linux_dsm_epyc7002/include/linux/libata.h

1969 lines
64 KiB
C
Raw Normal View History

/*
* Copyright 2003-2005 Red Hat, Inc. All rights reserved.
* Copyright 2003-2005 Jeff Garzik
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/driver-api/libata.rst
*
*/
#ifndef __LINUX_LIBATA_H__
#define __LINUX_LIBATA_H__
#include <linux/delay.h>
#include <linux/jiffies.h>
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
#include <linux/scatterlist.h>
#include <linux/io.h>
#include <linux/ata.h>
#include <linux/workqueue.h>
2006-04-12 00:12:34 +07:00
#include <scsi/scsi_host.h>
#include <linux/acpi.h>
#include <linux/cdrom.h>
libata: implement cross-port EH exclusion In libata, the non-EH code paths should always take and release ap->lock explicitly when accessing hardware or shared data structures. However, once EH is active, it's assumed that the port is owned by EH and EH methods don't explicitly take ap->lock unless race from irq handler or other code paths are expected. However, libata EH didn't guarantee exclusion among EHs for ports of the same host. IOW, multiple EHs may execute in parallel on multiple ports of the same controller. In many cases, especially in SATA, the ports are completely independent of each other and this doesn't cause problems; however, there are cases where different ports share the same resource, which lead to obscure timing related bugs such as the one fixed by commit 213373cf (ata_piix: fix locking around SIDPR access). This patch implements exclusion among EHs of the same host. When EH begins, it acquires per-host EH ownership by calling ata_eh_acquire(). When EH finishes, the ownership is released by calling ata_eh_release(). EH ownership is also released whenever the EH thread goes to sleep from ata_msleep() or explicitly and reacquired after waking up. This ensures that while EH is actively accessing the hardware, it has exclusive access to it while allowing EHs to interleave and progress in parallel as they hit waiting stages, which dominate the time spent in EH. This achieves cross-port EH exclusion without pervasive and fragile changes while still allowing parallel EH for the most part. This was first reported by yuanding02@gmail.com more than three years ago in the following bugzilla. :-) https://bugzilla.kernel.org/show_bug.cgi?id=8223 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Reported-by: yuanding02@gmail.com Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-06 22:57:14 +07:00
#include <linux/sched.h>
/*
* Define if arch has non-standard setup. This is a _PCI_ standard
* not a legacy or ISA standard.
*/
#ifdef CONFIG_ATA_NONSTANDARD
#include <asm/libata-portmap.h>
#else
#define ATA_PRIMARY_IRQ(dev) 14
#define ATA_SECONDARY_IRQ(dev) 15
#endif
/*
* compile-time options: to be removed as soon as all the drivers are
* converted to the new debugging mechanism
*/
#undef ATA_DEBUG /* debugging output */
#undef ATA_VERBOSE_DEBUG /* yet more debugging output */
#undef ATA_IRQ_TRAP /* define to ack screaming irqs */
#undef ATA_NDEBUG /* define to disable quick runtime checks */
/* note: prints function name for you */
#ifdef ATA_DEBUG
#define DPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#ifdef ATA_VERBOSE_DEBUG
#define VPRINTK(fmt, args...) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#else
#define VPRINTK(fmt, args...)
#endif /* ATA_VERBOSE_DEBUG */
#else
#define DPRINTK(fmt, args...)
#define VPRINTK(fmt, args...)
#endif /* ATA_DEBUG */
#define BPRINTK(fmt, args...) if (ap->flags & ATA_FLAG_DEBUGMSG) printk(KERN_ERR "%s: " fmt, __func__, ## args)
#define ata_print_version_once(dev, version) \
({ \
static bool __print_once; \
\
if (!__print_once) { \
__print_once = true; \
ata_print_version(dev, version); \
} \
})
/* NEW: debug levels */
#define HAVE_LIBATA_MSG 1
enum {
ATA_MSG_DRV = 0x0001,
ATA_MSG_INFO = 0x0002,
ATA_MSG_PROBE = 0x0004,
ATA_MSG_WARN = 0x0008,
ATA_MSG_MALLOC = 0x0010,
ATA_MSG_CTL = 0x0020,
ATA_MSG_INTR = 0x0040,
ATA_MSG_ERR = 0x0080,
};
#define ata_msg_drv(p) ((p)->msg_enable & ATA_MSG_DRV)
#define ata_msg_info(p) ((p)->msg_enable & ATA_MSG_INFO)
#define ata_msg_probe(p) ((p)->msg_enable & ATA_MSG_PROBE)
#define ata_msg_warn(p) ((p)->msg_enable & ATA_MSG_WARN)
#define ata_msg_malloc(p) ((p)->msg_enable & ATA_MSG_MALLOC)
#define ata_msg_ctl(p) ((p)->msg_enable & ATA_MSG_CTL)
#define ata_msg_intr(p) ((p)->msg_enable & ATA_MSG_INTR)
#define ata_msg_err(p) ((p)->msg_enable & ATA_MSG_ERR)
static inline u32 ata_msg_init(int dval, int default_msg_enable_bits)
{
if (dval < 0 || dval >= (sizeof(u32) * 8))
return default_msg_enable_bits; /* should be 0x1 - only driver info msgs */
if (!dval)
return 0;
return (1 << dval) - 1;
}
/* defines only for the constants which don't work well as enums */
#define ATA_TAG_POISON 0xfafbfcfdU
enum {
/* various global constants */
LIBATA_MAX_PRD = ATA_MAX_PRD / 2,
LIBATA_DUMB_MAX_PRD = ATA_MAX_PRD / 4, /* Worst case */
ATA_DEF_QUEUE = 1,
/* tag ATA_MAX_QUEUE - 1 is reserved for internal commands */
ATA_MAX_QUEUE = 32,
ATA_TAG_INTERNAL = ATA_MAX_QUEUE - 1,
ATA_SHORT_PAUSE = 16,
ATAPI_MAX_DRAIN = 16 << 10,
ATA_ALL_DEVICES = (1 << ATA_MAX_DEVICES) - 1,
ATA_SHT_EMULATED = 1,
ATA_SHT_THIS_ID = -1,
2005-10-22 11:19:33 +07:00
ATA_SHT_USE_CLUSTERING = 1,
/* struct ata_taskfile flags */
ATA_TFLAG_LBA48 = (1 << 0), /* enable 48-bit LBA and "HOB" */
ATA_TFLAG_ISADDR = (1 << 1), /* enable r/w to nsect/lba regs */
ATA_TFLAG_DEVICE = (1 << 2), /* enable r/w to device reg */
ATA_TFLAG_WRITE = (1 << 3), /* data dir: host->dev==1 (write) */
ATA_TFLAG_LBA = (1 << 4), /* enable LBA */
ATA_TFLAG_FUA = (1 << 5), /* enable FUA */
ATA_TFLAG_POLLING = (1 << 6), /* set nIEN to 1 and use polling */
/* struct ata_device stuff */
ATA_DFLAG_LBA = (1 << 0), /* device supports LBA */
ATA_DFLAG_LBA48 = (1 << 1), /* device supports LBA48 */
ATA_DFLAG_CDB_INTR = (1 << 2), /* device asserts INTRQ when ready for CDB */
ATA_DFLAG_NCQ = (1 << 3), /* device supports NCQ */
ATA_DFLAG_FLUSH_EXT = (1 << 4), /* do FLUSH_EXT instead of FLUSH */
ATA_DFLAG_ACPI_PENDING = (1 << 5), /* ACPI resume action pending */
ATA_DFLAG_ACPI_FAILED = (1 << 6), /* ACPI on devcfg has failed */
ATA_DFLAG_AN = (1 << 7), /* AN configured */
ATA_DFLAG_TRUSTED = (1 << 8), /* device supports trusted send/recv */
ATA_DFLAG_DMADIR = (1 << 10), /* device requires DMADIR */
ATA_DFLAG_CFG_MASK = (1 << 12) - 1,
ATA_DFLAG_PIO = (1 << 12), /* device limited to PIO mode */
ATA_DFLAG_NCQ_OFF = (1 << 13), /* device limited to non-NCQ mode */
ATA_DFLAG_SLEEPING = (1 << 15), /* device is sleeping */
ATA_DFLAG_DUBIOUS_XFER = (1 << 16), /* data transfer not verified */
ATA_DFLAG_NO_UNLOAD = (1 << 17), /* device doesn't support unload */
ATA_DFLAG_UNLOCK_HPA = (1 << 18), /* unlock HPA */
ATA_DFLAG_NCQ_SEND_RECV = (1 << 19), /* device supports NCQ SEND and RECV */
ATA_DFLAG_NCQ_PRIO = (1 << 20), /* device supports NCQ priority */
ATA_DFLAG_NCQ_PRIO_ENABLE = (1 << 21), /* Priority cmds sent to dev */
ATA_DFLAG_INIT_MASK = (1 << 24) - 1,
ATA_DFLAG_DETACH = (1 << 24),
ATA_DFLAG_DETACHED = (1 << 25),
ATA_DFLAG_DA = (1 << 26), /* device supports Device Attention */
ATA_DFLAG_DEVSLP = (1 << 27), /* device supports Device Sleep */
ATA_DFLAG_ACPI_DISABLED = (1 << 28), /* ACPI for the device is disabled */
ATA_DFLAG_D_SENSE = (1 << 29), /* Descriptor sense requested */
ATA_DFLAG_ZAC = (1 << 30), /* ZAC device */
ATA_DEV_UNKNOWN = 0, /* unknown device */
ATA_DEV_ATA = 1, /* ATA device */
ATA_DEV_ATA_UNSUP = 2, /* ATA device (unsupported) */
ATA_DEV_ATAPI = 3, /* ATAPI device */
ATA_DEV_ATAPI_UNSUP = 4, /* ATAPI device (unsupported) */
ATA_DEV_PMP = 5, /* SATA port multiplier */
ATA_DEV_PMP_UNSUP = 6, /* SATA port multiplier (unsupported) */
ATA_DEV_SEMB = 7, /* SEMB */
ATA_DEV_SEMB_UNSUP = 8, /* SEMB (unsupported) */
ATA_DEV_ZAC = 9, /* ZAC device */
ATA_DEV_ZAC_UNSUP = 10, /* ZAC device (unsupported) */
ATA_DEV_NONE = 11, /* no device */
/* struct ata_link flags */
ATA_LFLAG_NO_HRST = (1 << 1), /* avoid hardreset */
ATA_LFLAG_NO_SRST = (1 << 2), /* avoid softreset */
ATA_LFLAG_ASSUME_ATA = (1 << 3), /* assume ATA class */
ATA_LFLAG_ASSUME_SEMB = (1 << 4), /* assume SEMB class */
ATA_LFLAG_ASSUME_CLASS = ATA_LFLAG_ASSUME_ATA | ATA_LFLAG_ASSUME_SEMB,
ATA_LFLAG_NO_RETRY = (1 << 5), /* don't retry this link */
ATA_LFLAG_DISABLED = (1 << 6), /* link is disabled */
ATA_LFLAG_SW_ACTIVITY = (1 << 7), /* keep activity stats */
libata: reimplement link power management The current LPM implementation has the following issues. * Operation order isn't well thought-out. e.g. HIPM should be configured after IPM in SControl is properly configured. Not the other way around. * Suspend/resume paths call ata_lpm_enable/disable() which must only be called from EH context directly. Also, ata_lpm_enable/disable() were called whether LPM was in use or not. * Implementation is per-port when it should be per-link. As a result, it can't be used for controllers with slave links or PMP. * LPM state isn't managed consistently. After a link reset for whatever reason including suspend/resume the actual LPM state would be reset leaving ap->lpm_policy inconsistent. * Generic/driver-specific logic boundary isn't clear. Currently, libahci has to mangle stuff which libata EH proper should be handling. This makes the implementation unnecessarily complex and fragile. * Tied to ALPM. Doesn't consider DIPM only cases and doesn't check whether the device allows HIPM. * Error handling isn't implemented. Given the extent of mismatch with the rest of libata, I don't think trying to fix it piecewise makes much sense. This patch reimplements LPM support. * The new implementation is per-link. The target policy is still port-wide (ap->target_lpm_policy) but all the mechanisms and states are per-link and integrate well with the rest of link abstraction and can work with slave and PMP links. * Core EH has proper control of LPM state. LPM state is reconfigured when and only when reconfiguration is necessary. It makes sure that LPM state is reset when probing for new device on the link. Controller agnostic logic is now implemented in libata EH proper and driver implementation only has to deal with controller specifics. * Proper error handling. LPM config failure is attributed to the device on the link and LPM is disabled for the link if it fails repeatedly. * ops->enable/disable_pm() are replaced with single ops->set_lpm() which takes @policy and @hints. This simplifies driver specific implementation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-01 22:50:06 +07:00
ATA_LFLAG_NO_LPM = (1 << 8), /* disable LPM on this link */
ATA_LFLAG_RST_ONCE = (1 << 9), /* limit recovery to one reset */
ATA_LFLAG_CHANGED = (1 << 10), /* LPM state changed on this link */
ATA_LFLAG_NO_DB_DELAY = (1 << 11), /* no debounce delay on link resume */
/* struct ata_port flags */
ATA_FLAG_SLAVE_POSS = (1 << 0), /* host supports slave dev */
/* (doesn't imply presence) */
ATA_FLAG_SATA = (1 << 1),
ATA_FLAG_NO_LOG_PAGE = (1 << 5), /* do not issue log page read */
ATA_FLAG_NO_ATAPI = (1 << 6), /* No ATAPI support */
ATA_FLAG_PIO_DMA = (1 << 7), /* PIO cmds via DMA */
ATA_FLAG_PIO_LBA48 = (1 << 8), /* Host DMA engine is LBA28 only */
ATA_FLAG_PIO_POLLING = (1 << 9), /* use polling PIO if LLD
* doesn't handle PIO interrupts */
ATA_FLAG_NCQ = (1 << 10), /* host supports NCQ */
ATA_FLAG_NO_POWEROFF_SPINDOWN = (1 << 11), /* don't spindown before poweroff */
ATA_FLAG_NO_HIBERNATE_SPINDOWN = (1 << 12), /* don't spindown before hibernation */
ATA_FLAG_DEBUGMSG = (1 << 13),
ATA_FLAG_FPDMA_AA = (1 << 14), /* driver supports Auto-Activate */
ATA_FLAG_IGN_SIMPLEX = (1 << 15), /* ignore SIMPLEX */
ATA_FLAG_NO_IORDY = (1 << 16), /* controller lacks iordy */
ATA_FLAG_ACPI_SATA = (1 << 17), /* need native SATA ACPI layout */
ATA_FLAG_AN = (1 << 18), /* controller supports AN */
ATA_FLAG_PMP = (1 << 19), /* controller supports PMP */
ATA_FLAG_FPDMA_AUX = (1 << 20), /* controller supports H2DFIS aux field */
ATA_FLAG_EM = (1 << 21), /* driver supports enclosure
* management */
ATA_FLAG_SW_ACTIVITY = (1 << 22), /* driver supports sw activity
* led */
ATA_FLAG_NO_DIPM = (1 << 23), /* host not happy with DIPM */
ATA_FLAG_SAS_HOST = (1 << 24), /* SAS host */
/* bits 24:31 of ap->flags are reserved for LLD specific flags */
/* struct ata_port pflags */
ATA_PFLAG_EH_PENDING = (1 << 0), /* EH pending */
ATA_PFLAG_EH_IN_PROGRESS = (1 << 1), /* EH in progress */
ATA_PFLAG_FROZEN = (1 << 2), /* port is frozen */
ATA_PFLAG_RECOVERED = (1 << 3), /* recovery action performed */
ATA_PFLAG_LOADING = (1 << 4), /* boot/loading probe */
ATA_PFLAG_SCSI_HOTPLUG = (1 << 6), /* SCSI hotplug scheduled */
ATA_PFLAG_INITIALIZING = (1 << 7), /* being initialized, don't touch */
ATA_PFLAG_RESETTING = (1 << 8), /* reset in progress */
ATA_PFLAG_UNLOADING = (1 << 9), /* driver is being unloaded */
ATA_PFLAG_UNLOADED = (1 << 10), /* driver is unloaded */
ATA_PFLAG_SUSPENDED = (1 << 17), /* port is suspended (power) */
ATA_PFLAG_PM_PENDING = (1 << 18), /* PM operation pending */
ATA_PFLAG_INIT_GTM_VALID = (1 << 19), /* initial gtm data valid */
ATA_PFLAG_PIO32 = (1 << 20), /* 32bit PIO */
ATA_PFLAG_PIO32CHANGE = (1 << 21), /* 32bit PIO can be turned on/off */
ATA_PFLAG_EXTERNAL = (1 << 22), /* eSATA/external port */
/* struct ata_queued_cmd flags */
ATA_QCFLAG_ACTIVE = (1 << 0), /* cmd not yet ack'd to scsi lyer */
ATA_QCFLAG_DMAMAP = (1 << 1), /* SG table is DMA mapped */
ATA_QCFLAG_IO = (1 << 3), /* standard IO command */
ATA_QCFLAG_RESULT_TF = (1 << 4), /* result TF requested */
ATA_QCFLAG_CLEAR_EXCL = (1 << 5), /* clear excl_link on completion */
ATA_QCFLAG_QUIET = (1 << 6), /* don't report device error */
ATA_QCFLAG_RETRY = (1 << 7), /* retry after failure */
ATA_QCFLAG_FAILED = (1 << 16), /* cmd failed and is owned by EH */
ATA_QCFLAG_SENSE_VALID = (1 << 17), /* sense data valid */
ATA_QCFLAG_EH_SCHEDULED = (1 << 18), /* EH scheduled (obsolete) */
/* host set flags */
ATA_HOST_SIMPLEX = (1 << 0), /* Host is simplex, one DMA channel per host only */
ATA_HOST_STARTED = (1 << 1), /* Host started */
ATA_HOST_PARALLEL_SCAN = (1 << 2), /* Ports on this host can be scanned in parallel */
ATA_HOST_IGNORE_ATA = (1 << 3), /* Ignore ATA devices on this host. */
2006-08-31 11:02:15 +07:00
/* bits 24:31 of host->flags are reserved for LLD specific flags */
/* various lengths of time */
ATA_TMOUT_BOOT = 30000, /* heuristic */
ATA_TMOUT_BOOT_QUICK = 7000, /* heuristic */
ATA_TMOUT_INTERNAL_QUICK = 5000,
ATA_TMOUT_MAX_PARK = 30000,
/*
* GoVault needs 2s and iVDR disk HHD424020F7SV00 800ms. 2s
* is too much without parallel probing. Use 2s if parallel
* probing is available, 800ms otherwise.
*/
ATA_TMOUT_FF_WAIT_LONG = 2000,
ATA_TMOUT_FF_WAIT = 800,
libata: restructure SFF post-reset readiness waits Previously, post-softreset readiness is waited as follows. 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff. If not, continue to #3. 3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending on devmask using ata_sff_wait_ready(). And for post-hardreset readiness, 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. sata_sff_hardreset waits for device readiness using ata_sff_wait_ready(). This patch merges and unifies post-reset readiness waits into ata_sff_wait_ready() and ata_sff_wait_after_reset(). ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF status is 0xff, link status is unknown and the port is SATA, it will continue polling till ATA_TMOUT_FF_WAIT. ata_sff_wait_after_reset() is updated to perform the following steps. 1. waits for 150ms. 2. waits for dev0 readiness using ata_sff_wait_ready(). Note that this is done regardless of devmask, as ata_sff_wait_ready() handles 0xff status correctly, this preserves the original behavior except that it may wait longer after softreset if link is online but status is 0xff. This behavior change is very unlikely to cause any actual difference and is intended. It brings softreset behavior to that of hardreset. 3. waits for dev1 readiness just the same way ata_bus_post_reset() did. Now both soft and hard resets call ata_sff_wait_after_reset() after reset to wait for readiness after resets. As ata_sff_wait_after_reset() contains calls to ->sff_dev_select(), explicit call near the end of sata_sff_hardreset() is removed. This change makes reset implementation simpler and more consistent. While at it, make the magical 150ms wait post-reset wait duration a constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take @link instead of @ap. This is to make them consistent with other reset helpers and ease core changes. pata_scc is updated accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-07 20:47:19 +07:00
/* Spec mandates to wait for ">= 2ms" before checking status
* after reset. We wait 150ms, because that was the magic
* delay used for ATAPI devices in Hale Landis's ATADRVR, for
* the period of time between when the ATA command register is
* written, and then status is checked. Because waiting for
* "a while" before checking status is fine, post SRST, we
* perform this magic delay here as well.
*
* Old drivers/ide uses the 2mS rule and then waits for ready.
*/
ATA_WAIT_AFTER_RESET = 150,
libata: restructure SFF post-reset readiness waits Previously, post-softreset readiness is waited as follows. 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff. If not, continue to #3. 3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending on devmask using ata_sff_wait_ready(). And for post-hardreset readiness, 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. sata_sff_hardreset waits for device readiness using ata_sff_wait_ready(). This patch merges and unifies post-reset readiness waits into ata_sff_wait_ready() and ata_sff_wait_after_reset(). ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF status is 0xff, link status is unknown and the port is SATA, it will continue polling till ATA_TMOUT_FF_WAIT. ata_sff_wait_after_reset() is updated to perform the following steps. 1. waits for 150ms. 2. waits for dev0 readiness using ata_sff_wait_ready(). Note that this is done regardless of devmask, as ata_sff_wait_ready() handles 0xff status correctly, this preserves the original behavior except that it may wait longer after softreset if link is online but status is 0xff. This behavior change is very unlikely to cause any actual difference and is intended. It brings softreset behavior to that of hardreset. 3. waits for dev1 readiness just the same way ata_bus_post_reset() did. Now both soft and hard resets call ata_sff_wait_after_reset() after reset to wait for readiness after resets. As ata_sff_wait_after_reset() contains calls to ->sff_dev_select(), explicit call near the end of sata_sff_hardreset() is removed. This change makes reset implementation simpler and more consistent. While at it, make the magical 150ms wait post-reset wait duration a constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take @link instead of @ap. This is to make them consistent with other reset helpers and ease core changes. pata_scc is updated accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-07 20:47:19 +07:00
/* If PMP is supported, we have to do follow-up SRST. As some
* PMPs don't send D2H Reg FIS after hardreset, LLDs are
* advised to wait only for the following duration before
* doing SRST.
*/
ATA_TMOUT_PMP_SRST_WAIT = 5000,
/* When the LPM policy is set to ATA_LPM_MAX_POWER, there might
* be a spurious PHY event, so ignore the first PHY event that
* occurs within 10s after the policy change.
*/
ATA_TMOUT_SPURIOUS_PHY = 10000,
/* ATA bus states */
BUS_UNKNOWN = 0,
BUS_DMA = 1,
BUS_IDLE = 2,
BUS_NOINTR = 3,
BUS_NODATA = 4,
BUS_TIMER = 5,
BUS_PIO = 6,
BUS_EDD = 7,
BUS_IDENTIFY = 8,
BUS_PACKET = 9,
/* SATA port states */
PORT_UNKNOWN = 0,
PORT_ENABLED = 1,
PORT_DISABLED = 2,
/* encoding various smaller bitmaps into a single
* unsigned long bitmap
*/
ATA_NR_PIO_MODES = 7,
ATA_NR_MWDMA_MODES = 5,
ATA_NR_UDMA_MODES = 8,
ATA_SHIFT_PIO = 0,
ATA_SHIFT_MWDMA = ATA_SHIFT_PIO + ATA_NR_PIO_MODES,
ATA_SHIFT_UDMA = ATA_SHIFT_MWDMA + ATA_NR_MWDMA_MODES,
ATA_SHIFT_PRIO = 6,
ATA_PRIO_HIGH = 2,
/* size of buffer to pad xfers ending on unaligned boundaries */
ATA_DMA_PAD_SZ = 4,
/* ering size */
ATA_ERING_SIZE = 32,
/* return values for ->qc_defer */
ATA_DEFER_LINK = 1,
ATA_DEFER_PORT = 2,
/* desc_len for ata_eh_info and context */
ATA_EH_DESC_LEN = 80,
/* reset / recovery action types */
ATA_EH_REVALIDATE = (1 << 0),
libata: prefer hardreset When both soft and hard resets are available, libata preferred softreset till now. The logic behind it was to be softer to devices; however, this doesn't really help much. Rationales for the change: * BIOS may freeze lock certain things during boot and softreset can't unlock those. This by itself is okay but during operation PHY event or other error conditions can trigger hardreset and the device may end up with different configuration. For example, after a hardreset, previously unlockable HPA can be unlocked resulting in different device size and thus revalidation failure. Similar condition can occur during or after resume. * Certain ATAPI devices require hardreset to recover after certain error conditions. On PATA, this is done by issuing the DEVICE RESET command. On SATA, COMRESET has equivalent effect. The problem is that DEVICE RESET needs its own execution protocol. For SFF controllers with bare TF access, it can be easily implemented but more advanced controllers (e.g. ahci and sata_sil24) require specialized implementations. Simply using hardreset solves the problem nicely. * COMRESET initialization sequence is the norm in SATA land and many SATA devices don't work properly if only SRST is used. For example, some PMPs behave this way and libata works around by always issuing hardreset if the host supports PMP. Like the above example, libata has developed a number of mechanisms aiming to promote softreset to hardreset if softreset is not going to work. This approach is time consuming and error prone. Also, note that, dependingon how you read the specs, it could be argued that PMP fan-out ports require COMRESET to start operation. In fact, all the PMPs on the market except one don't work properly if COMRESET is not issued to fan-out ports after PMP reset. * COMRESET is an integral part of SATA connection and any working device should be able to handle COMRESET properly. After all, it's the way to signal hardreset during reboot. This is the most used and recommended (at least by the ahci spec) method of resetting devices. So, this patch makes libata prefer hardreset over softreset by making the following changes. * Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is now only used to tell prereset whether soft or hard reset will be issued. * Strip out now unneeded promote-to-hardreset logics from ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and other places. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-01-23 22:05:14 +07:00
ATA_EH_SOFTRESET = (1 << 1), /* meaningful only in ->prereset */
ATA_EH_HARDRESET = (1 << 2), /* meaningful only in ->prereset */
ATA_EH_RESET = ATA_EH_SOFTRESET | ATA_EH_HARDRESET,
ATA_EH_ENABLE_LINK = (1 << 3),
ATA_EH_PARK = (1 << 5), /* unload heads and stop I/O */
ATA_EH_PERDEV_MASK = ATA_EH_REVALIDATE | ATA_EH_PARK,
ATA_EH_ALL_ACTIONS = ATA_EH_REVALIDATE | ATA_EH_RESET |
libata: reimplement link power management The current LPM implementation has the following issues. * Operation order isn't well thought-out. e.g. HIPM should be configured after IPM in SControl is properly configured. Not the other way around. * Suspend/resume paths call ata_lpm_enable/disable() which must only be called from EH context directly. Also, ata_lpm_enable/disable() were called whether LPM was in use or not. * Implementation is per-port when it should be per-link. As a result, it can't be used for controllers with slave links or PMP. * LPM state isn't managed consistently. After a link reset for whatever reason including suspend/resume the actual LPM state would be reset leaving ap->lpm_policy inconsistent. * Generic/driver-specific logic boundary isn't clear. Currently, libahci has to mangle stuff which libata EH proper should be handling. This makes the implementation unnecessarily complex and fragile. * Tied to ALPM. Doesn't consider DIPM only cases and doesn't check whether the device allows HIPM. * Error handling isn't implemented. Given the extent of mismatch with the rest of libata, I don't think trying to fix it piecewise makes much sense. This patch reimplements LPM support. * The new implementation is per-link. The target policy is still port-wide (ap->target_lpm_policy) but all the mechanisms and states are per-link and integrate well with the rest of link abstraction and can work with slave and PMP links. * Core EH has proper control of LPM state. LPM state is reconfigured when and only when reconfiguration is necessary. It makes sure that LPM state is reset when probing for new device on the link. Controller agnostic logic is now implemented in libata EH proper and driver implementation only has to deal with controller specifics. * Proper error handling. LPM config failure is attributed to the device on the link and LPM is disabled for the link if it fails repeatedly. * ops->enable/disable_pm() are replaced with single ops->set_lpm() which takes @policy and @hints. This simplifies driver specific implementation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-01 22:50:06 +07:00
ATA_EH_ENABLE_LINK,
/* ata_eh_info->flags */
ATA_EHI_HOTPLUGGED = (1 << 0), /* could have been hotplugged */
ATA_EHI_NO_AUTOPSY = (1 << 2), /* no autopsy */
ATA_EHI_QUIET = (1 << 3), /* be quiet */
ATA_EHI_NO_RECOVERY = (1 << 4), /* no recovery */
ATA_EHI_DID_SOFTRESET = (1 << 16), /* already soft-reset this port */
ATA_EHI_DID_HARDRESET = (1 << 17), /* already soft-reset this port */
ATA_EHI_PRINTINFO = (1 << 18), /* print configuration info */
ATA_EHI_SETMODE = (1 << 19), /* configure transfer mode */
ATA_EHI_POST_SETMODE = (1 << 20), /* revalidating after setmode */
ATA_EHI_DID_RESET = ATA_EHI_DID_SOFTRESET | ATA_EHI_DID_HARDRESET,
/* mask of flags to transfer *to* the slave link */
ATA_EHI_TO_SLAVE_MASK = ATA_EHI_NO_AUTOPSY | ATA_EHI_QUIET,
/* max tries if error condition is still set after ->error_handler */
ATA_EH_MAX_TRIES = 5,
/* sometimes resuming a link requires several retries */
ATA_LINK_RESUME_TRIES = 5,
/* how hard are we gonna try to probe/recover devices */
ATA_PROBE_MAX_TRIES = 3,
ATA_EH_DEV_TRIES = 3,
ATA_EH_PMP_TRIES = 5,
ATA_EH_PMP_LINK_TRIES = 3,
SATA_PMP_RW_TIMEOUT = 3000, /* PMP read/write timeout */
[PATCH] libata-hp-prep: add prereset() method and implement ata_std_prereset() With hotplug, every reset might be a probing reset and thus something similar to probe_init() is needed. prereset() method is called before a series of resets to a port and is the counterpart of postreset(). prereset() can tell EH to use different type of reset or skip reset by modifying ehc->i.action. This patch also implements ata_std_prereset(). Most controllers should be able to use this function directly or with some wrapping. After hotplug, different controllers need different actions to resume the PHY and detect the newly attached device. Controllers can be categorized as follows. * Controllers which can wait for the first D2H FIS after hotplug. Note that if the waiting is implemented by polling TF status, there needs to be a way to set BSY on PHY status change. It can be implemented by hardware or with the help of the driver. * Controllers which can wait for the first D2H FIS after sending COMRESET. These controllers need to issue COMRESET to wait for the first FIS. Note that the received D2H FIS could be the first D2H FIS after POR (power-on-reset) or D2H FIS in response to the COMRESET. Some controllers use COMRESET as TF status synchronization point and clear TF automatically (sata_sil). * Controllers which cannot wait for the first D2H FIS reliably. Blindly issuing SRST to spinning-up device often results in command issue failure or timeout, causing extended delay. For these controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT (currently 8s) to give newly attached device time to spin up, then issues reset. Note that failing to getting ready in ATA_SPINUP_WAIT is not critical. libata will retry. So, the timeout needs to be long enough to spin up most devices. LLDDs can tell ata_std_prereset() which of above action is needed with ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags. These flags are PHY-specific property and will be moved to ata_link later. While at it, this patch unifies function typedef's such that they all have named arguments. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31 16:27:48 +07:00
/* This should match the actual table size of
* ata_eh_cmd_timeout_table in libata-eh.c.
*/
ATA_EH_CMD_TIMEOUT_TABLE_SIZE = 6,
/* Horkage types. May be set by libata or controller on drives
(some horkage may be drive/controller pair dependent */
ATA_HORKAGE_DIAGNOSTIC = (1 << 0), /* Failed boot diag */
ATA_HORKAGE_NODMA = (1 << 1), /* DMA problems */
ATA_HORKAGE_NONCQ = (1 << 2), /* Don't use NCQ */
ATA_HORKAGE_MAX_SEC_128 = (1 << 3), /* Limit max sects to 128 */
ATA_HORKAGE_BROKEN_HPA = (1 << 4), /* Broken HPA */
ATA_HORKAGE_DISABLE = (1 << 5), /* Disable it */
ATA_HORKAGE_HPA_SIZE = (1 << 6), /* native size off by one */
ATA_HORKAGE_IVB = (1 << 8), /* cbl det validity bit bugs */
ATA_HORKAGE_STUCK_ERR = (1 << 9), /* stuck ERR on next PACKET */
ATA_HORKAGE_BRIDGE_OK = (1 << 10), /* no bridge limits */
ATA_HORKAGE_ATAPI_MOD16_DMA = (1 << 11), /* use ATAPI DMA for commands
not multiple of 16 bytes */
ATA_HORKAGE_FIRMWARE_WARN = (1 << 12), /* firmware update warning */
ATA_HORKAGE_1_5_GBPS = (1 << 13), /* force 1.5 Gbps */
ATA_HORKAGE_NOSETXFER = (1 << 14), /* skip SETXFER, SATA only */
ATA_HORKAGE_BROKEN_FPDMA_AA = (1 << 15), /* skip AA */
ATA_HORKAGE_DUMP_ID = (1 << 16), /* dump IDENTIFY data */
libata: Set max sector to 65535 for Slimtype DVD A DS8A8SH drive The Slimtype DVD A DS8A8SH drive locks up when max sector is smaller than 65535, and the blow backtrace is observed on locking up: INFO: task flush-8:32:1130 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. flush-8:32 D ffffffff8180cf60 0 1130 2 0x00000000 ffff880273aef618 0000000000000046 0000000000000005 ffff880273aee000 ffff880273aee000 ffff880273aeffd8 ffff880273aee010 ffff880273aee000 ffff880273aeffd8 ffff880273aee000 ffff88026e842ea0 ffff880274a10000 Call Trace: [<ffffffff8168fc2d>] schedule+0x5d/0x70 [<ffffffff8168fccc>] io_schedule+0x8c/0xd0 [<ffffffff81324461>] get_request+0x731/0x7d0 [<ffffffff8133dc60>] ? cfq_allow_merge+0x50/0x90 [<ffffffff81083aa0>] ? wake_up_bit+0x40/0x40 [<ffffffff81320443>] ? bio_attempt_back_merge+0x33/0x110 [<ffffffff813248ea>] blk_queue_bio+0x23a/0x3f0 [<ffffffff81322176>] generic_make_request+0xc6/0x120 [<ffffffff81322308>] submit_bio+0x138/0x160 [<ffffffff811d7596>] ? bio_alloc_bioset+0x96/0x120 [<ffffffff811d1f61>] submit_bh+0x1f1/0x220 [<ffffffff811d48b8>] __block_write_full_page+0x228/0x340 [<ffffffff811d3650>] ? attach_nobh_buffers+0xc0/0xc0 [<ffffffff811d8960>] ? I_BDEV+0x10/0x10 [<ffffffff811d8960>] ? I_BDEV+0x10/0x10 [<ffffffff811d4ab6>] block_write_full_page_endio+0xe6/0x100 [<ffffffff811d4ae5>] block_write_full_page+0x15/0x20 [<ffffffff811d9268>] blkdev_writepage+0x18/0x20 [<ffffffff81142527>] __writepage+0x17/0x40 [<ffffffff811438ba>] write_cache_pages+0x34a/0x4a0 [<ffffffff81142510>] ? set_page_dirty+0x70/0x70 [<ffffffff81143a61>] generic_writepages+0x51/0x80 [<ffffffff81143ab0>] do_writepages+0x20/0x50 [<ffffffff811c9ed6>] __writeback_single_inode+0xa6/0x2b0 [<ffffffff811ca861>] writeback_sb_inodes+0x311/0x4d0 [<ffffffff811caaa6>] __writeback_inodes_wb+0x86/0xd0 [<ffffffff811cad43>] wb_writeback+0x1a3/0x330 [<ffffffff816916cf>] ? _raw_spin_lock_irqsave+0x3f/0x50 [<ffffffff811b8362>] ? get_nr_inodes+0x52/0x70 [<ffffffff811cb0ac>] wb_do_writeback+0x1dc/0x260 [<ffffffff8168dd34>] ? schedule_timeout+0x204/0x240 [<ffffffff811cb232>] bdi_writeback_thread+0x102/0x2b0 [<ffffffff811cb130>] ? wb_do_writeback+0x260/0x260 [<ffffffff81083550>] kthread+0xc0/0xd0 [<ffffffff81083490>] ? kthread_worker_fn+0x1b0/0x1b0 [<ffffffff8169a3ec>] ret_from_fork+0x7c/0xb0 [<ffffffff81083490>] ? kthread_worker_fn+0x1b0/0x1b0 The above trace was triggered by "dd if=/dev/zero of=/dev/sr0 bs=2048 count=32768" It was previously working by accident, since another bug introduced by 4dce8ba94c7 (libata: Use 'bool' return value for ata_id_XXX) caused all drives to use maxsect=65535. Cc: stable@vger.kernel.org Signed-off-by: Shan Hai <shan.hai@windriver.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2013-03-18 09:30:44 +07:00
ATA_HORKAGE_MAX_SEC_LBA48 = (1 << 17), /* Set max sects to 65535 */
ATA_HORKAGE_ATAPI_DMADIR = (1 << 18), /* device requires dmadir */
ATA_HORKAGE_NO_NCQ_TRIM = (1 << 19), /* don't use queued TRIM */
ATA_HORKAGE_NOLPM = (1 << 20), /* don't use LPM */
ATA_HORKAGE_WD_BROKEN_LPM = (1 << 21), /* some WDs have broken LPM */
libata: Whitelist SSDs that are known to properly return zeroes after TRIM As defined, the DRAT (Deterministic Read After Trim) and RZAT (Return Zero After Trim) flags in the ATA Command Set are unreliable in the sense that they only define what happens if the device successfully executed the DSM TRIM command. TRIM is only advisory, however, and the device is free to silently ignore all or parts of the request. In practice this renders the DRAT and RZAT flags completely useless and because the results are unpredictable we decided to disable discard in MD for 3.18 to avoid the risk of data corruption. Hardware vendors in the real world obviously need better guarantees than what the standards bodies provide. Unfortuntely those guarantees are encoded in product requirements documents rather than somewhere we can key off of them programatically. So we are compelled to disabling discard_zeroes_data for all devices unless we explicitly have data to support whitelisting them. This patch whitelists SSDs from a few of the main vendors. None of the whitelists are based on written guarantees. They are purely based on empirical evidence collected from internal and external users that have tested or qualified these drives in RAID deployments. The whitelist is only meant as a starting point and is by no means comprehensive: - All intel SSD models except for 510 - Micron M5?0/M600 - Samsung SSDs - Seagate SSDs Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Tejun Heo <tj@kernel.org>
2015-01-08 22:34:27 +07:00
ATA_HORKAGE_ZERO_AFTER_TRIM = (1 << 22),/* guarantees zero after trim */
ATA_HORKAGE_NO_DMA_LOG = (1 << 23), /* don't use DMA for log read */
ATA_HORKAGE_NOTRIM = (1 << 24), /* don't use TRIM */
ATA_HORKAGE_MAX_SEC_1024 = (1 << 25), /* Limit max sects to 1024 */
/* DMA mask for user DMA control: User visible values; DO NOT
renumber */
ATA_DMA_MASK_ATA = (1 << 0), /* DMA on ATA Disk */
ATA_DMA_MASK_ATAPI = (1 << 1), /* DMA on ATAPI */
ATA_DMA_MASK_CFA = (1 << 2), /* DMA on CF Card */
/* ATAPI command types */
ATAPI_READ = 0, /* READs */
ATAPI_WRITE = 1, /* WRITEs */
ATAPI_READ_CD = 2, /* READ CD [MSF] */
ATAPI_PASS_THRU = 3, /* SAT pass-thru */
ATAPI_MISC = 4, /* the rest */
/* Timing constants */
ATA_TIMING_SETUP = (1 << 0),
ATA_TIMING_ACT8B = (1 << 1),
ATA_TIMING_REC8B = (1 << 2),
ATA_TIMING_CYC8B = (1 << 3),
ATA_TIMING_8BIT = ATA_TIMING_ACT8B | ATA_TIMING_REC8B |
ATA_TIMING_CYC8B,
ATA_TIMING_ACTIVE = (1 << 4),
ATA_TIMING_RECOVER = (1 << 5),
ATA_TIMING_DMACK_HOLD = (1 << 6),
ATA_TIMING_CYCLE = (1 << 7),
ATA_TIMING_UDMA = (1 << 8),
ATA_TIMING_ALL = ATA_TIMING_SETUP | ATA_TIMING_ACT8B |
ATA_TIMING_REC8B | ATA_TIMING_CYC8B |
ATA_TIMING_ACTIVE | ATA_TIMING_RECOVER |
ATA_TIMING_DMACK_HOLD | ATA_TIMING_CYCLE |
ATA_TIMING_UDMA,
/* ACPI constants */
ATA_ACPI_FILTER_SETXFER = 1 << 0,
ATA_ACPI_FILTER_LOCK = 1 << 1,
ATA_ACPI_FILTER_DIPM = 1 << 2,
ATA_ACPI_FILTER_FPDMA_OFFSET = 1 << 3, /* FPDMA non-zero offset */
ATA_ACPI_FILTER_FPDMA_AA = 1 << 4, /* FPDMA auto activate */
ATA_ACPI_FILTER_DEFAULT = ATA_ACPI_FILTER_SETXFER |
ATA_ACPI_FILTER_LOCK |
ATA_ACPI_FILTER_DIPM,
};
enum ata_xfer_mask {
ATA_MASK_PIO = ((1LU << ATA_NR_PIO_MODES) - 1)
<< ATA_SHIFT_PIO,
ATA_MASK_MWDMA = ((1LU << ATA_NR_MWDMA_MODES) - 1)
<< ATA_SHIFT_MWDMA,
ATA_MASK_UDMA = ((1LU << ATA_NR_UDMA_MODES) - 1)
<< ATA_SHIFT_UDMA,
};
enum hsm_task_states {
HSM_ST_IDLE, /* no command on going */
HSM_ST_FIRST, /* (waiting the device to)
write CDB or first data block */
HSM_ST, /* (waiting the device to) transfer data */
HSM_ST_LAST, /* (waiting the device to) complete command */
HSM_ST_ERR, /* error */
};
enum ata_completion_errors {
AC_ERR_DEV = (1 << 0), /* device reported error */
AC_ERR_HSM = (1 << 1), /* host state machine violation */
AC_ERR_TIMEOUT = (1 << 2), /* timeout */
AC_ERR_MEDIA = (1 << 3), /* media error */
AC_ERR_ATA_BUS = (1 << 4), /* ATA bus error */
AC_ERR_HOST_BUS = (1 << 5), /* host bus error */
AC_ERR_SYSTEM = (1 << 6), /* system error */
AC_ERR_INVALID = (1 << 7), /* invalid argument */
AC_ERR_OTHER = (1 << 8), /* unknown */
AC_ERR_NODEV_HINT = (1 << 9), /* polling device detection hint */
AC_ERR_NCQ = (1 << 10), /* marker for offending NCQ qc */
};
/*
* Link power management policy: If you alter this, you also need to
* alter libata-scsi.c (for the ascii descriptions)
*/
enum ata_lpm_policy {
ATA_LPM_UNKNOWN,
ATA_LPM_MAX_POWER,
ATA_LPM_MED_POWER,
libata: Add new med_power_with_dipm link_power_management_policy setting As described by Matthew Garret quite a while back: https://mjg59.dreamwidth.org/34868.html Intel CPUs starting with the Haswell generation need SATA links to power down for the "package" part of the CPU to reach low power-states like PC7 / P8 which bring a significant power-saving with them. The default max_performance lpm policy does not allow for these high PC states, both the medium_power and min_power policies do allow this. The min_power policy saves significantly more power, but there are some reports of some disks / SSDs not liking min_power leading to system crashes and in some cases even data corruption has been reported. Matthew has found a document documenting the default settings of Intel's IRST Windows driver with which most laptops ship: https://www-ssl.intel.com/content/dam/doc/reference-guide/sata-devices-implementation-recommendations.pdf Matthew wrote a patch changing med_power to match those defaults, but that never got anywhere as some people where reporting issues with the patch-set that patch was a part of. This commit is another attempt to make the default IRST driver settings available under Linux, but instead of changing medium_power and potentially introducing regressions, this commit adds a new med_power_with_dipm setting which is identical to the existing medium_power accept that it enables dipm on top, which makes it match the Windows IRST driver settings, which should hopefully be safe to use on most devices. The med_power_with_dipm setting is close to min_power, except that: a) It does not use host-initiated slumber mode (ASP not set), but it does allow device-initiated slumber b) It does not enable DevSlp mode On my T440s test laptop I get the following power savings when idle: medium_power 0.9W med_power_with_dipm 1.2W min_power 1.2W Suggested-by: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2017-09-14 17:35:36 +07:00
ATA_LPM_MED_POWER_WITH_DIPM, /* Med power + DIPM as win IRST does */
ATA_LPM_MIN_POWER,
};
libata: reimplement link power management The current LPM implementation has the following issues. * Operation order isn't well thought-out. e.g. HIPM should be configured after IPM in SControl is properly configured. Not the other way around. * Suspend/resume paths call ata_lpm_enable/disable() which must only be called from EH context directly. Also, ata_lpm_enable/disable() were called whether LPM was in use or not. * Implementation is per-port when it should be per-link. As a result, it can't be used for controllers with slave links or PMP. * LPM state isn't managed consistently. After a link reset for whatever reason including suspend/resume the actual LPM state would be reset leaving ap->lpm_policy inconsistent. * Generic/driver-specific logic boundary isn't clear. Currently, libahci has to mangle stuff which libata EH proper should be handling. This makes the implementation unnecessarily complex and fragile. * Tied to ALPM. Doesn't consider DIPM only cases and doesn't check whether the device allows HIPM. * Error handling isn't implemented. Given the extent of mismatch with the rest of libata, I don't think trying to fix it piecewise makes much sense. This patch reimplements LPM support. * The new implementation is per-link. The target policy is still port-wide (ap->target_lpm_policy) but all the mechanisms and states are per-link and integrate well with the rest of link abstraction and can work with slave and PMP links. * Core EH has proper control of LPM state. LPM state is reconfigured when and only when reconfiguration is necessary. It makes sure that LPM state is reset when probing for new device on the link. Controller agnostic logic is now implemented in libata EH proper and driver implementation only has to deal with controller specifics. * Proper error handling. LPM config failure is attributed to the device on the link and LPM is disabled for the link if it fails repeatedly. * ops->enable/disable_pm() are replaced with single ops->set_lpm() which takes @policy and @hints. This simplifies driver specific implementation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-01 22:50:06 +07:00
enum ata_lpm_hints {
ATA_LPM_EMPTY = (1 << 0), /* port empty/probing */
ATA_LPM_HIPM = (1 << 1), /* may use HIPM */
ATA_LPM_WAKE_ONLY = (1 << 2), /* only wake up link */
libata: reimplement link power management The current LPM implementation has the following issues. * Operation order isn't well thought-out. e.g. HIPM should be configured after IPM in SControl is properly configured. Not the other way around. * Suspend/resume paths call ata_lpm_enable/disable() which must only be called from EH context directly. Also, ata_lpm_enable/disable() were called whether LPM was in use or not. * Implementation is per-port when it should be per-link. As a result, it can't be used for controllers with slave links or PMP. * LPM state isn't managed consistently. After a link reset for whatever reason including suspend/resume the actual LPM state would be reset leaving ap->lpm_policy inconsistent. * Generic/driver-specific logic boundary isn't clear. Currently, libahci has to mangle stuff which libata EH proper should be handling. This makes the implementation unnecessarily complex and fragile. * Tied to ALPM. Doesn't consider DIPM only cases and doesn't check whether the device allows HIPM. * Error handling isn't implemented. Given the extent of mismatch with the rest of libata, I don't think trying to fix it piecewise makes much sense. This patch reimplements LPM support. * The new implementation is per-link. The target policy is still port-wide (ap->target_lpm_policy) but all the mechanisms and states are per-link and integrate well with the rest of link abstraction and can work with slave and PMP links. * Core EH has proper control of LPM state. LPM state is reconfigured when and only when reconfiguration is necessary. It makes sure that LPM state is reset when probing for new device on the link. Controller agnostic logic is now implemented in libata EH proper and driver implementation only has to deal with controller specifics. * Proper error handling. LPM config failure is attributed to the device on the link and LPM is disabled for the link if it fails repeatedly. * ops->enable/disable_pm() are replaced with single ops->set_lpm() which takes @policy and @hints. This simplifies driver specific implementation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-01 22:50:06 +07:00
};
/* forward declarations */
struct scsi_device;
struct ata_port_operations;
struct ata_port;
struct ata_link;
struct ata_queued_cmd;
/* typedefs */
typedef void (*ata_qc_cb_t) (struct ata_queued_cmd *qc);
typedef int (*ata_prereset_fn_t)(struct ata_link *link, unsigned long deadline);
typedef int (*ata_reset_fn_t)(struct ata_link *link, unsigned int *classes,
libata: add deadline support to prereset and reset methods Add @deadline to prereset and reset methods and make them honor it. ata_wait_ready() which directly takes @deadline is implemented to be used as the wait function. This patch is in preparation for EH timing improvements. * ata_wait_ready() never does busy sleep. It's only used from EH and no wait in EH is that urgent. This function also prints 'be patient' message automatically after 5 secs of waiting if more than 3 secs is remaining till deadline. * ata_bus_post_reset() now fails with error code if any of its wait fails. This is important because earlier reset tries will have shorter timeout than the spec requires. If a device fails to respond before the short timeout, reset should be retried with longer timeout rather than silently ignoring the device. There are three behavior differences. 1. Timeout is applied to both devices at once, not separately. This is more consistent with what the spec says. 2. When a device passes devchk but fails to become ready before deadline. Previouly, post_reset would just succeed and let device classification remove the device. New code fails the reset thus causing reset retry. After a few times, EH will give up disabling the port. 3. When slave device passes devchk but fails to become accessible (TF-wise) after reset. Original code disables dev1 after 30s timeout and continues as if the device doesn't exist, while the patched code fails reset. When this happens, new code fails reset on whole port rather than proceeding with only the primary device. If the failing device is suffering transient problems, new code retries reset which is a better behavior. If the failing device is actually broken, the net effect is identical to it, but not to the other device sharing the channel. In the previous code, reset would have succeeded after 30s thus detecting the working one. In the new code, reset fails and whole port gets disabled. IMO, it's a pathological case anyway (broken device sharing bus with working one) and doesn't really matter. * ata_bus_softreset() is changed to return error code from ata_bus_post_reset(). It used to return 0 unconditionally. * Spin up waiting is to be removed and not converted to honor deadline. * To be on the safe side, deadline is set to 40s for the time being. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-02 14:50:52 +07:00
unsigned long deadline);
typedef void (*ata_postreset_fn_t)(struct ata_link *link, unsigned int *classes);
extern struct device_attribute dev_attr_link_power_management_policy;
extern struct device_attribute dev_attr_unload_heads;
extern struct device_attribute dev_attr_ncq_prio_enable;
extern struct device_attribute dev_attr_em_message_type;
extern struct device_attribute dev_attr_em_message;
extern struct device_attribute dev_attr_sw_activity;
enum sw_activity {
OFF,
BLINK_ON,
BLINK_OFF,
};
struct ata_taskfile {
unsigned long flags; /* ATA_TFLAG_xxx */
u8 protocol; /* ATA_PROT_xxx */
u8 ctl; /* control reg */
u8 hob_feature; /* additional data */
u8 hob_nsect; /* to support LBA48 */
u8 hob_lbal;
u8 hob_lbam;
u8 hob_lbah;
u8 feature;
u8 nsect;
u8 lbal;
u8 lbam;
u8 lbah;
u8 device;
u8 command; /* IO operation */
u32 auxiliary; /* auxiliary field */
/* from SATA 3.1 and */
/* ATA-8 ACS-3 */
};
#ifdef CONFIG_ATA_SFF
struct ata_ioports {
void __iomem *cmd_addr;
void __iomem *data_addr;
void __iomem *error_addr;
void __iomem *feature_addr;
void __iomem *nsect_addr;
void __iomem *lbal_addr;
void __iomem *lbam_addr;
void __iomem *lbah_addr;
void __iomem *device_addr;
void __iomem *status_addr;
void __iomem *command_addr;
void __iomem *altstatus_addr;
void __iomem *ctl_addr;
#ifdef CONFIG_ATA_BMDMA
void __iomem *bmdma_addr;
#endif /* CONFIG_ATA_BMDMA */
void __iomem *scr_addr;
};
#endif /* CONFIG_ATA_SFF */
struct ata_host {
spinlock_t lock;
struct device *dev;
void __iomem * const *iomap;
unsigned int n_ports;
libata: introduce ata_host->n_tags to avoid oops on SAS controllers 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") directly used ata_port->scsi_host->can_queue from ata_qc_new() to determine the number of tags supported by the host; unfortunately, SAS controllers doing SATA don't initialize ->scsi_host leading to the following oops. BUG: unable to handle kernel NULL pointer dereference at 0000000000000058 IP: [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 PGD 0 Oops: 0002 [#1] SMP Modules linked in: isci libsas scsi_transport_sas mgag200 drm_kms_helper ttm CPU: 1 PID: 518 Comm: udevd Not tainted 3.16.0-rc6+ #62 Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.02.0002.122320131210 12/23/2013 task: ffff880c1a00b280 ti: ffff88061a000000 task.ti: ffff88061a000000 RIP: 0010:[<ffffffff814e0618>] [<ffffffff814e0618>] ata_qc_new_init+0x188/0x1b0 RSP: 0018:ffff88061a003ae8 EFLAGS: 00010012 RAX: 0000000000000001 RBX: ffff88000241ca80 RCX: 00000000000000fa RDX: 0000000000000020 RSI: 0000000000000020 RDI: ffff8806194aa298 RBP: ffff88061a003ae8 R08: ffff8806194a8000 R09: 0000000000000000 R10: 0000000000000000 R11: ffff88000241ca80 R12: ffff88061ad58200 R13: ffff8806194aa298 R14: ffffffff814e67a0 R15: ffff8806194a8000 FS: 00007f3ad7fe3840(0000) GS:ffff880627620000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000058 CR3: 000000061a118000 CR4: 00000000001407e0 Stack: ffff88061a003b20 ffffffff814e96e1 ffff88000241ca80 ffff88061ad58200 ffff8800b6bf6000 ffff880c1c988000 ffff880619903850 ffff88061a003b68 ffffffffa0056ce1 ffff88061a003b48 0000000013d6e6f8 ffff88000241ca80 Call Trace: [<ffffffff814e96e1>] ata_sas_queuecmd+0xa1/0x430 [<ffffffffa0056ce1>] sas_queuecommand+0x191/0x220 [libsas] [<ffffffff8149afee>] scsi_dispatch_cmd+0x10e/0x300 [<ffffffff814a3bc5>] scsi_request_fn+0x2f5/0x550 [<ffffffff81317613>] __blk_run_queue+0x33/0x40 [<ffffffff8131781a>] queue_unplugged+0x2a/0x90 [<ffffffff8131ceb4>] blk_flush_plug_list+0x1b4/0x210 [<ffffffff8131d274>] blk_finish_plug+0x14/0x50 [<ffffffff8117eaa8>] __do_page_cache_readahead+0x198/0x1f0 [<ffffffff8117ee21>] force_page_cache_readahead+0x31/0x50 [<ffffffff8117ee7e>] page_cache_sync_readahead+0x3e/0x50 [<ffffffff81172ac6>] generic_file_read_iter+0x496/0x5a0 [<ffffffff81219897>] blkdev_read_iter+0x37/0x40 [<ffffffff811e307e>] new_sync_read+0x7e/0xb0 [<ffffffff811e3734>] vfs_read+0x94/0x170 [<ffffffff811e43c6>] SyS_read+0x46/0xb0 [<ffffffff811e33d1>] ? SyS_lseek+0x91/0xb0 [<ffffffff8171ee29>] system_call_fastpath+0x16/0x1b Code: 00 00 00 88 50 29 83 7f 08 01 19 d2 83 e2 f0 83 ea 50 88 50 34 c6 81 1d 02 00 00 40 c6 81 17 02 00 00 00 5d c3 66 0f 1f 44 00 00 <89> 14 25 58 00 00 00 Fix it by introducing ata_host->n_tags which is initialized to ATA_MAX_QUEUE - 1 in ata_host_init() for SAS controllers and set to scsi_host_template->can_queue in ata_host_register() for !SAS ones. As SAS hosts are never registered, this will give them the same ATA_MAX_QUEUE - 1 as before. Note that we can't use scsi_host->can_queue directly for SAS hosts anyway as they can go higher than the libata maximum. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com> Reported-by: Jesse Brandeburg <jesse.brandeburg@gmail.com> Reported-by: Peter Hurley <peter@hurleysoftware.com> Reported-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru> Fixes: 1871ee134b73 ("libata: support the ata host which implements a queue depth less than 32") Cc: Kevin Hao <haokexin@gmail.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: stable@vger.kernel.org
2014-07-23 20:05:27 +07:00
unsigned int n_tags; /* nr of NCQ tags */
void *private_data;
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:49 +07:00
struct ata_port_operations *ops;
unsigned long flags;
struct kref kref;
libata: implement cross-port EH exclusion In libata, the non-EH code paths should always take and release ap->lock explicitly when accessing hardware or shared data structures. However, once EH is active, it's assumed that the port is owned by EH and EH methods don't explicitly take ap->lock unless race from irq handler or other code paths are expected. However, libata EH didn't guarantee exclusion among EHs for ports of the same host. IOW, multiple EHs may execute in parallel on multiple ports of the same controller. In many cases, especially in SATA, the ports are completely independent of each other and this doesn't cause problems; however, there are cases where different ports share the same resource, which lead to obscure timing related bugs such as the one fixed by commit 213373cf (ata_piix: fix locking around SIDPR access). This patch implements exclusion among EHs of the same host. When EH begins, it acquires per-host EH ownership by calling ata_eh_acquire(). When EH finishes, the ownership is released by calling ata_eh_release(). EH ownership is also released whenever the EH thread goes to sleep from ata_msleep() or explicitly and reacquired after waking up. This ensures that while EH is actively accessing the hardware, it has exclusive access to it while allowing EHs to interleave and progress in parallel as they hit waiting stages, which dominate the time spent in EH. This achieves cross-port EH exclusion without pervasive and fragile changes while still allowing parallel EH for the most part. This was first reported by yuanding02@gmail.com more than three years ago in the following bugzilla. :-) https://bugzilla.kernel.org/show_bug.cgi?id=8223 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Reported-by: yuanding02@gmail.com Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-06 22:57:14 +07:00
struct mutex eh_mutex;
struct task_struct *eh_owner;
struct ata_port *simplex_claimed; /* channel owning the DMA */
struct ata_port *ports[0];
};
struct ata_queued_cmd {
struct ata_port *ap;
struct ata_device *dev;
struct scsi_cmnd *scsicmd;
void (*scsidone)(struct scsi_cmnd *);
struct ata_taskfile tf;
u8 cdb[ATAPI_CDB_LEN];
unsigned long flags; /* ATA_QCFLAG_xxx */
unsigned int tag;
unsigned int n_elem;
unsigned int orig_n_elem;
int dma_dir;
unsigned int sect_size;
unsigned int nbytes;
unsigned int extrabytes;
unsigned int curbytes;
struct scatterlist sgent;
struct scatterlist *sg;
struct scatterlist *cursg;
unsigned int cursg_ofs;
unsigned int err_mask;
struct ata_taskfile result_tf;
ata_qc_cb_t complete_fn;
void *private_data;
void *lldd_task;
};
struct ata_port_stats {
unsigned long unhandled_irq;
unsigned long idle_irq;
unsigned long rw_reqbuf;
};
struct ata_ering_entry {
unsigned int eflags;
unsigned int err_mask;
u64 timestamp;
};
struct ata_ering {
int cursor;
struct ata_ering_entry ring[ATA_ERING_SIZE];
};
struct ata_device {
struct ata_link *link;
unsigned int devno; /* 0 or 1 */
unsigned int horkage; /* List of broken features */
unsigned long flags; /* ATA_DFLAG_xxx */
struct scsi_device *sdev; /* attached SCSI device */
void *private_data;
#ifdef CONFIG_ATA_ACPI
union acpi_object *gtf_cache;
unsigned int gtf_filter;
#endif
#ifdef CONFIG_SATA_ZPODD
void *zpodd;
#endif
struct device tdev;
/* n_sector is CLEAR_BEGIN, read comment above CLEAR_BEGIN */
u64 n_sectors; /* size of device, if ATA */
u64 n_native_sectors; /* native size, if ATA */
unsigned int class; /* ATA_DEV_xxx */
unsigned long unpark_deadline;
u8 pio_mode;
u8 dma_mode;
u8 xfer_mode;
unsigned int xfer_shift; /* ATA_SHIFT_xxx */
unsigned int multi_count; /* sectors count for
READ/WRITE MULTIPLE */
unsigned int max_sectors; /* per-device max sectors */
unsigned int cdb_len;
/* per-dev xfer mask */
unsigned long pio_mask;
unsigned long mwdma_mask;
unsigned long udma_mask;
/* for CHS addressing */
u16 cylinders; /* Number of cylinders */
u16 heads; /* Number of heads */
u16 sectors; /* Number of sectors per track */
union {
u16 id[ATA_ID_WORDS]; /* IDENTIFY xxx DEVICE data */
u32 gscr[SATA_PMP_GSCR_DWORDS]; /* PMP GSCR block */
} ____cacheline_aligned;
/* DEVSLP Timing Variables from Identify Device Data Log */
u8 devslp_timing[ATA_LOG_DEVSLP_SIZE];
/* NCQ send and receive log subcommand support */
u8 ncq_send_recv_cmds[ATA_LOG_NCQ_SEND_RECV_SIZE];
u8 ncq_non_data_cmds[ATA_LOG_NCQ_NON_DATA_SIZE];
/* ZAC zone configuration */
u32 zac_zoned_cap;
u32 zac_zones_optimal_open;
u32 zac_zones_optimal_nonseq;
u32 zac_zones_max_open;
/* error history */
int spdn_cnt;
/* ering is CLEAR_END, read comment above CLEAR_END */
struct ata_ering ering;
};
/* Fields between ATA_DEVICE_CLEAR_BEGIN and ATA_DEVICE_CLEAR_END are
* cleared to zero on ata_dev_init().
*/
#define ATA_DEVICE_CLEAR_BEGIN offsetof(struct ata_device, n_sectors)
#define ATA_DEVICE_CLEAR_END offsetof(struct ata_device, ering)
struct ata_eh_info {
struct ata_device *dev; /* offending device */
u32 serror; /* SError from LLDD */
unsigned int err_mask; /* port-wide err_mask */
unsigned int action; /* ATA_EH_* action mask */
unsigned int dev_action[ATA_MAX_DEVICES]; /* dev EH action */
unsigned int flags; /* ATA_EHI_* flags */
unsigned int probe_mask;
char desc[ATA_EH_DESC_LEN];
int desc_len;
};
struct ata_eh_context {
struct ata_eh_info i;
int tries[ATA_MAX_DEVICES];
int cmd_timeout_idx[ATA_MAX_DEVICES]
[ATA_EH_CMD_TIMEOUT_TABLE_SIZE];
unsigned int classes[ATA_MAX_DEVICES];
unsigned int did_probe_mask;
unsigned int unloaded_mask;
unsigned int saved_ncq_enabled;
u8 saved_xfer_mode[ATA_MAX_DEVICES];
/* timestamp for the last reset attempt or success */
unsigned long last_reset;
};
struct ata_acpi_drive
{
u32 pio;
u32 dma;
} __packed;
struct ata_acpi_gtm {
struct ata_acpi_drive drive[2];
u32 flags;
} __packed;
struct ata_link {
struct ata_port *ap;
int pmp; /* port multiplier port # */
struct device tdev;
unsigned int active_tag; /* active tag on this link */
u32 sactive; /* active NCQ commands */
unsigned int flags; /* ATA_LFLAG_xxx */
u32 saved_scontrol; /* SControl on probe */
unsigned int hw_sata_spd_limit;
unsigned int sata_spd_limit;
unsigned int sata_spd; /* current SATA PHY speed */
libata: reimplement link power management The current LPM implementation has the following issues. * Operation order isn't well thought-out. e.g. HIPM should be configured after IPM in SControl is properly configured. Not the other way around. * Suspend/resume paths call ata_lpm_enable/disable() which must only be called from EH context directly. Also, ata_lpm_enable/disable() were called whether LPM was in use or not. * Implementation is per-port when it should be per-link. As a result, it can't be used for controllers with slave links or PMP. * LPM state isn't managed consistently. After a link reset for whatever reason including suspend/resume the actual LPM state would be reset leaving ap->lpm_policy inconsistent. * Generic/driver-specific logic boundary isn't clear. Currently, libahci has to mangle stuff which libata EH proper should be handling. This makes the implementation unnecessarily complex and fragile. * Tied to ALPM. Doesn't consider DIPM only cases and doesn't check whether the device allows HIPM. * Error handling isn't implemented. Given the extent of mismatch with the rest of libata, I don't think trying to fix it piecewise makes much sense. This patch reimplements LPM support. * The new implementation is per-link. The target policy is still port-wide (ap->target_lpm_policy) but all the mechanisms and states are per-link and integrate well with the rest of link abstraction and can work with slave and PMP links. * Core EH has proper control of LPM state. LPM state is reconfigured when and only when reconfiguration is necessary. It makes sure that LPM state is reset when probing for new device on the link. Controller agnostic logic is now implemented in libata EH proper and driver implementation only has to deal with controller specifics. * Proper error handling. LPM config failure is attributed to the device on the link and LPM is disabled for the link if it fails repeatedly. * ops->enable/disable_pm() are replaced with single ops->set_lpm() which takes @policy and @hints. This simplifies driver specific implementation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-01 22:50:06 +07:00
enum ata_lpm_policy lpm_policy;
/* record runtime error info, protected by host_set lock */
struct ata_eh_info eh_info;
/* EH context */
struct ata_eh_context eh_context;
struct ata_device device[ATA_MAX_DEVICES];
unsigned long last_lpm_change; /* when last LPM change happened */
};
#define ATA_LINK_CLEAR_BEGIN offsetof(struct ata_link, active_tag)
#define ATA_LINK_CLEAR_END offsetof(struct ata_link, device[0])
struct ata_port {
struct Scsi_Host *scsi_host; /* our co-allocated scsi host */
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:49 +07:00
struct ata_port_operations *ops;
spinlock_t *lock;
/* Flags owned by the EH context. Only EH should touch these once the
port is active */
unsigned long flags; /* ATA_FLAG_xxx */
/* Flags that change dynamically, protected by ap->lock */
unsigned int pflags; /* ATA_PFLAG_xxx */
unsigned int print_id; /* user visible unique port ID */
unsigned int local_port_no; /* host local port num */
unsigned int port_no; /* 0 based port no. inside the host */
#ifdef CONFIG_ATA_SFF
struct ata_ioports ioaddr; /* ATA cmd/ctl/dma register blocks */
u8 ctl; /* cache of ATA control register */
u8 last_ctl; /* Cache last written value */
struct ata_link* sff_pio_task_link; /* link currently used */
struct delayed_work sff_pio_task;
#ifdef CONFIG_ATA_BMDMA
struct ata_bmdma_prd *bmdma_prd; /* BMDMA SG list */
dma_addr_t bmdma_prd_dma; /* and its DMA mapping */
#endif /* CONFIG_ATA_BMDMA */
#endif /* CONFIG_ATA_SFF */
unsigned int pio_mask;
unsigned int mwdma_mask;
unsigned int udma_mask;
unsigned int cbl; /* cable type; ATA_CBL_xxx */
struct ata_queued_cmd qcmd[ATA_MAX_QUEUE];
unsigned long sas_tag_allocated; /* for sas tag allocation only */
unsigned int qc_active;
int nr_active_links; /* #links with active qcs */
unsigned int sas_last_tag; /* track next tag hw expects */
libata: implement slave_link Explanation taken from the comment of ata_slave_link_init(). In libata, a port contains links and a link contains devices. There is single host link but if a PMP is attached to it, there can be multiple fan-out links. On SATA, there's usually a single device connected to a link but PATA and SATA controllers emulating TF based interface can have two - master and slave. However, there are a few controllers which don't fit into this abstraction too well - SATA controllers which emulate TF interface with both master and slave devices but also have separate SCR register sets for each device. These controllers need separate links for physical link handling (e.g. onlineness, link speed) but should be treated like a traditional M/S controller for everything else (e.g. command issue, softreset). slave_link is libata's way of handling this class of controllers without impacting core layer too much. For anything other than physical link handling, the default host link is used for both master and slave. For physical link handling, separate @ap->slave_link is used. All dirty details are implemented inside libata core layer. From LLD's POV, the only difference is that prereset, hardreset and postreset are called once more for the slave link, so the reset sequence looks like the following. prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) -> softreset(M) -> postreset(M) -> postreset(S) Note that softreset is called only for the master. Softreset resets both M/S by definition, so SRST on master should handle both (the standard method will work just fine). As slave_link excludes PMP support and only code paths which deal with the attributes of physical link are affected, all the changes are localized to libata.h, libata-core.c and libata-eh.c. * ata_is_host_link() updated so that slave_link is considered as host link too. * iterator extended to iterate over the slave_link when using the underbarred version. * force param handling updated such that devno 16 is mapped to the slave link/device. * ata_link_on/offline() updated to return the combined result from master and slave link. ata_phys_link_on/offline() are the direct versions. * EH autopsy and report are performed separately for master slave links. Reset is udpated to implement the above described reset sequence. Except for reset update, most changes are minor, many of them just modifying dev->link to ata_dev_phys_link(dev) or using phys online test instead. After this update, LLDs can take full advantage of per-dev SCR registers by simply turning on slave link. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 15:02:43 +07:00
struct ata_link link; /* host default link */
struct ata_link *slave_link; /* see ata_slave_link_init() */
int nr_pmp_links; /* nr of available PMP links */
struct ata_link *pmp_link; /* array of PMP links */
struct ata_link *excl_link; /* for PMP qc exclusion */
struct ata_port_stats stats;
struct ata_host *host;
struct device *dev;
struct device tdev;
struct mutex scsi_scan_mutex;
struct delayed_work hotplug_task;
struct work_struct scsi_rescan_task;
unsigned int hsm_task_state;
u32 msg_enable;
struct list_head eh_done_q;
wait_queue_head_t eh_wait_q;
int eh_tries;
struct completion park_req_pending;
pm_message_t pm_mesg;
libata: reimplement link power management The current LPM implementation has the following issues. * Operation order isn't well thought-out. e.g. HIPM should be configured after IPM in SControl is properly configured. Not the other way around. * Suspend/resume paths call ata_lpm_enable/disable() which must only be called from EH context directly. Also, ata_lpm_enable/disable() were called whether LPM was in use or not. * Implementation is per-port when it should be per-link. As a result, it can't be used for controllers with slave links or PMP. * LPM state isn't managed consistently. After a link reset for whatever reason including suspend/resume the actual LPM state would be reset leaving ap->lpm_policy inconsistent. * Generic/driver-specific logic boundary isn't clear. Currently, libahci has to mangle stuff which libata EH proper should be handling. This makes the implementation unnecessarily complex and fragile. * Tied to ALPM. Doesn't consider DIPM only cases and doesn't check whether the device allows HIPM. * Error handling isn't implemented. Given the extent of mismatch with the rest of libata, I don't think trying to fix it piecewise makes much sense. This patch reimplements LPM support. * The new implementation is per-link. The target policy is still port-wide (ap->target_lpm_policy) but all the mechanisms and states are per-link and integrate well with the rest of link abstraction and can work with slave and PMP links. * Core EH has proper control of LPM state. LPM state is reconfigured when and only when reconfiguration is necessary. It makes sure that LPM state is reset when probing for new device on the link. Controller agnostic logic is now implemented in libata EH proper and driver implementation only has to deal with controller specifics. * Proper error handling. LPM config failure is attributed to the device on the link and LPM is disabled for the link if it fails repeatedly. * ops->enable/disable_pm() are replaced with single ops->set_lpm() which takes @policy and @hints. This simplifies driver specific implementation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-01 22:50:06 +07:00
enum ata_lpm_policy target_lpm_policy;
struct timer_list fastdrain_timer;
unsigned long fastdrain_cnt;
int em_message_type;
void *private_data;
#ifdef CONFIG_ATA_ACPI
struct ata_acpi_gtm __acpi_init_gtm; /* use ata_acpi_init_gtm() */
#endif
/* owned by EH */
u8 sector_buf[ATA_SECT_SIZE] ____cacheline_aligned;
};
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:49 +07:00
/* The following initializer overrides a method to NULL whether one of
* its parent has the method defined or not. This is equivalent to
* ERR_PTR(-ENOENT). Unfortunately, ERR_PTR doesn't render a constant
* expression and thus can't be used as an initializer.
*/
#define ATA_OP_NULL (void *)(unsigned long)(-ENOENT)
struct ata_port_operations {
/*
* Command execution
*/
int (*qc_defer)(struct ata_queued_cmd *qc);
int (*check_atapi_dma)(struct ata_queued_cmd *qc);
void (*qc_prep)(struct ata_queued_cmd *qc);
unsigned int (*qc_issue)(struct ata_queued_cmd *qc);
bool (*qc_fill_rtf)(struct ata_queued_cmd *qc);
/*
* Configuration and exception handling
*/
int (*cable_detect)(struct ata_port *ap);
unsigned long (*mode_filter)(struct ata_device *dev, unsigned long xfer_mask);
void (*set_piomode)(struct ata_port *ap, struct ata_device *dev);
void (*set_dmamode)(struct ata_port *ap, struct ata_device *dev);
int (*set_mode)(struct ata_link *link, struct ata_device **r_failed_dev);
unsigned int (*read_id)(struct ata_device *dev, struct ata_taskfile *tf, u16 *id);
void (*dev_config)(struct ata_device *dev);
void (*freeze)(struct ata_port *ap);
void (*thaw)(struct ata_port *ap);
libata: make reset related methods proper port operations Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:50 +07:00
ata_prereset_fn_t prereset;
ata_reset_fn_t softreset;
ata_reset_fn_t hardreset;
ata_postreset_fn_t postreset;
ata_prereset_fn_t pmp_prereset;
ata_reset_fn_t pmp_softreset;
ata_reset_fn_t pmp_hardreset;
ata_postreset_fn_t pmp_postreset;
void (*error_handler)(struct ata_port *ap);
void (*lost_interrupt)(struct ata_port *ap);
void (*post_internal_cmd)(struct ata_queued_cmd *qc);
void (*sched_eh)(struct ata_port *ap);
void (*end_eh)(struct ata_port *ap);
/*
* Optional features
*/
int (*scr_read)(struct ata_link *link, unsigned int sc_reg, u32 *val);
int (*scr_write)(struct ata_link *link, unsigned int sc_reg, u32 val);
void (*pmp_attach)(struct ata_port *ap);
void (*pmp_detach)(struct ata_port *ap);
libata: reimplement link power management The current LPM implementation has the following issues. * Operation order isn't well thought-out. e.g. HIPM should be configured after IPM in SControl is properly configured. Not the other way around. * Suspend/resume paths call ata_lpm_enable/disable() which must only be called from EH context directly. Also, ata_lpm_enable/disable() were called whether LPM was in use or not. * Implementation is per-port when it should be per-link. As a result, it can't be used for controllers with slave links or PMP. * LPM state isn't managed consistently. After a link reset for whatever reason including suspend/resume the actual LPM state would be reset leaving ap->lpm_policy inconsistent. * Generic/driver-specific logic boundary isn't clear. Currently, libahci has to mangle stuff which libata EH proper should be handling. This makes the implementation unnecessarily complex and fragile. * Tied to ALPM. Doesn't consider DIPM only cases and doesn't check whether the device allows HIPM. * Error handling isn't implemented. Given the extent of mismatch with the rest of libata, I don't think trying to fix it piecewise makes much sense. This patch reimplements LPM support. * The new implementation is per-link. The target policy is still port-wide (ap->target_lpm_policy) but all the mechanisms and states are per-link and integrate well with the rest of link abstraction and can work with slave and PMP links. * Core EH has proper control of LPM state. LPM state is reconfigured when and only when reconfiguration is necessary. It makes sure that LPM state is reset when probing for new device on the link. Controller agnostic logic is now implemented in libata EH proper and driver implementation only has to deal with controller specifics. * Proper error handling. LPM config failure is attributed to the device on the link and LPM is disabled for the link if it fails repeatedly. * ops->enable/disable_pm() are replaced with single ops->set_lpm() which takes @policy and @hints. This simplifies driver specific implementation. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-09-01 22:50:06 +07:00
int (*set_lpm)(struct ata_link *link, enum ata_lpm_policy policy,
unsigned hints);
/*
* Start, stop, suspend and resume
*/
int (*port_suspend)(struct ata_port *ap, pm_message_t mesg);
int (*port_resume)(struct ata_port *ap);
int (*port_start)(struct ata_port *ap);
void (*port_stop)(struct ata_port *ap);
void (*host_stop)(struct ata_host *host);
#ifdef CONFIG_ATA_SFF
/*
* SFF / taskfile oriented ops
*/
void (*sff_dev_select)(struct ata_port *ap, unsigned int device);
void (*sff_set_devctl)(struct ata_port *ap, u8 ctl);
u8 (*sff_check_status)(struct ata_port *ap);
u8 (*sff_check_altstatus)(struct ata_port *ap);
void (*sff_tf_load)(struct ata_port *ap, const struct ata_taskfile *tf);
void (*sff_tf_read)(struct ata_port *ap, struct ata_taskfile *tf);
void (*sff_exec_command)(struct ata_port *ap,
const struct ata_taskfile *tf);
unsigned int (*sff_data_xfer)(struct ata_queued_cmd *qc,
unsigned char *buf, unsigned int buflen, int rw);
void (*sff_irq_on)(struct ata_port *);
libata: implement spurious irq handling for SFF and apply it to piix Traditional IDE interface sucks in that it doesn't have a reliable IRQ pending bit, so if the controller raises IRQ while the driver is expecting it not to, the IRQ won't be cleared and eventually the IRQ line will be killed by interrupt subsystem. Some controllers have non-standard mechanism to indicate IRQ pending so that this condition can be detected and worked around. This patch adds an optional operation ->sff_irq_check() which will be called for each port from the ata_sff_interrupt() if an unexpected interrupt is received. If the operation returns %true, ->sff_check_status() and ->sff_irq_clear() will be cleared for the port. Note that this doesn't mark the interrupt as handled so it won't prevent IRQ subsystem from killing the IRQ if this mechanism fails to clear the spurious IRQ. This patch also implements ->sff_irq_check() for ata_piix. Note that this adds slight overhead to shared IRQ operation as IRQs which are destined for other controllers will trigger extra register accesses to check whether IDE interrupt is pending but this solves rare screaming IRQ cases and for some curious reason also helps weird BIOS related glitch on Samsung n130 as reported in bko#14314. http://bugzilla.kernel.org/show_bug.cgi?id=14314 * piix_base_ops dropped as suggested by Sergei. * Spurious IRQ detection doesn't kick in anymore if polling qc is in progress. This provides less protection but some controllers have possible data corruption issues if the wrong register is accessed while a command is in progress. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Johannes Stezenbach <js@sig21.net> Reported-by: Hans Werner <hwerner4@gmx.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-01-19 08:49:19 +07:00
bool (*sff_irq_check)(struct ata_port *);
void (*sff_irq_clear)(struct ata_port *);
void (*sff_drain_fifo)(struct ata_queued_cmd *qc);
#ifdef CONFIG_ATA_BMDMA
void (*bmdma_setup)(struct ata_queued_cmd *qc);
void (*bmdma_start)(struct ata_queued_cmd *qc);
void (*bmdma_stop)(struct ata_queued_cmd *qc);
u8 (*bmdma_status)(struct ata_port *ap);
#endif /* CONFIG_ATA_BMDMA */
#endif /* CONFIG_ATA_SFF */
ssize_t (*em_show)(struct ata_port *ap, char *buf);
ssize_t (*em_store)(struct ata_port *ap, const char *message,
size_t size);
ssize_t (*sw_activity_show)(struct ata_device *dev, char *buf);
ssize_t (*sw_activity_store)(struct ata_device *dev,
enum sw_activity val);
ssize_t (*transmit_led_message)(struct ata_port *ap, u32 state,
ssize_t size);
/*
* Obsolete
*/
void (*phy_reset)(struct ata_port *ap);
void (*eng_timeout)(struct ata_port *ap);
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:49 +07:00
/*
* ->inherits must be the last field and all the preceding
* fields must be pointers.
*/
const struct ata_port_operations *inherits;
};
struct ata_port_info {
unsigned long flags;
unsigned long link_flags;
unsigned long pio_mask;
unsigned long mwdma_mask;
unsigned long udma_mask;
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:49 +07:00
struct ata_port_operations *port_ops;
void *private_data;
};
struct ata_timing {
unsigned short mode; /* ATA mode */
unsigned short setup; /* t1 */
unsigned short act8b; /* t2 for 8-bit I/O */
unsigned short rec8b; /* t2i for 8-bit I/O */
unsigned short cyc8b; /* t0 for 8-bit I/O */
unsigned short active; /* t2 or tD */
unsigned short recover; /* t2i or tK */
unsigned short dmack_hold; /* tj */
unsigned short cycle; /* t0 */
unsigned short udma; /* t2CYCTYP/2 */
};
/*
* Core layer - drivers/ata/libata-core.c
*/
extern const unsigned long sata_deb_timing_normal[];
extern const unsigned long sata_deb_timing_hotplug[];
extern const unsigned long sata_deb_timing_long[];
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:49 +07:00
extern struct ata_port_operations ata_dummy_port_ops;
extern const struct ata_port_info ata_dummy_port_info;
static inline bool ata_is_atapi(u8 prot)
{
return prot & ATA_PROT_FLAG_ATAPI;
}
static inline bool ata_is_pio(u8 prot)
{
return prot & ATA_PROT_FLAG_PIO;
}
static inline bool ata_is_dma(u8 prot)
{
return prot & ATA_PROT_FLAG_DMA;
}
static inline bool ata_is_ncq(u8 prot)
{
return prot & ATA_PROT_FLAG_NCQ;
}
static inline bool ata_is_data(u8 prot)
{
return prot & (ATA_PROT_FLAG_PIO | ATA_PROT_FLAG_DMA);
}
static inline int is_multi_taskfile(struct ata_taskfile *tf)
{
return (tf->command == ATA_CMD_READ_MULTI) ||
(tf->command == ATA_CMD_WRITE_MULTI) ||
(tf->command == ATA_CMD_READ_MULTI_EXT) ||
(tf->command == ATA_CMD_WRITE_MULTI_EXT) ||
(tf->command == ATA_CMD_WRITE_MULTI_FUA_EXT);
}
static inline const unsigned long *
sata_ehc_deb_timing(struct ata_eh_context *ehc)
{
if (ehc->i.flags & ATA_EHI_HOTPLUGGED)
return sata_deb_timing_hotplug;
else
return sata_deb_timing_normal;
}
static inline int ata_port_is_dummy(struct ata_port *ap)
{
return ap->ops == &ata_dummy_port_ops;
}
extern int sata_set_spd(struct ata_link *link);
extern int ata_std_prereset(struct ata_link *link, unsigned long deadline);
extern int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
int (*check_ready)(struct ata_link *link));
extern int sata_link_debounce(struct ata_link *link,
const unsigned long *params, unsigned long deadline);
extern int sata_link_resume(struct ata_link *link, const unsigned long *params,
unsigned long deadline);
extern int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
bool spm_wakeup);
extern int sata_link_hardreset(struct ata_link *link,
const unsigned long *timing, unsigned long deadline,
bool *online, int (*check_ready)(struct ata_link *));
extern int sata_std_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
extern void ata_std_postreset(struct ata_link *link, unsigned int *classes);
extern struct ata_host *ata_host_alloc(struct device *dev, int max_ports);
extern struct ata_host *ata_host_alloc_pinfo(struct device *dev,
const struct ata_port_info * const * ppi, int n_ports);
libata: implement slave_link Explanation taken from the comment of ata_slave_link_init(). In libata, a port contains links and a link contains devices. There is single host link but if a PMP is attached to it, there can be multiple fan-out links. On SATA, there's usually a single device connected to a link but PATA and SATA controllers emulating TF based interface can have two - master and slave. However, there are a few controllers which don't fit into this abstraction too well - SATA controllers which emulate TF interface with both master and slave devices but also have separate SCR register sets for each device. These controllers need separate links for physical link handling (e.g. onlineness, link speed) but should be treated like a traditional M/S controller for everything else (e.g. command issue, softreset). slave_link is libata's way of handling this class of controllers without impacting core layer too much. For anything other than physical link handling, the default host link is used for both master and slave. For physical link handling, separate @ap->slave_link is used. All dirty details are implemented inside libata core layer. From LLD's POV, the only difference is that prereset, hardreset and postreset are called once more for the slave link, so the reset sequence looks like the following. prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) -> softreset(M) -> postreset(M) -> postreset(S) Note that softreset is called only for the master. Softreset resets both M/S by definition, so SRST on master should handle both (the standard method will work just fine). As slave_link excludes PMP support and only code paths which deal with the attributes of physical link are affected, all the changes are localized to libata.h, libata-core.c and libata-eh.c. * ata_is_host_link() updated so that slave_link is considered as host link too. * iterator extended to iterate over the slave_link when using the underbarred version. * force param handling updated such that devno 16 is mapped to the slave link/device. * ata_link_on/offline() updated to return the combined result from master and slave link. ata_phys_link_on/offline() are the direct versions. * EH autopsy and report are performed separately for master slave links. Reset is udpated to implement the above described reset sequence. Except for reset update, most changes are minor, many of them just modifying dev->link to ata_dev_phys_link(dev) or using phys online test instead. After this update, LLDs can take full advantage of per-dev SCR registers by simply turning on slave link. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 15:02:43 +07:00
extern int ata_slave_link_init(struct ata_port *ap);
extern int ata_host_start(struct ata_host *host);
extern int ata_host_register(struct ata_host *host,
struct scsi_host_template *sht);
extern int ata_host_activate(struct ata_host *host, int irq,
irq_handler_t irq_handler, unsigned long irq_flags,
struct scsi_host_template *sht);
extern void ata_host_detach(struct ata_host *host);
extern void ata_host_init(struct ata_host *, struct device *, struct ata_port_operations *);
extern int ata_scsi_detect(struct scsi_host_template *sht);
extern int ata_scsi_ioctl(struct scsi_device *dev, int cmd, void __user *arg);
extern int ata_scsi_queuecmd(struct Scsi_Host *h, struct scsi_cmnd *cmd);
extern int ata_sas_scsi_ioctl(struct ata_port *ap, struct scsi_device *dev,
int cmd, void __user *arg);
extern void ata_sas_port_destroy(struct ata_port *);
extern struct ata_port *ata_sas_port_alloc(struct ata_host *,
struct ata_port_info *, struct Scsi_Host *);
extern void ata_sas_async_probe(struct ata_port *ap);
extern int ata_sas_sync_probe(struct ata_port *ap);
extern int ata_sas_port_init(struct ata_port *);
extern int ata_sas_port_start(struct ata_port *ap);
extern void ata_sas_port_stop(struct ata_port *ap);
extern int ata_sas_slave_configure(struct scsi_device *, struct ata_port *);
extern int ata_sas_queuecmd(struct scsi_cmnd *cmd, struct ata_port *ap);
extern enum blk_eh_timer_return ata_scsi_timed_out(struct scsi_cmnd *cmd);
extern int sata_scr_valid(struct ata_link *link);
extern int sata_scr_read(struct ata_link *link, int reg, u32 *val);
extern int sata_scr_write(struct ata_link *link, int reg, u32 val);
extern int sata_scr_write_flush(struct ata_link *link, int reg, u32 val);
extern bool ata_link_online(struct ata_link *link);
extern bool ata_link_offline(struct ata_link *link);
#ifdef CONFIG_PM
extern int ata_host_suspend(struct ata_host *host, pm_message_t mesg);
extern void ata_host_resume(struct ata_host *host);
libata, libsas: kill pm_result and related cleanup Tejun says: "At least for libata, worrying about suspend/resume failures don't make whole lot of sense. If suspend failed, just proceed with suspend. If the device can't be woken up afterwards, that's that. There isn't anything we could have done differently anyway. The same for resume, if spinup fails, the device is dud and the following commands will invoke EH actions and will eventually fail. Again, there really isn't any *choice* to make. Just making sure the errors are handled gracefully (ie. don't crash) and the following commands are handled correctly should be enough." The only libata user that actually cares about the result from a suspend operation is libsas. However, it only cares about whether queuing a new operation collides with an in-flight one. All libsas does with the error is retry, but we can just let libata wait for the previous operation before continuing. Other cleanups include: 1/ Unifying all ata port pm operations on an ata_port_pm_ prefix 2/ Marking all ata port pm helper routines as returning void, only ata_port_pm_ entry points need to fake a 0 return value. 3/ Killing ata_port_{suspend|resume}_common() in favor of calling ata_port_request_pm() directly 4/ Killing the wrappers that just do a to_ata_port() conversion 5/ Clearly marking the entry points that do async operations with an _async suffix. Reference: http://marc.info/?l=linux-scsi&m=138995409532286&w=2 Cc: Phillip Susi <psusi@ubuntu.com> Cc: Alan Stern <stern@rowland.harvard.edu> Suggested-by: Tejun Heo <tj@kernel.org> Signed-off-by: Todd Brandt <todd.e.brandt@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-03-15 03:52:48 +07:00
extern void ata_sas_port_suspend(struct ata_port *ap);
extern void ata_sas_port_resume(struct ata_port *ap);
#else
libata, libsas: kill pm_result and related cleanup Tejun says: "At least for libata, worrying about suspend/resume failures don't make whole lot of sense. If suspend failed, just proceed with suspend. If the device can't be woken up afterwards, that's that. There isn't anything we could have done differently anyway. The same for resume, if spinup fails, the device is dud and the following commands will invoke EH actions and will eventually fail. Again, there really isn't any *choice* to make. Just making sure the errors are handled gracefully (ie. don't crash) and the following commands are handled correctly should be enough." The only libata user that actually cares about the result from a suspend operation is libsas. However, it only cares about whether queuing a new operation collides with an in-flight one. All libsas does with the error is retry, but we can just let libata wait for the previous operation before continuing. Other cleanups include: 1/ Unifying all ata port pm operations on an ata_port_pm_ prefix 2/ Marking all ata port pm helper routines as returning void, only ata_port_pm_ entry points need to fake a 0 return value. 3/ Killing ata_port_{suspend|resume}_common() in favor of calling ata_port_request_pm() directly 4/ Killing the wrappers that just do a to_ata_port() conversion 5/ Clearly marking the entry points that do async operations with an _async suffix. Reference: http://marc.info/?l=linux-scsi&m=138995409532286&w=2 Cc: Phillip Susi <psusi@ubuntu.com> Cc: Alan Stern <stern@rowland.harvard.edu> Suggested-by: Tejun Heo <tj@kernel.org> Signed-off-by: Todd Brandt <todd.e.brandt@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org>
2014-03-15 03:52:48 +07:00
static inline void ata_sas_port_suspend(struct ata_port *ap)
{
}
static inline void ata_sas_port_resume(struct ata_port *ap)
{
}
#endif
extern int ata_ratelimit(void);
extern void ata_msleep(struct ata_port *ap, unsigned int msecs);
extern u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask,
u32 val, unsigned long interval, unsigned long timeout);
extern int atapi_cmd_type(u8 opcode);
extern void ata_tf_to_fis(const struct ata_taskfile *tf,
u8 pmp, int is_cmd, u8 *fis);
extern void ata_tf_from_fis(const u8 *fis, struct ata_taskfile *tf);
extern unsigned long ata_pack_xfermask(unsigned long pio_mask,
unsigned long mwdma_mask, unsigned long udma_mask);
extern void ata_unpack_xfermask(unsigned long xfer_mask,
unsigned long *pio_mask, unsigned long *mwdma_mask,
unsigned long *udma_mask);
extern u8 ata_xfer_mask2mode(unsigned long xfer_mask);
extern unsigned long ata_xfer_mode2mask(u8 xfer_mode);
extern int ata_xfer_mode2shift(unsigned long xfer_mode);
extern const char *ata_mode_string(unsigned long xfer_mask);
extern unsigned long ata_id_xfermask(const u16 *id);
extern int ata_std_qc_defer(struct ata_queued_cmd *qc);
extern void ata_noop_qc_prep(struct ata_queued_cmd *qc);
extern void ata_sg_init(struct ata_queued_cmd *qc, struct scatterlist *sg,
unsigned int n_elem);
extern unsigned int ata_dev_classify(const struct ata_taskfile *tf);
extern void ata_dev_disable(struct ata_device *adev);
extern void ata_id_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
extern void ata_id_c_string(const u16 *id, unsigned char *s,
unsigned int ofs, unsigned int len);
extern unsigned int ata_do_dev_read_id(struct ata_device *dev,
struct ata_taskfile *tf, u16 *id);
extern void ata_qc_complete(struct ata_queued_cmd *qc);
extern int ata_qc_complete_multiple(struct ata_port *ap, u32 qc_active);
extern void ata_scsi_simulate(struct ata_device *dev, struct scsi_cmnd *cmd);
extern int ata_std_bios_param(struct scsi_device *sdev,
struct block_device *bdev,
sector_t capacity, int geom[]);
extern void ata_scsi_unlock_native_capacity(struct scsi_device *sdev);
extern int ata_scsi_slave_config(struct scsi_device *sdev);
extern void ata_scsi_slave_destroy(struct scsi_device *sdev);
extern int ata_scsi_change_queue_depth(struct scsi_device *sdev,
int queue_depth);
extern int __ata_change_queue_depth(struct ata_port *ap, struct scsi_device *sdev,
int queue_depth);
extern struct ata_device *ata_dev_pair(struct ata_device *adev);
extern int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
extern void ata_scsi_port_error_handler(struct Scsi_Host *host, struct ata_port *ap);
extern void ata_scsi_cmd_error_handler(struct Scsi_Host *host, struct ata_port *ap, struct list_head *eh_q);
extern bool sata_lpm_ignore_phy_events(struct ata_link *link);
extern int ata_cable_40wire(struct ata_port *ap);
extern int ata_cable_80wire(struct ata_port *ap);
extern int ata_cable_sata(struct ata_port *ap);
extern int ata_cable_ignore(struct ata_port *ap);
extern int ata_cable_unknown(struct ata_port *ap);
/* Timing helpers */
extern unsigned int ata_pio_need_iordy(const struct ata_device *);
extern const struct ata_timing *ata_timing_find_mode(u8 xfer_mode);
extern int ata_timing_compute(struct ata_device *, unsigned short,
struct ata_timing *, int, int);
extern void ata_timing_merge(const struct ata_timing *,
const struct ata_timing *, struct ata_timing *,
unsigned int);
extern u8 ata_timing_cycle2mode(unsigned int xfer_shift, int cycle);
/* PCI */
#ifdef CONFIG_PCI
struct pci_dev;
struct pci_bits {
unsigned int reg; /* PCI config register to read */
unsigned int width; /* 1 (8 bit), 2 (16 bit), 4 (32 bit) */
unsigned long mask;
unsigned long val;
};
extern int pci_test_config_bits(struct pci_dev *pdev, const struct pci_bits *bits);
extern void ata_pci_remove_one(struct pci_dev *pdev);
#ifdef CONFIG_PM
extern void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg);
extern int __must_check ata_pci_device_do_resume(struct pci_dev *pdev);
extern int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
extern int ata_pci_device_resume(struct pci_dev *pdev);
#endif /* CONFIG_PM */
#endif /* CONFIG_PCI */
struct platform_device;
extern int ata_platform_remove_one(struct platform_device *pdev);
/*
* ACPI - drivers/ata/libata-acpi.c
*/
#ifdef CONFIG_ATA_ACPI
static inline const struct ata_acpi_gtm *ata_acpi_init_gtm(struct ata_port *ap)
{
if (ap->pflags & ATA_PFLAG_INIT_GTM_VALID)
return &ap->__acpi_init_gtm;
return NULL;
}
int ata_acpi_stm(struct ata_port *ap, const struct ata_acpi_gtm *stm);
int ata_acpi_gtm(struct ata_port *ap, struct ata_acpi_gtm *stm);
unsigned long ata_acpi_gtm_xfermask(struct ata_device *dev,
const struct ata_acpi_gtm *gtm);
int ata_acpi_cbl_80wire(struct ata_port *ap, const struct ata_acpi_gtm *gtm);
#else
static inline const struct ata_acpi_gtm *ata_acpi_init_gtm(struct ata_port *ap)
{
return NULL;
}
static inline int ata_acpi_stm(const struct ata_port *ap,
struct ata_acpi_gtm *stm)
{
return -ENOSYS;
}
static inline int ata_acpi_gtm(const struct ata_port *ap,
struct ata_acpi_gtm *stm)
{
return -ENOSYS;
}
static inline unsigned int ata_acpi_gtm_xfermask(struct ata_device *dev,
const struct ata_acpi_gtm *gtm)
{
return 0;
}
static inline int ata_acpi_cbl_80wire(struct ata_port *ap,
const struct ata_acpi_gtm *gtm)
{
return 0;
}
#endif
/*
* EH - drivers/ata/libata-eh.c
*/
extern void ata_port_schedule_eh(struct ata_port *ap);
extern void ata_port_wait_eh(struct ata_port *ap);
extern int ata_link_abort(struct ata_link *link);
extern int ata_port_abort(struct ata_port *ap);
extern int ata_port_freeze(struct ata_port *ap);
extern int sata_async_notification(struct ata_port *ap);
extern void ata_eh_freeze_port(struct ata_port *ap);
extern void ata_eh_thaw_port(struct ata_port *ap);
extern void ata_eh_qc_complete(struct ata_queued_cmd *qc);
extern void ata_eh_qc_retry(struct ata_queued_cmd *qc);
extern void ata_eh_analyze_ncq_error(struct ata_link *link);
[PATCH] libata-hp-prep: add prereset() method and implement ata_std_prereset() With hotplug, every reset might be a probing reset and thus something similar to probe_init() is needed. prereset() method is called before a series of resets to a port and is the counterpart of postreset(). prereset() can tell EH to use different type of reset or skip reset by modifying ehc->i.action. This patch also implements ata_std_prereset(). Most controllers should be able to use this function directly or with some wrapping. After hotplug, different controllers need different actions to resume the PHY and detect the newly attached device. Controllers can be categorized as follows. * Controllers which can wait for the first D2H FIS after hotplug. Note that if the waiting is implemented by polling TF status, there needs to be a way to set BSY on PHY status change. It can be implemented by hardware or with the help of the driver. * Controllers which can wait for the first D2H FIS after sending COMRESET. These controllers need to issue COMRESET to wait for the first FIS. Note that the received D2H FIS could be the first D2H FIS after POR (power-on-reset) or D2H FIS in response to the COMRESET. Some controllers use COMRESET as TF status synchronization point and clear TF automatically (sata_sil). * Controllers which cannot wait for the first D2H FIS reliably. Blindly issuing SRST to spinning-up device often results in command issue failure or timeout, causing extended delay. For these controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT (currently 8s) to give newly attached device time to spin up, then issues reset. Note that failing to getting ready in ATA_SPINUP_WAIT is not critical. libata will retry. So, the timeout needs to be long enough to spin up most devices. LLDDs can tell ata_std_prereset() which of above action is needed with ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags. These flags are PHY-specific property and will be moved to ata_link later. While at it, this patch unifies function typedef's such that they all have named arguments. Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-05-31 16:27:48 +07:00
extern void ata_do_eh(struct ata_port *ap, ata_prereset_fn_t prereset,
ata_reset_fn_t softreset, ata_reset_fn_t hardreset,
ata_postreset_fn_t postreset);
libata: make reset related methods proper port operations Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 10:22:50 +07:00
extern void ata_std_error_handler(struct ata_port *ap);
extern void ata_std_sched_eh(struct ata_port *ap);
extern void ata_std_end_eh(struct ata_port *ap);
extern int ata_link_nr_enabled(struct ata_link *link);
/*
* Base operations to inherit from and initializers for sht
*
* Operations
*
* base : Common to all libata drivers.
* sata : SATA controllers w/ native interface.
* pmp : SATA controllers w/ PMP support.
* sff : SFF ATA controllers w/o BMDMA support.
* bmdma : SFF ATA controllers w/ BMDMA support.
*
* sht initializers
*
* BASE : Common to all libata drivers. The user must set
* sg_tablesize and dma_boundary.
* PIO : SFF ATA controllers w/ only PIO support.
* BMDMA : SFF ATA controllers w/ BMDMA support. sg_tablesize and
* dma_boundary are set to BMDMA limits.
* NCQ : SATA controllers supporting NCQ. The user must set
* sg_tablesize, dma_boundary and can_queue.
*/
extern const struct ata_port_operations ata_base_port_ops;
extern const struct ata_port_operations sata_port_ops;
extern struct device_attribute *ata_common_sdev_attrs[];
/*
* All sht initializers (BASE, PIO, BMDMA, NCQ) must be instantiated
* by the edge drivers. Because the 'module' field of sht must be the
* edge driver's module reference, otherwise the driver can be unloaded
* even if the scsi_device is being accessed.
*/
#define ATA_BASE_SHT(drv_name) \
.module = THIS_MODULE, \
.name = drv_name, \
.ioctl = ata_scsi_ioctl, \
.queuecommand = ata_scsi_queuecmd, \
.can_queue = ATA_DEF_QUEUE, \
.tag_alloc_policy = BLK_TAG_ALLOC_RR, \
.this_id = ATA_SHT_THIS_ID, \
.emulated = ATA_SHT_EMULATED, \
.use_clustering = ATA_SHT_USE_CLUSTERING, \
.proc_name = drv_name, \
.slave_configure = ata_scsi_slave_config, \
.slave_destroy = ata_scsi_slave_destroy, \
.eh_timed_out = ata_scsi_timed_out, \
.bios_param = ata_std_bios_param, \
.unlock_native_capacity = ata_scsi_unlock_native_capacity, \
.sdev_attrs = ata_common_sdev_attrs
#define ATA_NCQ_SHT(drv_name) \
ATA_BASE_SHT(drv_name), \
.change_queue_depth = ata_scsi_change_queue_depth
/*
* PMP helpers
*/
#ifdef CONFIG_SATA_PMP
static inline bool sata_pmp_supported(struct ata_port *ap)
{
return ap->flags & ATA_FLAG_PMP;
}
static inline bool sata_pmp_attached(struct ata_port *ap)
{
return ap->nr_pmp_links != 0;
}
static inline bool ata_is_host_link(const struct ata_link *link)
{
libata: implement slave_link Explanation taken from the comment of ata_slave_link_init(). In libata, a port contains links and a link contains devices. There is single host link but if a PMP is attached to it, there can be multiple fan-out links. On SATA, there's usually a single device connected to a link but PATA and SATA controllers emulating TF based interface can have two - master and slave. However, there are a few controllers which don't fit into this abstraction too well - SATA controllers which emulate TF interface with both master and slave devices but also have separate SCR register sets for each device. These controllers need separate links for physical link handling (e.g. onlineness, link speed) but should be treated like a traditional M/S controller for everything else (e.g. command issue, softreset). slave_link is libata's way of handling this class of controllers without impacting core layer too much. For anything other than physical link handling, the default host link is used for both master and slave. For physical link handling, separate @ap->slave_link is used. All dirty details are implemented inside libata core layer. From LLD's POV, the only difference is that prereset, hardreset and postreset are called once more for the slave link, so the reset sequence looks like the following. prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) -> softreset(M) -> postreset(M) -> postreset(S) Note that softreset is called only for the master. Softreset resets both M/S by definition, so SRST on master should handle both (the standard method will work just fine). As slave_link excludes PMP support and only code paths which deal with the attributes of physical link are affected, all the changes are localized to libata.h, libata-core.c and libata-eh.c. * ata_is_host_link() updated so that slave_link is considered as host link too. * iterator extended to iterate over the slave_link when using the underbarred version. * force param handling updated such that devno 16 is mapped to the slave link/device. * ata_link_on/offline() updated to return the combined result from master and slave link. ata_phys_link_on/offline() are the direct versions. * EH autopsy and report are performed separately for master slave links. Reset is udpated to implement the above described reset sequence. Except for reset update, most changes are minor, many of them just modifying dev->link to ata_dev_phys_link(dev) or using phys online test instead. After this update, LLDs can take full advantage of per-dev SCR registers by simply turning on slave link. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 15:02:43 +07:00
return link == &link->ap->link || link == link->ap->slave_link;
}
#else /* CONFIG_SATA_PMP */
static inline bool sata_pmp_supported(struct ata_port *ap)
{
return false;
}
static inline bool sata_pmp_attached(struct ata_port *ap)
{
return false;
}
static inline bool ata_is_host_link(const struct ata_link *link)
{
return 1;
}
#endif /* CONFIG_SATA_PMP */
static inline int sata_srst_pmp(struct ata_link *link)
{
if (sata_pmp_supported(link->ap) && ata_is_host_link(link))
return SATA_PMP_CTRL_PORT;
return link->pmp;
}
/*
* printk helpers
*/
__printf(3, 4)
void ata_port_printk(const struct ata_port *ap, const char *level,
const char *fmt, ...);
__printf(3, 4)
void ata_link_printk(const struct ata_link *link, const char *level,
const char *fmt, ...);
__printf(3, 4)
void ata_dev_printk(const struct ata_device *dev, const char *level,
const char *fmt, ...);
#define ata_port_err(ap, fmt, ...) \
ata_port_printk(ap, KERN_ERR, fmt, ##__VA_ARGS__)
#define ata_port_warn(ap, fmt, ...) \
ata_port_printk(ap, KERN_WARNING, fmt, ##__VA_ARGS__)
#define ata_port_notice(ap, fmt, ...) \
ata_port_printk(ap, KERN_NOTICE, fmt, ##__VA_ARGS__)
#define ata_port_info(ap, fmt, ...) \
ata_port_printk(ap, KERN_INFO, fmt, ##__VA_ARGS__)
#define ata_port_dbg(ap, fmt, ...) \
ata_port_printk(ap, KERN_DEBUG, fmt, ##__VA_ARGS__)
#define ata_link_err(link, fmt, ...) \
ata_link_printk(link, KERN_ERR, fmt, ##__VA_ARGS__)
#define ata_link_warn(link, fmt, ...) \
ata_link_printk(link, KERN_WARNING, fmt, ##__VA_ARGS__)
#define ata_link_notice(link, fmt, ...) \
ata_link_printk(link, KERN_NOTICE, fmt, ##__VA_ARGS__)
#define ata_link_info(link, fmt, ...) \
ata_link_printk(link, KERN_INFO, fmt, ##__VA_ARGS__)
#define ata_link_dbg(link, fmt, ...) \
ata_link_printk(link, KERN_DEBUG, fmt, ##__VA_ARGS__)
#define ata_dev_err(dev, fmt, ...) \
ata_dev_printk(dev, KERN_ERR, fmt, ##__VA_ARGS__)
#define ata_dev_warn(dev, fmt, ...) \
ata_dev_printk(dev, KERN_WARNING, fmt, ##__VA_ARGS__)
#define ata_dev_notice(dev, fmt, ...) \
ata_dev_printk(dev, KERN_NOTICE, fmt, ##__VA_ARGS__)
#define ata_dev_info(dev, fmt, ...) \
ata_dev_printk(dev, KERN_INFO, fmt, ##__VA_ARGS__)
#define ata_dev_dbg(dev, fmt, ...) \
ata_dev_printk(dev, KERN_DEBUG, fmt, ##__VA_ARGS__)
void ata_print_version(const struct device *dev, const char *version);
/*
* ata_eh_info helpers
*/
extern __printf(2, 3)
void __ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...);
extern __printf(2, 3)
void ata_ehi_push_desc(struct ata_eh_info *ehi, const char *fmt, ...);
extern void ata_ehi_clear_desc(struct ata_eh_info *ehi);
static inline void ata_ehi_hotplugged(struct ata_eh_info *ehi)
{
ehi->probe_mask |= (1 << ATA_MAX_DEVICES) - 1;
ehi->flags |= ATA_EHI_HOTPLUGGED;
ehi->action |= ATA_EH_RESET | ATA_EH_ENABLE_LINK;
ehi->err_mask |= AC_ERR_ATA_BUS;
}
/*
* port description helpers
*/
extern __printf(2, 3)
void ata_port_desc(struct ata_port *ap, const char *fmt, ...);
#ifdef CONFIG_PCI
extern void ata_port_pbar_desc(struct ata_port *ap, int bar, ssize_t offset,
const char *name);
#endif
static inline unsigned int ata_tag_valid(unsigned int tag)
{
return (tag < ATA_MAX_QUEUE) ? 1 : 0;
}
static inline unsigned int ata_tag_internal(unsigned int tag)
{
return tag == ATA_TAG_INTERNAL;
}
/*
* device helpers
*/
static inline unsigned int ata_class_enabled(unsigned int class)
{
return class == ATA_DEV_ATA || class == ATA_DEV_ATAPI ||
class == ATA_DEV_PMP || class == ATA_DEV_SEMB ||
class == ATA_DEV_ZAC;
}
static inline unsigned int ata_class_disabled(unsigned int class)
{
return class == ATA_DEV_ATA_UNSUP || class == ATA_DEV_ATAPI_UNSUP ||
class == ATA_DEV_PMP_UNSUP || class == ATA_DEV_SEMB_UNSUP ||
class == ATA_DEV_ZAC_UNSUP;
}
static inline unsigned int ata_class_absent(unsigned int class)
{
return !ata_class_enabled(class) && !ata_class_disabled(class);
}
static inline unsigned int ata_dev_enabled(const struct ata_device *dev)
{
return ata_class_enabled(dev->class);
}
static inline unsigned int ata_dev_disabled(const struct ata_device *dev)
{
return ata_class_disabled(dev->class);
}
static inline unsigned int ata_dev_absent(const struct ata_device *dev)
{
return ata_class_absent(dev->class);
}
/*
* link helpers
*/
static inline int ata_link_max_devices(const struct ata_link *link)
{
if (ata_is_host_link(link) && link->ap->flags & ATA_FLAG_SLAVE_POSS)
return 2;
return 1;
}
static inline int ata_link_active(struct ata_link *link)
{
return ata_tag_valid(link->active_tag) || link->sactive;
}
/*
* Iterators
*
* ATA_LITER_* constants are used to select link iteration mode and
* ATA_DITER_* device iteration mode.
*
* For a custom iteration directly using ata_{link|dev}_next(), if
* @link or @dev, respectively, is NULL, the first element is
* returned. @dev and @link can be any valid device or link and the
* next element according to the iteration mode will be returned.
* After the last element, NULL is returned.
*/
enum ata_link_iter_mode {
ATA_LITER_EDGE, /* if present, PMP links only; otherwise,
* host link. no slave link */
ATA_LITER_HOST_FIRST, /* host link followed by PMP or slave links */
ATA_LITER_PMP_FIRST, /* PMP links followed by host link,
* slave link still comes after host link */
};
enum ata_dev_iter_mode {
ATA_DITER_ENABLED,
ATA_DITER_ENABLED_REVERSE,
ATA_DITER_ALL,
ATA_DITER_ALL_REVERSE,
};
extern struct ata_link *ata_link_next(struct ata_link *link,
struct ata_port *ap,
enum ata_link_iter_mode mode);
extern struct ata_device *ata_dev_next(struct ata_device *dev,
struct ata_link *link,
enum ata_dev_iter_mode mode);
/*
* Shortcut notation for iterations
*
* ata_for_each_link() iterates over each link of @ap according to
* @mode. @link points to the current link in the loop. @link is
* NULL after loop termination. ata_for_each_dev() works the same way
* except that it iterates over each device of @link.
*
* Note that the mode prefixes ATA_{L|D}ITER_ shouldn't need to be
* specified when using the following shorthand notations. Only the
* mode itself (EDGE, HOST_FIRST, ENABLED, etc...) should be
* specified. This not only increases brevity but also makes it
* impossible to use ATA_LITER_* for device iteration or vice-versa.
*/
#define ata_for_each_link(link, ap, mode) \
for ((link) = ata_link_next(NULL, (ap), ATA_LITER_##mode); (link); \
(link) = ata_link_next((link), (ap), ATA_LITER_##mode))
#define ata_for_each_dev(dev, link, mode) \
for ((dev) = ata_dev_next(NULL, (link), ATA_DITER_##mode); (dev); \
(dev) = ata_dev_next((dev), (link), ATA_DITER_##mode))
/**
* ata_ncq_enabled - Test whether NCQ is enabled
* @dev: ATA device to test for
*
* LOCKING:
* spin_lock_irqsave(host lock)
*
* RETURNS:
* 1 if NCQ is enabled for @dev, 0 otherwise.
*/
static inline int ata_ncq_enabled(struct ata_device *dev)
{
return (dev->flags & (ATA_DFLAG_PIO | ATA_DFLAG_NCQ_OFF |
ATA_DFLAG_NCQ)) == ATA_DFLAG_NCQ;
}
2005-06-03 05:17:13 +07:00
static inline bool ata_fpdma_dsm_supported(struct ata_device *dev)
{
return (dev->flags & ATA_DFLAG_NCQ_SEND_RECV) &&
(dev->ncq_send_recv_cmds[ATA_LOG_NCQ_SEND_RECV_DSM_OFFSET] &
ATA_LOG_NCQ_SEND_RECV_DSM_TRIM);
}
static inline bool ata_fpdma_read_log_supported(struct ata_device *dev)
{
return (dev->flags & ATA_DFLAG_NCQ_SEND_RECV) &&
(dev->ncq_send_recv_cmds[ATA_LOG_NCQ_SEND_RECV_RD_LOG_OFFSET] &
ATA_LOG_NCQ_SEND_RECV_RD_LOG_SUPPORTED);
}
static inline bool ata_fpdma_zac_mgmt_in_supported(struct ata_device *dev)
{
return (dev->flags & ATA_DFLAG_NCQ_SEND_RECV) &&
(dev->ncq_send_recv_cmds[ATA_LOG_NCQ_SEND_RECV_ZAC_MGMT_OFFSET] &
ATA_LOG_NCQ_SEND_RECV_ZAC_MGMT_IN_SUPPORTED);
}
static inline bool ata_fpdma_zac_mgmt_out_supported(struct ata_device *dev)
{
return (dev->ncq_non_data_cmds[ATA_LOG_NCQ_NON_DATA_ZAC_MGMT_OFFSET] &
ATA_LOG_NCQ_NON_DATA_ZAC_MGMT_OUT);
}
static inline void ata_qc_set_polling(struct ata_queued_cmd *qc)
{
qc->tf.ctl |= ATA_NIEN;
}
static inline struct ata_queued_cmd *__ata_qc_from_tag(struct ata_port *ap,
unsigned int tag)
{
if (likely(ata_tag_valid(tag)))
return &ap->qcmd[tag];
return NULL;
}
static inline struct ata_queued_cmd *ata_qc_from_tag(struct ata_port *ap,
unsigned int tag)
{
struct ata_queued_cmd *qc = __ata_qc_from_tag(ap, tag);
if (unlikely(!qc) || !ap->ops->error_handler)
return qc;
if ((qc->flags & (ATA_QCFLAG_ACTIVE |
ATA_QCFLAG_FAILED)) == ATA_QCFLAG_ACTIVE)
return qc;
return NULL;
}
static inline unsigned int ata_qc_raw_nbytes(struct ata_queued_cmd *qc)
{
return qc->nbytes - min(qc->extrabytes, qc->nbytes);
}
static inline void ata_tf_init(struct ata_device *dev, struct ata_taskfile *tf)
{
memset(tf, 0, sizeof(*tf));
#ifdef CONFIG_ATA_SFF
tf->ctl = dev->link->ap->ctl;
#else
tf->ctl = ATA_DEVCTL_OBS;
#endif
if (dev->devno == 0)
tf->device = ATA_DEVICE_OBS;
else
tf->device = ATA_DEVICE_OBS | ATA_DEV1;
}
static inline void ata_qc_reinit(struct ata_queued_cmd *qc)
{
qc->dma_dir = DMA_NONE;
qc->sg = NULL;
qc->flags = 0;
qc->cursg = NULL;
qc->cursg_ofs = 0;
qc->nbytes = qc->extrabytes = qc->curbytes = 0;
qc->n_elem = 0;
qc->err_mask = 0;
qc->sect_size = ATA_SECT_SIZE;
ata_tf_init(qc->dev, &qc->tf);
/* init result_tf such that it indicates normal completion */
qc->result_tf.command = ATA_DRDY;
qc->result_tf.feature = 0;
}
static inline int ata_try_flush_cache(const struct ata_device *dev)
{
return ata_id_wcache_enabled(dev->id) ||
ata_id_has_flush(dev->id) ||
ata_id_has_flush_ext(dev->id);
}
static inline unsigned int ac_err_mask(u8 status)
{
if (status & (ATA_BUSY | ATA_DRQ))
return AC_ERR_HSM;
if (status & (ATA_ERR | ATA_DF))
return AC_ERR_DEV;
return 0;
}
static inline unsigned int __ac_err_mask(u8 status)
{
unsigned int mask = ac_err_mask(status);
if (mask == 0)
return AC_ERR_OTHER;
return mask;
}
2006-04-12 00:12:34 +07:00
static inline struct ata_port *ata_shost_to_port(struct Scsi_Host *host)
{
return *(struct ata_port **)&host->hostdata[0];
2006-04-12 00:12:34 +07:00
}
static inline int ata_check_ready(u8 status)
{
if (!(status & ATA_BUSY))
return 1;
/* 0xff indicates either no device or device not ready */
if (status == 0xff)
return -ENODEV;
return 0;
}
static inline unsigned long ata_deadline(unsigned long from_jiffies,
unsigned long timeout_msecs)
{
return from_jiffies + msecs_to_jiffies(timeout_msecs);
}
/* Don't open code these in drivers as there are traps. Firstly the range may
change in future hardware and specs, secondly 0xFF means 'no DMA' but is
> UDMA_0. Dyma ddreigiau */
static inline int ata_using_mwdma(struct ata_device *adev)
{
if (adev->dma_mode >= XFER_MW_DMA_0 && adev->dma_mode <= XFER_MW_DMA_4)
return 1;
return 0;
}
static inline int ata_using_udma(struct ata_device *adev)
{
if (adev->dma_mode >= XFER_UDMA_0 && adev->dma_mode <= XFER_UDMA_7)
return 1;
return 0;
}
static inline int ata_dma_enabled(struct ata_device *adev)
{
return (adev->dma_mode == 0xFF ? 0 : 1);
}
/**************************************************************************
* PMP - drivers/ata/libata-pmp.c
*/
#ifdef CONFIG_SATA_PMP
extern const struct ata_port_operations sata_pmp_port_ops;
extern int sata_pmp_qc_defer_cmd_switch(struct ata_queued_cmd *qc);
extern void sata_pmp_error_handler(struct ata_port *ap);
#else /* CONFIG_SATA_PMP */
#define sata_pmp_port_ops sata_port_ops
#define sata_pmp_qc_defer_cmd_switch ata_std_qc_defer
#define sata_pmp_error_handler ata_std_error_handler
#endif /* CONFIG_SATA_PMP */
/**************************************************************************
* SFF - drivers/ata/libata-sff.c
*/
#ifdef CONFIG_ATA_SFF
extern const struct ata_port_operations ata_sff_port_ops;
extern const struct ata_port_operations ata_bmdma32_port_ops;
/* PIO only, sg_tablesize and dma_boundary limits can be removed */
#define ATA_PIO_SHT(drv_name) \
ATA_BASE_SHT(drv_name), \
.sg_tablesize = LIBATA_MAX_PRD, \
.dma_boundary = ATA_DMA_BOUNDARY
extern void ata_sff_dev_select(struct ata_port *ap, unsigned int device);
extern u8 ata_sff_check_status(struct ata_port *ap);
extern void ata_sff_pause(struct ata_port *ap);
extern void ata_sff_dma_pause(struct ata_port *ap);
extern int ata_sff_busy_sleep(struct ata_port *ap,
unsigned long timeout_pat, unsigned long timeout);
libata: restructure SFF post-reset readiness waits Previously, post-softreset readiness is waited as follows. 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff. If not, continue to #3. 3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending on devmask using ata_sff_wait_ready(). And for post-hardreset readiness, 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. sata_sff_hardreset waits for device readiness using ata_sff_wait_ready(). This patch merges and unifies post-reset readiness waits into ata_sff_wait_ready() and ata_sff_wait_after_reset(). ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF status is 0xff, link status is unknown and the port is SATA, it will continue polling till ATA_TMOUT_FF_WAIT. ata_sff_wait_after_reset() is updated to perform the following steps. 1. waits for 150ms. 2. waits for dev0 readiness using ata_sff_wait_ready(). Note that this is done regardless of devmask, as ata_sff_wait_ready() handles 0xff status correctly, this preserves the original behavior except that it may wait longer after softreset if link is online but status is 0xff. This behavior change is very unlikely to cause any actual difference and is intended. It brings softreset behavior to that of hardreset. 3. waits for dev1 readiness just the same way ata_bus_post_reset() did. Now both soft and hard resets call ata_sff_wait_after_reset() after reset to wait for readiness after resets. As ata_sff_wait_after_reset() contains calls to ->sff_dev_select(), explicit call near the end of sata_sff_hardreset() is removed. This change makes reset implementation simpler and more consistent. While at it, make the magical 150ms wait post-reset wait duration a constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take @link instead of @ap. This is to make them consistent with other reset helpers and ease core changes. pata_scc is updated accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-07 20:47:19 +07:00
extern int ata_sff_wait_ready(struct ata_link *link, unsigned long deadline);
extern void ata_sff_tf_load(struct ata_port *ap, const struct ata_taskfile *tf);
extern void ata_sff_tf_read(struct ata_port *ap, struct ata_taskfile *tf);
extern void ata_sff_exec_command(struct ata_port *ap,
const struct ata_taskfile *tf);
extern unsigned int ata_sff_data_xfer(struct ata_queued_cmd *qc,
unsigned char *buf, unsigned int buflen, int rw);
extern unsigned int ata_sff_data_xfer32(struct ata_queued_cmd *qc,
unsigned char *buf, unsigned int buflen, int rw);
extern unsigned int ata_sff_data_xfer_noirq(struct ata_queued_cmd *qc,
unsigned char *buf, unsigned int buflen, int rw);
extern void ata_sff_irq_on(struct ata_port *ap);
extern void ata_sff_irq_clear(struct ata_port *ap);
extern int ata_sff_hsm_move(struct ata_port *ap, struct ata_queued_cmd *qc,
u8 status, int in_wq);
extern void ata_sff_queue_work(struct work_struct *work);
extern void ata_sff_queue_delayed_work(struct delayed_work *dwork,
unsigned long delay);
extern void ata_sff_queue_pio_task(struct ata_link *link, unsigned long delay);
extern unsigned int ata_sff_qc_issue(struct ata_queued_cmd *qc);
extern bool ata_sff_qc_fill_rtf(struct ata_queued_cmd *qc);
extern unsigned int ata_sff_port_intr(struct ata_port *ap,
struct ata_queued_cmd *qc);
extern irqreturn_t ata_sff_interrupt(int irq, void *dev_instance);
extern void ata_sff_lost_interrupt(struct ata_port *ap);
extern void ata_sff_freeze(struct ata_port *ap);
extern void ata_sff_thaw(struct ata_port *ap);
extern int ata_sff_prereset(struct ata_link *link, unsigned long deadline);
extern unsigned int ata_sff_dev_classify(struct ata_device *dev, int present,
u8 *r_err);
libata: restructure SFF post-reset readiness waits Previously, post-softreset readiness is waited as follows. 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff. If not, continue to #3. 3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending on devmask using ata_sff_wait_ready(). And for post-hardreset readiness, 1. ata_sff_wait_after_reset() waits for 150ms and then for ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet. 2. sata_sff_hardreset waits for device readiness using ata_sff_wait_ready(). This patch merges and unifies post-reset readiness waits into ata_sff_wait_ready() and ata_sff_wait_after_reset(). ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF status is 0xff, link status is unknown and the port is SATA, it will continue polling till ATA_TMOUT_FF_WAIT. ata_sff_wait_after_reset() is updated to perform the following steps. 1. waits for 150ms. 2. waits for dev0 readiness using ata_sff_wait_ready(). Note that this is done regardless of devmask, as ata_sff_wait_ready() handles 0xff status correctly, this preserves the original behavior except that it may wait longer after softreset if link is online but status is 0xff. This behavior change is very unlikely to cause any actual difference and is intended. It brings softreset behavior to that of hardreset. 3. waits for dev1 readiness just the same way ata_bus_post_reset() did. Now both soft and hard resets call ata_sff_wait_after_reset() after reset to wait for readiness after resets. As ata_sff_wait_after_reset() contains calls to ->sff_dev_select(), explicit call near the end of sata_sff_hardreset() is removed. This change makes reset implementation simpler and more consistent. While at it, make the magical 150ms wait post-reset wait duration a constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take @link instead of @ap. This is to make them consistent with other reset helpers and ease core changes. pata_scc is updated accordingly. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-07 20:47:19 +07:00
extern int ata_sff_wait_after_reset(struct ata_link *link, unsigned int devmask,
unsigned long deadline);
extern int ata_sff_softreset(struct ata_link *link, unsigned int *classes,
unsigned long deadline);
extern int sata_sff_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
extern void ata_sff_postreset(struct ata_link *link, unsigned int *classes);
extern void ata_sff_drain_fifo(struct ata_queued_cmd *qc);
extern void ata_sff_error_handler(struct ata_port *ap);
extern void ata_sff_std_ports(struct ata_ioports *ioaddr);
#ifdef CONFIG_PCI
extern int ata_pci_sff_init_host(struct ata_host *host);
extern int ata_pci_sff_prepare_host(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
struct ata_host **r_host);
extern int ata_pci_sff_activate_host(struct ata_host *host,
irq_handler_t irq_handler,
struct scsi_host_template *sht);
extern int ata_pci_sff_init_one(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
struct scsi_host_template *sht, void *host_priv, int hflags);
#endif /* CONFIG_PCI */
#ifdef CONFIG_ATA_BMDMA
extern const struct ata_port_operations ata_bmdma_port_ops;
#define ATA_BMDMA_SHT(drv_name) \
ATA_BASE_SHT(drv_name), \
.sg_tablesize = LIBATA_MAX_PRD, \
.dma_boundary = ATA_DMA_BOUNDARY
extern void ata_bmdma_qc_prep(struct ata_queued_cmd *qc);
extern unsigned int ata_bmdma_qc_issue(struct ata_queued_cmd *qc);
extern void ata_bmdma_dumb_qc_prep(struct ata_queued_cmd *qc);
extern unsigned int ata_bmdma_port_intr(struct ata_port *ap,
struct ata_queued_cmd *qc);
extern irqreturn_t ata_bmdma_interrupt(int irq, void *dev_instance);
extern void ata_bmdma_error_handler(struct ata_port *ap);
extern void ata_bmdma_post_internal_cmd(struct ata_queued_cmd *qc);
extern void ata_bmdma_irq_clear(struct ata_port *ap);
extern void ata_bmdma_setup(struct ata_queued_cmd *qc);
extern void ata_bmdma_start(struct ata_queued_cmd *qc);
extern void ata_bmdma_stop(struct ata_queued_cmd *qc);
extern u8 ata_bmdma_status(struct ata_port *ap);
libata-sff: clean up BMDMA initialization When BMDMA initialization failed or BMDMA was not available for whatever reason, bmdma_addr was left at zero and used as an indication that BMDMA shouldn't be used. This leads to the following problems. p1. For BMDMA drivers which don't use traditional BMDMA register, ata_bmdma_mode_filter() incorrectly inhibits DMA modes. Those drivers either have to inherit from ata_sff_port_ops or clear ->mode_filter explicitly. p2. non-BMDMA drivers call into BMDMA PRD table allocation. It doesn't actually allocate PRD table if bmdma_addr is not initialized but is still confusing. p3. For BMDMA drivers which don't use traditional BMDMA register, some methods might not be invoked as expected (e.g. bmdma_stop from ata_sff_post_internal_cmd()). p4. SFF drivers w/ custom DMA interface implement noop BMDMA ops worrying libata core might call into one of them. These problems are caused by the muddy line between SFF and BMDMA and the assumption that all BMDMA controllers initialize bmdma_addr. This patch fixes p1 and p2 by removing the bmdma_addr assumption and moving prd allocation to BMDMA port start. Later patches will fix the remaining issues. This patch improves BMDMA initialization such that * When BMDMA register initialization fails, falls back to PIO instead of failing. ata_pci_bmdma_init() never fails now. * When ata_pci_bmdma_init() falls back to PIO, it clears ap->mwdma_mask and udma_mask instead of depending on ata_bmdma_mode_filter(). This makes ata_bmdma_mode_filter() unnecessary thus resolving p1. * ata_port_start() which actually is BMDMA specific is moved to ata_bmdma_port_start(). ata_port_start() and ata_sff_port_start() are killed. * ata_sff_port_start32() is moved and renamed to ata_bmdma_port_start32(). Drivers which no longer call into PRD table allocation are... pdc_adma, sata_inic162x, sata_qstor, sata_sx4, pata_cmd640 and all drivers which inherit from ata_sff_port_ops. pata_icside sets ->port_start to ATA_OP_NULL as it doesn't need PRD but is a BMDMA controller and doesn't have custom port_start like other such controllers. Note that with the previous patch which makes all and only BMDMA drivers inherit from ata_bmdma_port_ops, this change doesn't break drivers which need PRD table. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-05-11 02:41:34 +07:00
extern int ata_bmdma_port_start(struct ata_port *ap);
extern int ata_bmdma_port_start32(struct ata_port *ap);
#ifdef CONFIG_PCI
extern int ata_pci_bmdma_clear_simplex(struct pci_dev *pdev);
libata-sff: clean up BMDMA initialization When BMDMA initialization failed or BMDMA was not available for whatever reason, bmdma_addr was left at zero and used as an indication that BMDMA shouldn't be used. This leads to the following problems. p1. For BMDMA drivers which don't use traditional BMDMA register, ata_bmdma_mode_filter() incorrectly inhibits DMA modes. Those drivers either have to inherit from ata_sff_port_ops or clear ->mode_filter explicitly. p2. non-BMDMA drivers call into BMDMA PRD table allocation. It doesn't actually allocate PRD table if bmdma_addr is not initialized but is still confusing. p3. For BMDMA drivers which don't use traditional BMDMA register, some methods might not be invoked as expected (e.g. bmdma_stop from ata_sff_post_internal_cmd()). p4. SFF drivers w/ custom DMA interface implement noop BMDMA ops worrying libata core might call into one of them. These problems are caused by the muddy line between SFF and BMDMA and the assumption that all BMDMA controllers initialize bmdma_addr. This patch fixes p1 and p2 by removing the bmdma_addr assumption and moving prd allocation to BMDMA port start. Later patches will fix the remaining issues. This patch improves BMDMA initialization such that * When BMDMA register initialization fails, falls back to PIO instead of failing. ata_pci_bmdma_init() never fails now. * When ata_pci_bmdma_init() falls back to PIO, it clears ap->mwdma_mask and udma_mask instead of depending on ata_bmdma_mode_filter(). This makes ata_bmdma_mode_filter() unnecessary thus resolving p1. * ata_port_start() which actually is BMDMA specific is moved to ata_bmdma_port_start(). ata_port_start() and ata_sff_port_start() are killed. * ata_sff_port_start32() is moved and renamed to ata_bmdma_port_start32(). Drivers which no longer call into PRD table allocation are... pdc_adma, sata_inic162x, sata_qstor, sata_sx4, pata_cmd640 and all drivers which inherit from ata_sff_port_ops. pata_icside sets ->port_start to ATA_OP_NULL as it doesn't need PRD but is a BMDMA controller and doesn't have custom port_start like other such controllers. Note that with the previous patch which makes all and only BMDMA drivers inherit from ata_bmdma_port_ops, this change doesn't break drivers which need PRD table. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-05-11 02:41:34 +07:00
extern void ata_pci_bmdma_init(struct ata_host *host);
extern int ata_pci_bmdma_prepare_host(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
struct ata_host **r_host);
extern int ata_pci_bmdma_init_one(struct pci_dev *pdev,
const struct ata_port_info * const * ppi,
struct scsi_host_template *sht,
void *host_priv, int hflags);
#endif /* CONFIG_PCI */
#endif /* CONFIG_ATA_BMDMA */
/**
* ata_sff_busy_wait - Wait for a port status register
* @ap: Port to wait for.
* @bits: bits that must be clear
* @max: number of 10uS waits to perform
*
* Waits up to max*10 microseconds for the selected bits in the port's
* status register to be cleared.
* Returns final value of status register.
*
* LOCKING:
* Inherited from caller.
*/
static inline u8 ata_sff_busy_wait(struct ata_port *ap, unsigned int bits,
unsigned int max)
{
u8 status;
do {
udelay(10);
status = ap->ops->sff_check_status(ap);
max--;
} while (status != 0xff && (status & bits) && (max > 0));
return status;
}
/**
* ata_wait_idle - Wait for a port to be idle.
* @ap: Port to wait for.
*
* Waits up to 10ms for port's BUSY and DRQ signals to clear.
* Returns final value of status register.
*
* LOCKING:
* Inherited from caller.
*/
static inline u8 ata_wait_idle(struct ata_port *ap)
{
u8 status = ata_sff_busy_wait(ap, ATA_BUSY | ATA_DRQ, 1000);
#ifdef ATA_DEBUG
if (status != 0xff && (status & (ATA_BUSY | ATA_DRQ)))
ata_port_printk(ap, KERN_DEBUG, "abnormal Status 0x%X\n",
status);
#endif
return status;
}
#endif /* CONFIG_ATA_SFF */
#endif /* __LINUX_LIBATA_H__ */