linux_dsm_epyc7002/drivers/usb/chipidea/host.c

286 lines
6.6 KiB
C
Raw Normal View History

/*
* host.c - ChipIdea USB host controller driver
*
* Copyright (c) 2012 Intel Corporation
*
* Author: Alexander Shishkin
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/kernel.h>
#include <linux/io.h>
#include <linux/usb.h>
#include <linux/usb/hcd.h>
#include <linux/usb/chipidea.h>
#include <linux/regulator/consumer.h>
#include "../host/ehci.h"
#include "ci.h"
#include "bits.h"
#include "host.h"
static struct hc_driver __read_mostly ci_ehci_hc_driver;
usb: chipidea: host: add .bus_suspend quirk For chipidea, its resume sequence is not-EHCI compatible, see below description for FPR at portsc. So in order to send SoF in time for remote wakeup sequence(within 3ms), the RUN/STOP bit must be set before the resume signal is ended, but the usb resume code may run after resume signal is ended, so we had to set it at suspend path. Force Port Resume - RW. Default = 0b. 1= Resume detected/driven on port. 0=No resume (K-state) detected/driven on port. Host mode: Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if a J-to-K transition is detected while the port is in the Suspend state. When this bit transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in the USBSTS register is also set to '1'. This bit will automatically change to '0' after the resume sequence is complete. This behavior is different from EHCI where the controller driver is required to set this bit to a '0' after the resume duration is timed in the driver. Note that when the controller owns the port, the resume sequence follows the defined sequence documented in the USB Specification Revision 2.0. The resume signaling (Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain a '1' until the port has switched to idle. Writing a '0' has no affect because the port controller will time the resume operation, clear the bit and the port control state switches to HS or FS idle. This field is '0' if Port Power(PP) is '0' in host mode. This bit is not-EHCI compatible. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-11 11:44:59 +07:00
static int (*orig_bus_suspend)(struct usb_hcd *hcd);
struct ehci_ci_priv {
struct regulator *reg_vbus;
};
static int ehci_ci_portpower(struct usb_hcd *hcd, int portnum, bool enable)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct ehci_ci_priv *priv = (struct ehci_ci_priv *)ehci->priv;
struct device *dev = hcd->self.controller;
struct ci_hdrc *ci = dev_get_drvdata(dev);
int ret = 0;
int port = HCS_N_PORTS(ehci->hcs_params);
if (priv->reg_vbus) {
if (port > 1) {
dev_warn(dev,
"Not support multi-port regulator control\n");
return 0;
}
if (enable)
ret = regulator_enable(priv->reg_vbus);
else
ret = regulator_disable(priv->reg_vbus);
if (ret) {
dev_err(dev,
"Failed to %s vbus regulator, ret=%d\n",
enable ? "enable" : "disable", ret);
return ret;
}
}
if (enable && (ci->platdata->phy_mode == USBPHY_INTERFACE_MODE_HSIC)) {
/*
* Marvell 28nm HSIC PHY requires forcing the port to HS mode.
* As HSIC is always HS, this should be safe for others.
*/
hw_port_test_set(ci, 5);
hw_port_test_set(ci, 0);
}
return 0;
};
static int ehci_ci_reset(struct usb_hcd *hcd)
{
struct device *dev = hcd->self.controller;
struct ci_hdrc *ci = dev_get_drvdata(dev);
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
int ret;
ret = ehci_setup(hcd);
if (ret)
return ret;
ehci->need_io_watchdog = 0;
if (ci->platdata->notify_event) {
ret = ci->platdata->notify_event(ci,
CI_HDRC_CONTROLLER_RESET_EVENT);
if (ret)
return ret;
}
ci_platform_configure(ci);
return ret;
}
static const struct ehci_driver_overrides ehci_ci_overrides = {
.extra_priv_size = sizeof(struct ehci_ci_priv),
.port_power = ehci_ci_portpower,
.reset = ehci_ci_reset,
};
static irqreturn_t host_irq(struct ci_hdrc *ci)
{
return usb_hcd_irq(ci->irq, ci->hcd);
}
static int host_start(struct ci_hdrc *ci)
{
struct usb_hcd *hcd;
struct ehci_hcd *ehci;
struct ehci_ci_priv *priv;
int ret;
if (usb_disabled())
return -ENODEV;
hcd = usb_create_hcd(&ci_ehci_hc_driver, ci->dev, dev_name(ci->dev));
if (!hcd)
return -ENOMEM;
dev_set_drvdata(ci->dev, ci);
hcd->rsrc_start = ci->hw_bank.phys;
hcd->rsrc_len = ci->hw_bank.size;
hcd->regs = ci->hw_bank.abs;
hcd->has_tt = 1;
hcd->power_budget = ci->platdata->power_budget;
hcd->tpl_support = ci->platdata->tpl_support;
if (ci->phy)
hcd->phy = ci->phy;
else
hcd->usb_phy = ci->usb_phy;
ehci = hcd_to_ehci(hcd);
ehci->caps = ci->hw_bank.cap;
ehci->has_hostpc = ci->hw_bank.lpm;
ehci->has_tdi_phy_lpm = ci->hw_bank.lpm;
ehci->imx28_write_fix = ci->imx28_write_fix;
priv = (struct ehci_ci_priv *)ehci->priv;
priv->reg_vbus = NULL;
if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci)) {
if (ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON) {
ret = regulator_enable(ci->platdata->reg_vbus);
if (ret) {
dev_err(ci->dev,
"Failed to enable vbus regulator, ret=%d\n",
ret);
goto put_hcd;
}
} else {
priv->reg_vbus = ci->platdata->reg_vbus;
}
}
ret = usb_add_hcd(hcd, 0, 0);
if (ret) {
goto disable_reg;
} else {
struct usb_otg *otg = &ci->otg;
ci->hcd = hcd;
if (ci_otg_is_fsm_mode(ci)) {
otg->host = &hcd->self;
hcd->self.otg_port = 1;
}
}
return ret;
disable_reg:
if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) &&
(ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON))
regulator_disable(ci->platdata->reg_vbus);
put_hcd:
usb_put_hcd(hcd);
return ret;
}
static void host_stop(struct ci_hdrc *ci)
{
struct usb_hcd *hcd = ci->hcd;
usb/chipidea: fix oops on memory allocation failure When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses the kernel while trying to remove and put the HCD which doesn't exist: WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511 __dma_alloc+0x200/0x240() coherent pool not initialised! Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func Backtrace: [<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c) r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00 [<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c) [<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c) r4:df883a60 r3:df86ad00 [<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40) r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80 [<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240) r3:00000000 r2:c05fda00 [<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0) [<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438) [<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664) [<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180) [<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670 ) r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904 [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) ... ---[ end trace c88ccaf3969e8422 ]--- Unable to handle kernel NULL pointer dereference at virtual address 00000028 pgd = c0004000 [00000028] *pgd=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func task: df86ad00 ti: df882000 task.ti: df882000 PC is at usb_remove_hcd+0x10/0x150 LR is at host_stop+0x1c/0x3c pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013 sp : df883b50 ip : df883b78 fp : df883b74 r10: c11f4c54 r9 : c0836450 r8 : df30c400 r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010 r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 2f29404a DAC: 00000015 Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240) Stack: (0xdf883b50 to 0xdf884000) ... Backtrace: [<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c) r6:df2ef410 r5:00000000 r4:df2c3010 [<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20) r5:00000000 r4:df2c3010 [<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670) [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) [<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48) ... ---[ end trace c88ccaf3969e8423 ]--- Fix this so at least we can continue booting and get to a shell prompt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-16 19:45:15 +07:00
if (hcd) {
if (ci->platdata->notify_event)
ci->platdata->notify_event(ci,
CI_HDRC_CONTROLLER_STOPPED_EVENT);
usb/chipidea: fix oops on memory allocation failure When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses the kernel while trying to remove and put the HCD which doesn't exist: WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511 __dma_alloc+0x200/0x240() coherent pool not initialised! Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func Backtrace: [<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c) r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00 [<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c) [<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c) r4:df883a60 r3:df86ad00 [<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40) r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80 [<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240) r3:00000000 r2:c05fda00 [<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0) [<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438) [<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664) [<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180) [<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670 ) r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904 [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) ... ---[ end trace c88ccaf3969e8422 ]--- Unable to handle kernel NULL pointer dereference at virtual address 00000028 pgd = c0004000 [00000028] *pgd=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func task: df86ad00 ti: df882000 task.ti: df882000 PC is at usb_remove_hcd+0x10/0x150 LR is at host_stop+0x1c/0x3c pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013 sp : df883b50 ip : df883b78 fp : df883b74 r10: c11f4c54 r9 : c0836450 r8 : df30c400 r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010 r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 2f29404a DAC: 00000015 Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240) Stack: (0xdf883b50 to 0xdf884000) ... Backtrace: [<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c) r6:df2ef410 r5:00000000 r4:df2c3010 [<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20) r5:00000000 r4:df2c3010 [<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670) [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) [<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48) ... ---[ end trace c88ccaf3969e8423 ]--- Fix this so at least we can continue booting and get to a shell prompt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-16 19:45:15 +07:00
usb_remove_hcd(hcd);
ci->role = CI_ROLE_END;
synchronize_irq(ci->irq);
usb/chipidea: fix oops on memory allocation failure When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses the kernel while trying to remove and put the HCD which doesn't exist: WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511 __dma_alloc+0x200/0x240() coherent pool not initialised! Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func Backtrace: [<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c) r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00 [<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c) [<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c) r4:df883a60 r3:df86ad00 [<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40) r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80 [<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240) r3:00000000 r2:c05fda00 [<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0) [<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438) [<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664) [<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180) [<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670 ) r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904 [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) ... ---[ end trace c88ccaf3969e8422 ]--- Unable to handle kernel NULL pointer dereference at virtual address 00000028 pgd = c0004000 [00000028] *pgd=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func task: df86ad00 ti: df882000 task.ti: df882000 PC is at usb_remove_hcd+0x10/0x150 LR is at host_stop+0x1c/0x3c pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013 sp : df883b50 ip : df883b78 fp : df883b74 r10: c11f4c54 r9 : c0836450 r8 : df30c400 r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010 r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 2f29404a DAC: 00000015 Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240) Stack: (0xdf883b50 to 0xdf884000) ... Backtrace: [<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c) r6:df2ef410 r5:00000000 r4:df2c3010 [<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20) r5:00000000 r4:df2c3010 [<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670) [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) [<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48) ... ---[ end trace c88ccaf3969e8423 ]--- Fix this so at least we can continue booting and get to a shell prompt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-16 19:45:15 +07:00
usb_put_hcd(hcd);
if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) &&
(ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON))
regulator_disable(ci->platdata->reg_vbus);
usb/chipidea: fix oops on memory allocation failure When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses the kernel while trying to remove and put the HCD which doesn't exist: WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511 __dma_alloc+0x200/0x240() coherent pool not initialised! Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func Backtrace: [<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c) r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00 [<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c) [<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c) r4:df883a60 r3:df86ad00 [<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40) r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80 [<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240) r3:00000000 r2:c05fda00 [<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0) [<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438) [<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664) [<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180) [<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670 ) r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904 [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) ... ---[ end trace c88ccaf3969e8422 ]--- Unable to handle kernel NULL pointer dereference at virtual address 00000028 pgd = c0004000 [00000028] *pgd=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56 Workqueue: deferwq deferred_probe_work_func task: df86ad00 ti: df882000 task.ti: df882000 PC is at usb_remove_hcd+0x10/0x150 LR is at host_stop+0x1c/0x3c pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013 sp : df883b50 ip : df883b78 fp : df883b74 r10: c11f4c54 r9 : c0836450 r8 : df30c400 r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010 r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 2f29404a DAC: 00000015 Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240) Stack: (0xdf883b50 to 0xdf884000) ... Backtrace: [<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c) r6:df2ef410 r5:00000000 r4:df2c3010 [<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20) r5:00000000 r4:df2c3010 [<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670) [<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24) [<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234) [<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48) ... ---[ end trace c88ccaf3969e8423 ]--- Fix this so at least we can continue booting and get to a shell prompt. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-10-16 19:45:15 +07:00
}
ci->hcd = NULL;
ci->otg.host = NULL;
}
void ci_hdrc_host_destroy(struct ci_hdrc *ci)
{
if (ci->role == CI_ROLE_HOST && ci->hcd)
host_stop(ci);
}
usb: chipidea: host: add .bus_suspend quirk For chipidea, its resume sequence is not-EHCI compatible, see below description for FPR at portsc. So in order to send SoF in time for remote wakeup sequence(within 3ms), the RUN/STOP bit must be set before the resume signal is ended, but the usb resume code may run after resume signal is ended, so we had to set it at suspend path. Force Port Resume - RW. Default = 0b. 1= Resume detected/driven on port. 0=No resume (K-state) detected/driven on port. Host mode: Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if a J-to-K transition is detected while the port is in the Suspend state. When this bit transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in the USBSTS register is also set to '1'. This bit will automatically change to '0' after the resume sequence is complete. This behavior is different from EHCI where the controller driver is required to set this bit to a '0' after the resume duration is timed in the driver. Note that when the controller owns the port, the resume sequence follows the defined sequence documented in the USB Specification Revision 2.0. The resume signaling (Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain a '1' until the port has switched to idle. Writing a '0' has no affect because the port controller will time the resume operation, clear the bit and the port control state switches to HS or FS idle. This field is '0' if Port Power(PP) is '0' in host mode. This bit is not-EHCI compatible. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-11 11:44:59 +07:00
static int ci_ehci_bus_suspend(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
int port;
u32 tmp;
int ret = orig_bus_suspend(hcd);
if (ret)
return ret;
port = HCS_N_PORTS(ehci->hcs_params);
while (port--) {
u32 __iomem *reg = &ehci->regs->port_status[port];
u32 portsc = ehci_readl(ehci, reg);
if (portsc & PORT_CONNECT) {
/*
* For chipidea, the resume signal will be ended
* automatically, so for remote wakeup case, the
* usbcmd.rs may not be set before the resume has
* ended if other resume paths consumes too much
* time (~24ms), in that case, the SOF will not
* send out within 3ms after resume ends, then the
* high speed device will enter full speed mode.
*/
tmp = ehci_readl(ehci, &ehci->regs->command);
tmp |= CMD_RUN;
ehci_writel(ehci, tmp, &ehci->regs->command);
/*
* It needs a short delay between set RS bit and PHCD.
*/
usleep_range(150, 200);
break;
}
}
return 0;
}
int ci_hdrc_host_init(struct ci_hdrc *ci)
{
struct ci_role_driver *rdrv;
if (!hw_read(ci, CAP_DCCPARAMS, DCCPARAMS_HC))
return -ENXIO;
rdrv = devm_kzalloc(ci->dev, sizeof(struct ci_role_driver), GFP_KERNEL);
if (!rdrv)
return -ENOMEM;
rdrv->start = host_start;
rdrv->stop = host_stop;
rdrv->irq = host_irq;
rdrv->name = "host";
ci->roles[CI_ROLE_HOST] = rdrv;
usb: chipidea: ehci_init_driver is intended to call one time The ehci_init_driver is used to initialize hcd APIs for each ehci controller driver, it is designed to be called only one time and before driver register is called. The current design will cause ehci_init_driver is called multiple times at probe process, it will cause hc_driver's initialization affect current running hcd. We run out NULL pointer dereference problem when one hcd is started by module_init, and the other is started by otg thread at SMP platform. The reason for this problem is ehci_init_driver will do memory copy for current uniform hc_driver, and this memory copy will do memset (as 0) first, so when the first hcd is running usb_add_hcd, and the second hcd may clear the uniform hc_driver's space (at ehci_init_driver), then the first hcd will meet NULL pointer at the same time. See below two logs: LOG_1: ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.1: doesn't support gadget Unable to handle kernel NULL pointer dereference at virtual address 00000014 pgd = 80004000 [00000014] *pgd=00000000 Internal error: Oops: 805 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 108 Comm: kworker/u8:2 Not tainted 3.14.38-222193-g24b2734-dirty #25 Workqueue: ci_otg ci_otg_work task: d839ec00 ti: d8400000 task.ti: d8400000 PC is at ehci_run+0x4c/0x284 LR is at _raw_spin_unlock_irqrestore+0x28/0x54 pc : [<8041f9a0>] lr : [<8070ea84>] psr: 60000113 sp : d8401e30 ip : 00000000 fp : d8004400 r10: 00000001 r9 : 00000001 r8 : 00000000 r7 : 00000000 r6 : d8419940 r5 : 80dd24c0 r4 : d8419800 r3 : 8001d060 r2 : 00000000 r1 : 00000001 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 1000404a DAC: 00000015 Process kworker/u8:2 (pid: 108, stack limit = 0xd8400238) Stack: (0xd8401e30 to 0xd8402000) 1e20: d87523c0 d8401e48 66667562 d8419800 1e40: 00000000 00000000 d8419800 00000000 00000000 00000000 d84198b0 8040fcdc 1e60: 00000000 80dd320c d8477610 d8419c00 d803d010 d8419800 00000000 00000000 1e80: d8004400 00000000 d8400008 80431494 80431374 d803d100 d803d010 d803d1ac 1ea0: 00000000 80432428 804323d4 d803d100 00000001 80435eb8 80e0d0bc d803d100 1ec0: 00000006 80436458 00000000 d803d100 80e92ec8 80436f44 d803d010 d803d100 1ee0: d83fde00 8043292c d8752710 d803d1f4 d803d010 8042ddfc 8042ddb8 d83f3b00 1f00: d803d1f4 80042b60 00000000 00000003 00000001 00000001 80054598 d83f3b00 1f20: d8004400 d83f3b18 d8004414 d8400000 80e3957b 00000089 d8004400 80043814 1f40: d839ec00 00000000 d83fcd80 d83f3b00 800436e4 00000000 00000000 00000000 1f60: 00000000 80048f34 00000000 00000000 00000000 d83f3b00 00000000 00000000 1f80: d8401f80 d8401f80 00000000 00000000 d8401f90 d8401f90 d8401fac d83fcd80 1fa0: 80048e68 00000000 00000000 8000e538 00000000 00000000 00000000 00000000 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [<8041f9a0>] (ehci_run) from [<8040fcdc>] (usb_add_hcd+0x248/0x6e8) [<8040fcdc>] (usb_add_hcd) from [<80431494>] (host_start+0x120/0x2e4) [<80431494>] (host_start) from [<80432428>] (ci_otg_start_host+0x54/0xbc) [<80432428>] (ci_otg_start_host) from [<80435eb8>] (otg_set_protocol+0xa4/0xd0) [<80435eb8>] (otg_set_protocol) from [<80436458>] (otg_set_state+0x574/0xc58) [<80436458>] (otg_set_state) from [<80436f44>] (otg_statemachine+0x408/0x46c) [<80436f44>] (otg_statemachine) from [<8043292c>] (ci_otg_fsm_work+0x3c/0x190) [<8043292c>] (ci_otg_fsm_work) from [<8042ddfc>] (ci_otg_work+0x44/0x1c4) [<8042ddfc>] (ci_otg_work) from [<80042b60>] (process_one_work+0xf4/0x35c) [<80042b60>] (process_one_work) from [<80043814>] (worker_thread+0x130/0x3bc) [<80043814>] (worker_thread) from [<80048f34>] (kthread+0xcc/0xe4) [<80048f34>] (kthread) from [<8000e538>] (ret_from_fork+0x14/0x3c) Code: e5953018 e3530000 0a000000 e12fff33 (e5878014) LOG_2: ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.1: doesn't support gadget Unable to handle kernel NULL pointer dereference at virtual address 00000000 pgd = 80004000 [00000000] *pgd=00000000 In Online 00:00ternal e Offline rror: Oops: 80000005 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 108 Comm: kworker/u8:2 Not tainted 3.14.38-02007-g24b2734-dirty #127 Workque Online 00:00ue: ci_o Offline tg ci_otg_work Online 00:00task: d8 Offline 39ec00 ti: d83ea000 task.ti: d83ea000 PC is at 0x0 LR is at usb_add_hcd+0x248/0x6e8 pc : [<00000000>] lr : [<8040f644>] psr: 60000113 sp : d83ebe60 ip : 00000000 fp : d8004400 r10: 00000001 r9 : 00000001 r8 : d85fd4b0 r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : d85fd400 r3 : 00000000 r2 : d85fd4f4 r1 : 80410178 r0 : d85fd400 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c53c7d Table: 1000404a DAC: 00000015 Process kworker/u8:2 (pid: 108, stack limit = 0xd83ea238) Stack: (0xd83ebe60 to 0xd83ec000) be60: 00000000 80dd920c d8654e10 d85fd800 d803e010 d85fd400 00000000 00000000 be80: d8004400 00000000 d83ea008 80430e34 80430d14 d803e100 d803e010 d803e1ac bea0: 00000000 80431dc8 80431d74 d803e100 00000001 80435858 80e130bc d803e100 bec0: 00000006 80435df8 00000000 d803e100 80e98ec8 804368e4 d803e010 d803e100 bee0: d86e8100 804322cc d86cf050 d803e1f4 d803e010 8042d79c 8042d758 d83cf900 bf00: d803e1f4 80042b78 00000000 00000003 00000001 00000001 800545e8 d83cf900 bf20: d8004400 d83cf918 d8004414 d83ea000 80e3f57b 00000089 d8004400 8004382c bf40: d839ec00 00000000 d8393780 d83cf900 800436fc 00000000 00000000 00000000 bf60: 00000000 80048f50 80e019f4 00000000 0000264c d83cf900 00000000 00000000 bf80: d83ebf80 d83ebf80 00000000 00000000 d83ebf90 d83ebf90 d83ebfac d8393780 bfa0: 80048e84 00000000 00000000 8000e538 00000000 00000000 00000000 00000000 bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ee66e85d 133ebd03 [<804 Online 00:000f644>] Offline (usb_add_hcd) from [<80430e34>] (host_start+0x120/0x2e4) [<80430e34>] (host_start) from [<80431dc8>] (ci_otg_start_host+0x54/0xbc) [<80431dc8>] (ci_otg_start_host) from [<80435858>] (otg_set_protocol+0xa4/0xd0) [<80435858>] (otg_set_protocol) from [<80435df8>] (otg_set_state+0x574/0xc58) [<80435df8>] (otg_set_state) from [<804368e4>] (otg_statemachine+0x408/0x46c) [<804368e4>] (otg_statemachine) from [<804322cc>] (ci_otg_fsm_work+0x3c/0x190) [<804322cc>] (ci_otg_fsm_work) from [<8042d79c>] (ci_otg_work+0x44/0x1c4) [<8042d79c>] (ci_otg_work) from [<80042b78>] (process_one_work+0xf4/0x35c) [<80042b78>] (process_one_work) from [<8004382c>] (worker_thread+0x130/0x3bc) [<8004382c>] (worker_thread) from [<80048f50>] (kthread+0xcc/0xe4) [<80048f50>] (kthread) from [<8000e538>] (ret_from_fork+0x14/0x3c) Code: bad PC value Cc: Jun Li <jun.li@freescale.com> Cc: <stable@vger.kernel.org> Cc: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peter Chen <peter.chen@freescale.com>
2015-07-21 08:51:29 +07:00
return 0;
}
void ci_hdrc_host_driver_init(void)
{
ehci_init_driver(&ci_ehci_hc_driver, &ehci_ci_overrides);
usb: chipidea: host: add .bus_suspend quirk For chipidea, its resume sequence is not-EHCI compatible, see below description for FPR at portsc. So in order to send SoF in time for remote wakeup sequence(within 3ms), the RUN/STOP bit must be set before the resume signal is ended, but the usb resume code may run after resume signal is ended, so we had to set it at suspend path. Force Port Resume - RW. Default = 0b. 1= Resume detected/driven on port. 0=No resume (K-state) detected/driven on port. Host mode: Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if a J-to-K transition is detected while the port is in the Suspend state. When this bit transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in the USBSTS register is also set to '1'. This bit will automatically change to '0' after the resume sequence is complete. This behavior is different from EHCI where the controller driver is required to set this bit to a '0' after the resume duration is timed in the driver. Note that when the controller owns the port, the resume sequence follows the defined sequence documented in the USB Specification Revision 2.0. The resume signaling (Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain a '1' until the port has switched to idle. Writing a '0' has no affect because the port controller will time the resume operation, clear the bit and the port control state switches to HS or FS idle. This field is '0' if Port Power(PP) is '0' in host mode. This bit is not-EHCI compatible. Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-02-11 11:44:59 +07:00
orig_bus_suspend = ci_ehci_hc_driver.bus_suspend;
ci_ehci_hc_driver.bus_suspend = ci_ehci_bus_suspend;
}