mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-11-25 13:30:57 +07:00
71 lines
2.7 KiB
C
71 lines
2.7 KiB
C
|
#ifndef __LINUX_ATMEL_PWM_H
|
||
|
|
#define __LINUX_ATMEL_PWM_H
|
||
|
|
|
||
|
|
/**
|
||
|
|
* struct pwm_channel - driver handle to a PWM channel
|
||
|
|
* @regs: base of this channel's registers
|
||
|
|
* @index: number of this channel (0..31)
|
||
|
|
* @mck: base clock rate, which can be prescaled and maybe subdivided
|
||
|
|
*
|
||
|
|
* Drivers initialize a pwm_channel structure using pwm_channel_alloc().
|
||
|
|
* Then they configure its clock rate (derived from MCK), alignment,
|
||
|
|
* polarity, and duty cycle by writing directly to the channel registers,
|
||
|
|
* before enabling the channel by calling pwm_channel_enable().
|
||
|
|
*
|
||
|
|
* After emitting a PWM signal for the desired length of time, drivers
|
||
|
|
* may then pwm_channel_disable() or pwm_channel_free(). Both of these
|
||
|
|
* disable the channel, but when it's freed the IRQ is deconfigured and
|
||
|
|
* the channel must later be re-allocated and reconfigured.
|
||
|
|
*
|
||
|
|
* Note that if the period or duty cycle need to be changed while the
|
||
|
|
* PWM channel is operating, drivers must use the PWM_CUPD double buffer
|
||
|
|
* mechanism, either polling until they change or getting implicitly
|
||
|
|
* notified through a once-per-period interrupt handler.
|
||
|
|
*/
|
||
|
|
struct pwm_channel {
|
||
|
|
void __iomem *regs;
|
||
|
|
unsigned index;
|
||
|
|
unsigned long mck;
|
||
|
|
};
|
||
|
|
|
||
|
|
extern int pwm_channel_alloc(int index, struct pwm_channel *ch);
|
||
|
|
extern int pwm_channel_free(struct pwm_channel *ch);
|
||
|
|
|
||
|
|
extern int pwm_clk_alloc(unsigned prescale, unsigned div);
|
||
|
|
extern void pwm_clk_free(unsigned clk);
|
||
|
|
|
||
|
|
extern int __pwm_channel_onoff(struct pwm_channel *ch, int enabled);
|
||
|
|
|
||
|
|
#define pwm_channel_enable(ch) __pwm_channel_onoff((ch), 1)
|
||
|
|
#define pwm_channel_disable(ch) __pwm_channel_onoff((ch), 0)
|
||
|
|
|
||
|
|
/* periodic interrupts, mostly for CUPD changes to period or cycle */
|
||
|
|
extern int pwm_channel_handler(struct pwm_channel *ch,
|
||
|
|
void (*handler)(struct pwm_channel *ch));
|
||
|
|
|
||
|
|
/* per-channel registers (banked at pwm_channel->regs) */
|
||
|
|
#define PWM_CMR 0x00 /* mode register */
|
||
|
|
#define PWM_CPR_CPD (1 << 10) /* set: CUPD modifies period */
|
||
|
|
#define PWM_CPR_CPOL (1 << 9) /* set: idle high */
|
||
|
|
#define PWM_CPR_CALG (1 << 8) /* set: center align */
|
||
|
|
#define PWM_CPR_CPRE (0xf << 0) /* mask: rate is mck/(2^pre) */
|
||
|
|
#define PWM_CPR_CLKA (0xb << 0) /* rate CLKA */
|
||
|
|
#define PWM_CPR_CLKB (0xc << 0) /* rate CLKB */
|
||
|
|
#define PWM_CDTY 0x04 /* duty cycle (max of CPRD) */
|
||
|
|
#define PWM_CPRD 0x08 /* period (count up from zero) */
|
||
|
|
#define PWM_CCNT 0x0c /* counter (20 bits?) */
|
||
|
|
#define PWM_CUPD 0x10 /* update CPRD (or CDTY) next period */
|
||
|
|
|
||
|
|
static inline void
|
||
|
|
pwm_channel_writel(struct pwm_channel *pwmc, unsigned offset, u32 val)
|
||
|
|
{
|
||
|
|
__raw_writel(val, pwmc->regs + offset);
|
||
|
|
}
|
||
|
|
|
||
|
|
static inline u32 pwm_channel_readl(struct pwm_channel *pwmc, unsigned offset)
|
||
|
|
{
|
||
|
|
return __raw_readl(pwmc->regs + offset);
|
||
|
|
}
|
||
|
|
|
||
|
|
#endif /* __LINUX_ATMEL_PWM_H */
|