linux_dsm_epyc7002/arch/arm/boot/dts/bcm2835-rpi-b.dts

/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9512.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"

/ {
	compatible = "raspberrypi,model-b", "brcm,bcm2835";
	model = "Raspberry Pi Model B";

	leds {
		act {
			gpios = <&gpio 16 1>;
		};
	};
};

&gpio {
	pinctrl-0 = <&gpioout &alt0 &alt3>;
};

&hdmi {
	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
ARM: add infra-structure for BCM2835 and Raspberry Pi The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic support for this SoC. http://www.broadcom.com/products/BCM2835 http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Note that the documentation in the latter .pdf assumes the MMU setup that's used on the "VideoCore" companion processor, and does not document physical peripheral addresses. Subtract 0x5e000000 to obtain the physical addresses. This is accounted for by the ranges property in the /soc node in the device tree. The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a minimal device tree for this board; enough to see some very early kernel boot messages through earlyprintk. However, this patch does not yet provide a useful booting system. http://www.raspberrypi.org/. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split from 3-4 months ago, and significantly stripped down and modified since. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Dom Cobley <popcornmix@gmail.com> Signed-off-by: Dom Cobley <dc4@broadcom.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de> 2012-05-26 14:04:43 +07:00			`/dts-v1/;`
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT. For Raspberry Pi 2, we want to use the same general pin assignment bits, but need to use bcm2836.dtsi for the CPU instead. Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> 2015-12-17 06:55:12 +07:00			`#include "bcm2835.dtsi"`
ARM: bcm2835: dt: Use pinctrl header This patch converts all bcm2835 dts and dtsi files to use the pinctrl header file. Reviewed-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> 2015-01-30 01:10:50 +07:00			`#include "bcm2835-rpi.dtsi"`
ARM: bcm2835: dt: Add the ethernet to the device trees The hub and the ethernet in its port 1 are hardwired on the board. Compared to the adapters that can be plugged into the USB ports, this one has no serial EEPROM to store its MAC. Nevertheless, the Raspberry Pi has the MAC address for this adapter in its ROM, accessible from its firmware. U-Boot can read out the address and set the local-mac-address property of the node with "ethernet" alias. Let's add the node so that U-Boot can do its business. Model B rev2 and Model B+ entries were verified by me, the hierarchy and pid/vid pair for the Version 2 was provided by Peter Chen. Original Model B is a blind shot, though very likely correct. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Eric Anholt <eric@anholt.net> 2016-05-02 14:06:51 +07:00			`#include "bcm283x-rpi-smsc9512.dtsi"`
ARM: dts: bcm283x: Add dtsi for USB host mode In case dr_mode isn't passed via DT, the dwc2 defaults to OTG mode. But all Raspberry Pi boards here are designed only for host mode. So fix this issue by providing a dtsi file which set the dr_mode to host. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Eric Anholt <eric@anholt.net> 2016-08-21 22:10:00 +07:00			`#include "bcm283x-rpi-usb-host.dtsi"`
ARM: add infra-structure for BCM2835 and Raspberry Pi The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic support for this SoC. http://www.broadcom.com/products/BCM2835 http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Note that the documentation in the latter .pdf assumes the MMU setup that's used on the "VideoCore" companion processor, and does not document physical peripheral addresses. Subtract 0x5e000000 to obtain the physical addresses. This is accounted for by the ranges property in the /soc node in the device tree. The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a minimal device tree for this board; enough to see some very early kernel boot messages through earlyprintk. However, this patch does not yet provide a useful booting system. http://www.raspberrypi.org/. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split from 3-4 months ago, and significantly stripped down and modified since. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Dom Cobley <popcornmix@gmail.com> Signed-off-by: Dom Cobley <dc4@broadcom.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de> 2012-05-26 14:04:43 +07:00
			`/ {`
			`compatible = "raspberrypi,model-b", "brcm,bcm2835";`
			`model = "Raspberry Pi Model B";`

ARM: bcm2835: Add Raspberry Pi's ACT LED to DT The Raspberry Pi board has one GPIO-controlled LED labeled "ACT". Add it to the DT via the gpio-leds driver, so users can control it from userspace. If CONFIG_LEDS_TRIGGER_HEARTBEAT is set, the LED will also signal some sign of life. The GPIO circuitry is low-active. And as the bootloader may decide to switch the LED on at boot time, the default state is 'keep'. Signed-off-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> 2013-04-29 03:49:52 +07:00			`leds {`
			`act {`
			`gpios = <&gpio 16 1>;`
			`};`
			`};`
ARM: add infra-structure for BCM2835 and Raspberry Pi The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic support for this SoC. http://www.broadcom.com/products/BCM2835 http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf Note that the documentation in the latter .pdf assumes the MMU setup that's used on the "VideoCore" companion processor, and does not document physical peripheral addresses. Subtract 0x5e000000 to obtain the physical addresses. This is accounted for by the ranges property in the /soc node in the device tree. The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a minimal device tree for this board; enough to see some very early kernel boot messages through earlyprintk. However, this patch does not yet provide a useful booting system. http://www.raspberrypi.org/. This patch was extracted from git://github.com/lp0/linux.git branch rpi-split from 3-4 months ago, and significantly stripped down and modified since. Signed-off-by: Chris Boot <bootc@bootc.net> Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Dom Cobley <popcornmix@gmail.com> Signed-off-by: Dom Cobley <dc4@broadcom.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Arnd Bergmann <arnd@arndb.de> 2012-05-26 14:04:43 +07:00			`};`
ARM: bcm2835: enable GPIO/pinctrl Enable GPIO and pinctrl in Kconfig. Add required <mach/gpio.h> for gpiolib. Instantiate the BCM2835 GPIO module in bcm2835.dtsi. Add a pinctrl definition to bcm2835-rpi-b.dts that sets up all of the board's required pinmux configuration. GPIO aren't specified; that's left to gpio_request(). Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> 2012-09-28 10:54:21 +07:00
			`&gpio {`
ARM: bcm2835: dt: Raspberry Pi Model B had no I2S It's the Model B rev2 that had it. Remove it. Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Signed-off-by: Eric Anholt <eric@anholt.net> 2015-10-12 02:37:15 +07:00			`pinctrl-0 = <&gpioout &alt0 &alt3>;`
ARM: bcm2835: enable GPIO/pinctrl Enable GPIO and pinctrl in Kconfig. Add required <mach/gpio.h> for gpiolib. Instantiate the BCM2835 GPIO module in bcm2835.dtsi. Add a pinctrl definition to bcm2835-rpi-b.dts that sets up all of the board's required pinmux configuration. GPIO aren't specified; that's left to gpio_request(). Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> 2012-09-28 10:54:21 +07:00			`};`
ARM: bcm2835: Add VC4 to the device tree. VC4 is the GPU (display and 3D) present on the 283x. Signed-off-by: Eric Anholt <eric@anholt.net> Acked-by: Stephen Warren <swarren@wwwdotorg.org> 2015-03-03 05:36:16 +07:00
			`&hdmi {`
			`hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;`
			`};`