop. Once we have hard-disabled, the irq_happened flags can't change underneath us. We unconditionally clear the DEC and HMI flags: there is no processing of timer interrupts while off-line, and the necessary HMI processing is all done in lower-level code. We leave the EE and DBELL flags alone for the first iteration of the loop, so that we won't fail to respond to a split-core request that came in just before hard-disabling. Within the loop, we handle external interrupts if the EE bit is set in irq_happened as well as if the low-power state was interrupted by an external interrupt. (We don't need to do the msgclr for a pending doorbell in irq_happened, because doorbells are edge-triggered and don't remain pending in hardware.) Then we clear both the EE and DBELL flags, and once clear, they cannot be set again (until this CPU comes online again, that is). This also fixes the debug check to not be done when we just ran a KVM guest or when the sleep didn't happen because of a pending event in irq_happened. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-10-21 12:06:24 +07:00
if (srr1 && !generic_check_cpu_restart(cpu))
DBG("CPU%d Unexpected exit while offline !\n", cpu);
}
/* Re-enable decrementer interrupts */
mtspr(SPRN_LPCR, mfspr(SPRN_LPCR) | LPCR_PECE1);
DBG("CPU%d coming online...\n", cpu);
}
#endif /* CONFIG_HOTPLUG_CPU */
static int pnv_cpu_bootable(unsigned int nr)
{
/*
* Starting with POWER8, the subcore logic relies on all threads of a
* core being booted so that they can participate in split mode
* switches. So on those machines we ignore the smt_enabled_at_boot
* setting (smt-enabled on the kernel command line).
*/
if (cpu_has_feature(CPU_FTR_ARCH_207S))
return 1;
return smp_generic_cpu_bootable(nr);
}
static int pnv_smp_prepare_cpu(int cpu)
{
if (xive_enabled())
return xive_smp_prepare_cpu(cpu);
return 0;
}
/* Cause IPI as setup by the interrupt controller (xics or xive) */
static void (*ic_cause_ipi)(int cpu);
static void pnv_cause_ipi(int cpu)
{
if (doorbell_try_core_ipi(cpu))
return;
ic_cause_ipi(cpu);
}
static void pnv_p9_dd1_cause_ipi(int cpu)
{
int this_cpu = get_cpu();
/*
* POWER9 DD1 has a global addressed msgsnd, but for now we restrict
* IPIs to same core, because it requires additional synchronization
* for inter-core doorbells which we do not implement.
*/
if (cpumask_test_cpu(cpu, cpu_sibling_mask(this_cpu)))
doorbell_global_ipi(cpu);
else
ic_cause_ipi(cpu);
put_cpu();
}
static void __init pnv_smp_probe(void)
{
if (xive_enabled())
xive_smp_probe();
else
xics_smp_probe();
if (cpu_has_feature(CPU_FTR_DBELL)) {
ic_cause_ipi = smp_ops->cause_ipi;
WARN_ON(!ic_cause_ipi);
if (cpu_has_feature(CPU_FTR_ARCH_300)) {
if (cpu_has_feature(CPU_FTR_POWER9_DD1))
smp_ops->cause_ipi = pnv_p9_dd1_cause_ipi;
else
smp_ops->cause_ipi = doorbell_global_ipi;
} else {
smp_ops->cause_ipi = pnv_cause_ipi;
}
}
}
static struct smp_ops_t pnv_smp_ops = {
.message_pass = NULL, /* Use smp_muxed_ipi_message_pass */
.cause_ipi = NULL, /* Filled at runtime by pnv_smp_probe() */
.probe = pnv_smp_probe,
.prepare_cpu = pnv_smp_prepare_cpu,
.kick_cpu = pnv_smp_kick_cpu,
.setup_cpu = pnv_smp_setup_cpu,
.cpu_bootable = pnv_cpu_bootable,
#ifdef CONFIG_HOTPLUG_CPU
.cpu_disable = pnv_smp_cpu_disable,
.cpu_die = generic_cpu_die,
#endif /* CONFIG_HOTPLUG_CPU */
};
/* This is called very early during platform setup_arch */
void __init pnv_smp_init(void)
{
smp_ops = &pnv_smp_ops;
#ifdef CONFIG_HOTPLUG_CPU
ppc_md.cpu_die = pnv_smp_cpu_kill_self;
#endif
}