mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-21 07:09:15 +07:00
51 lines
1.9 KiB
Plaintext
51 lines
1.9 KiB
Plaintext
|
=== ST Microelectronics SPEAr SPI CS Driver ===
|
||
|
|
|
||
|
|
SPEAr platform provides a provision to control chipselects of ARM PL022 Prime
|
||
|
|
Cell spi controller through its system registers, which otherwise remains under
|
||
|
|
PL022 control. If chipselect remain under PL022 control then they would be
|
||
|
|
released as soon as transfer is over and TxFIFO becomes empty. This is not
|
||
|
|
desired by some of the device protocols above spi which expect (multiple)
|
||
|
|
transfers without releasing their chipselects.
|
||
|
|
|
||
|
|
Chipselects can be controlled by software by turning them as GPIOs. SPEAr
|
||
|
|
provides another interface through system registers through which software can
|
||
|
|
directly control each PL022 chipselect. Hence, it is natural for SPEAr to export
|
||
|
|
the control of this interface as gpio.
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
|
||
|
|
* compatible: should be defined as "st,spear-spics-gpio"
|
||
|
|
* reg: mentioning address range of spics controller
|
||
|
|
* st-spics,peripcfg-reg: peripheral configuration register offset
|
||
|
|
* st-spics,sw-enable-bit: bit offset to enable sw control
|
||
|
|
* st-spics,cs-value-bit: bit offset to drive chipselect low or high
|
||
|
|
* st-spics,cs-enable-mask: chip select number bit mask
|
||
|
|
* st-spics,cs-enable-shift: chip select number program offset
|
||
|
|
* gpio-controller: Marks the device node as gpio controller
|
||
|
|
* #gpio-cells: should be 1 and will mention chip select number
|
||
|
|
|
||
|
|
All the above bit offsets are within peripcfg register.
|
||
|
|
|
||
|
|
Example:
|
||
|
|
-------
|
||
|
|
spics: spics@e0700000{
|
||
|
|
compatible = "st,spear-spics-gpio";
|
||
|
|
reg = <0xe0700000 0x1000>;
|
||
|
|
st-spics,peripcfg-reg = <0x3b0>;
|
||
|
|
st-spics,sw-enable-bit = <12>;
|
||
|
|
st-spics,cs-value-bit = <11>;
|
||
|
|
st-spics,cs-enable-mask = <3>;
|
||
|
|
st-spics,cs-enable-shift = <8>;
|
||
|
|
gpio-controller;
|
||
|
|
#gpio-cells = <2>;
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
spi0: spi@e0100000 {
|
||
|
|
status = "okay";
|
||
|
|
num-cs = <3>;
|
||
|
|
cs-gpios = <&gpio1 7 0>, <&spics 0>,
|
||
|
|
<&spics 1>;
|
||
|
|
...
|
||
|
|
}
|