linux_dsm_epyc7002/drivers/media/rc/fintek-cir.c

686 lines
18 KiB
C
Raw Normal View History

[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
/*
* Driver for Feature Integration Technology Inc. (aka Fintek) LPC CIR
*
* Copyright (C) 2011 Jarod Wilson <jarod@redhat.com>
*
* Special thanks to Fintek for providing hardware and spec sheets.
* This driver is based upon the nuvoton, ite and ene drivers for
* similar hardware.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pnp.h>
#include <linux/io.h>
#include <linux/interrupt.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <media/rc-core.h>
#include "fintek-cir.h"
/* write val to config reg */
static inline void fintek_cr_write(struct fintek_dev *fintek, u8 val, u8 reg)
{
fit_dbg("%s: reg 0x%02x, val 0x%02x (ip/dp: %02x/%02x)",
__func__, reg, val, fintek->cr_ip, fintek->cr_dp);
outb(reg, fintek->cr_ip);
outb(val, fintek->cr_dp);
}
/* read val from config reg */
static inline u8 fintek_cr_read(struct fintek_dev *fintek, u8 reg)
{
u8 val;
outb(reg, fintek->cr_ip);
val = inb(fintek->cr_dp);
fit_dbg("%s: reg 0x%02x, val 0x%02x (ip/dp: %02x/%02x)",
__func__, reg, val, fintek->cr_ip, fintek->cr_dp);
return val;
}
/* update config register bit without changing other bits */
static inline void fintek_set_reg_bit(struct fintek_dev *fintek, u8 val, u8 reg)
{
u8 tmp = fintek_cr_read(fintek, reg) | val;
fintek_cr_write(fintek, tmp, reg);
}
/* clear config register bit without changing other bits */
static inline void fintek_clear_reg_bit(struct fintek_dev *fintek, u8 val, u8 reg)
{
u8 tmp = fintek_cr_read(fintek, reg) & ~val;
fintek_cr_write(fintek, tmp, reg);
}
/* enter config mode */
static inline void fintek_config_mode_enable(struct fintek_dev *fintek)
{
/* Enabling Config Mode explicitly requires writing 2x */
outb(CONFIG_REG_ENABLE, fintek->cr_ip);
outb(CONFIG_REG_ENABLE, fintek->cr_ip);
}
/* exit config mode */
static inline void fintek_config_mode_disable(struct fintek_dev *fintek)
{
outb(CONFIG_REG_DISABLE, fintek->cr_ip);
}
/*
* When you want to address a specific logical device, write its logical
* device number to GCR_LOGICAL_DEV_NO
*/
static inline void fintek_select_logical_dev(struct fintek_dev *fintek, u8 ldev)
{
fintek_cr_write(fintek, ldev, GCR_LOGICAL_DEV_NO);
}
/* write val to cir config register */
static inline void fintek_cir_reg_write(struct fintek_dev *fintek, u8 val, u8 offset)
{
outb(val, fintek->cir_addr + offset);
}
/* read val from cir config register */
static u8 fintek_cir_reg_read(struct fintek_dev *fintek, u8 offset)
{
return inb(fintek->cir_addr + offset);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
}
/* dump current cir register contents */
static void cir_dump_regs(struct fintek_dev *fintek)
{
fintek_config_mode_enable(fintek);
fintek_select_logical_dev(fintek, fintek->logical_dev_cir);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
pr_info("%s: Dump CIR logical device registers:\n", FINTEK_DRIVER_NAME);
pr_info(" * CR CIR BASE ADDR: 0x%x\n",
(fintek_cr_read(fintek, CIR_CR_BASE_ADDR_HI) << 8) |
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_cr_read(fintek, CIR_CR_BASE_ADDR_LO));
pr_info(" * CR CIR IRQ NUM: 0x%x\n",
fintek_cr_read(fintek, CIR_CR_IRQ_SEL));
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_config_mode_disable(fintek);
pr_info("%s: Dump CIR registers:\n", FINTEK_DRIVER_NAME);
pr_info(" * STATUS: 0x%x\n",
fintek_cir_reg_read(fintek, CIR_STATUS));
pr_info(" * CONTROL: 0x%x\n",
fintek_cir_reg_read(fintek, CIR_CONTROL));
pr_info(" * RX_DATA: 0x%x\n",
fintek_cir_reg_read(fintek, CIR_RX_DATA));
pr_info(" * TX_CONTROL: 0x%x\n",
fintek_cir_reg_read(fintek, CIR_TX_CONTROL));
pr_info(" * TX_DATA: 0x%x\n",
fintek_cir_reg_read(fintek, CIR_TX_DATA));
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
}
/* detect hardware features */
static int fintek_hw_detect(struct fintek_dev *fintek)
{
unsigned long flags;
u8 chip_major, chip_minor;
u8 vendor_major, vendor_minor;
u8 portsel, ir_class;
u16 vendor, chip;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_config_mode_enable(fintek);
/* Check if we're using config port 0x4e or 0x2e */
portsel = fintek_cr_read(fintek, GCR_CONFIG_PORT_SEL);
if (portsel == 0xff) {
fit_pr(KERN_INFO, "first portsel read was bunk, trying alt");
fintek_config_mode_disable(fintek);
fintek->cr_ip = CR_INDEX_PORT2;
fintek->cr_dp = CR_DATA_PORT2;
fintek_config_mode_enable(fintek);
portsel = fintek_cr_read(fintek, GCR_CONFIG_PORT_SEL);
}
fit_dbg("portsel reg: 0x%02x", portsel);
ir_class = fintek_cir_reg_read(fintek, CIR_CR_CLASS);
fit_dbg("ir_class reg: 0x%02x", ir_class);
switch (ir_class) {
case CLASS_RX_2TX:
case CLASS_RX_1TX:
fintek->hw_tx_capable = true;
break;
case CLASS_RX_ONLY:
default:
fintek->hw_tx_capable = false;
break;
}
chip_major = fintek_cr_read(fintek, GCR_CHIP_ID_HI);
chip_minor = fintek_cr_read(fintek, GCR_CHIP_ID_LO);
chip = chip_major << 8 | chip_minor;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
vendor_major = fintek_cr_read(fintek, GCR_VENDOR_ID_HI);
vendor_minor = fintek_cr_read(fintek, GCR_VENDOR_ID_LO);
vendor = vendor_major << 8 | vendor_minor;
if (vendor != VENDOR_ID_FINTEK)
fit_pr(KERN_WARNING, "Unknown vendor ID: 0x%04x", vendor);
else
fit_dbg("Read Fintek vendor ID from chip");
fintek_config_mode_disable(fintek);
spin_lock_irqsave(&fintek->fintek_lock, flags);
fintek->chip_major = chip_major;
fintek->chip_minor = chip_minor;
fintek->chip_vendor = vendor;
/*
* Newer reviews of this chipset uses port 8 instead of 5
*/
if ((chip != 0x0408) && (chip != 0x0804))
fintek->logical_dev_cir = LOGICAL_DEV_CIR_REV2;
else
fintek->logical_dev_cir = LOGICAL_DEV_CIR_REV1;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
spin_unlock_irqrestore(&fintek->fintek_lock, flags);
return 0;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
}
static void fintek_cir_ldev_init(struct fintek_dev *fintek)
{
/* Select CIR logical device and enable */
fintek_select_logical_dev(fintek, fintek->logical_dev_cir);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_cr_write(fintek, LOGICAL_DEV_ENABLE, CIR_CR_DEV_EN);
/* Write allocated CIR address and IRQ information to hardware */
fintek_cr_write(fintek, fintek->cir_addr >> 8, CIR_CR_BASE_ADDR_HI);
fintek_cr_write(fintek, fintek->cir_addr & 0xff, CIR_CR_BASE_ADDR_LO);
fintek_cr_write(fintek, fintek->cir_irq, CIR_CR_IRQ_SEL);
fit_dbg("CIR initialized, base io address: 0x%lx, irq: %d (len: %d)",
fintek->cir_addr, fintek->cir_irq, fintek->cir_port_len);
}
/* enable CIR interrupts */
static void fintek_enable_cir_irq(struct fintek_dev *fintek)
{
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_EN, CIR_STATUS);
}
static void fintek_cir_regs_init(struct fintek_dev *fintek)
{
/* clear any and all stray interrupts */
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_MASK, CIR_STATUS);
/* and finally, enable interrupts */
fintek_enable_cir_irq(fintek);
}
static void fintek_enable_wake(struct fintek_dev *fintek)
{
fintek_config_mode_enable(fintek);
fintek_select_logical_dev(fintek, LOGICAL_DEV_ACPI);
/* Allow CIR PME's to wake system */
fintek_set_reg_bit(fintek, ACPI_WAKE_EN_CIR_BIT, LDEV_ACPI_WAKE_EN_REG);
/* Enable CIR PME's */
fintek_set_reg_bit(fintek, ACPI_PME_CIR_BIT, LDEV_ACPI_PME_EN_REG);
/* Clear CIR PME status register */
fintek_set_reg_bit(fintek, ACPI_PME_CIR_BIT, LDEV_ACPI_PME_CLR_REG);
/* Save state */
fintek_set_reg_bit(fintek, ACPI_STATE_CIR_BIT, LDEV_ACPI_STATE_REG);
fintek_config_mode_disable(fintek);
}
static int fintek_cmdsize(u8 cmd, u8 subcmd)
{
int datasize = 0;
switch (cmd) {
case BUF_COMMAND_NULL:
if (subcmd == BUF_HW_CMD_HEADER)
datasize = 1;
break;
case BUF_HW_CMD_HEADER:
if (subcmd == BUF_CMD_G_REVISION)
datasize = 2;
break;
case BUF_COMMAND_HEADER:
switch (subcmd) {
case BUF_CMD_S_CARRIER:
case BUF_CMD_S_TIMEOUT:
case BUF_RSP_PULSE_COUNT:
datasize = 2;
break;
case BUF_CMD_SIG_END:
case BUF_CMD_S_TXMASK:
case BUF_CMD_S_RXSENSOR:
datasize = 1;
break;
}
}
return datasize;
}
/* process ir data stored in driver buffer */
static void fintek_process_rx_ir_data(struct fintek_dev *fintek)
{
DEFINE_IR_RAW_EVENT(rawir);
u8 sample;
bool event = false;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
int i;
for (i = 0; i < fintek->pkts; i++) {
sample = fintek->buf[i];
switch (fintek->parser_state) {
case CMD_HEADER:
fintek->cmd = sample;
if ((fintek->cmd == BUF_COMMAND_HEADER) ||
((fintek->cmd & BUF_COMMAND_MASK) !=
BUF_PULSE_BIT)) {
fintek->parser_state = SUBCMD;
continue;
}
fintek->rem = (fintek->cmd & BUF_LEN_MASK);
fit_dbg("%s: rem: 0x%02x", __func__, fintek->rem);
if (fintek->rem)
fintek->parser_state = PARSE_IRDATA;
else
ir_raw_event_reset(fintek->rdev);
break;
case SUBCMD:
fintek->rem = fintek_cmdsize(fintek->cmd, sample);
fintek->parser_state = CMD_DATA;
break;
case CMD_DATA:
fintek->rem--;
break;
case PARSE_IRDATA:
fintek->rem--;
init_ir_raw_event(&rawir);
rawir.pulse = ((sample & BUF_PULSE_BIT) != 0);
rawir.duration = US_TO_NS((sample & BUF_SAMPLE_MASK)
* CIR_SAMPLE_PERIOD);
fit_dbg("Storing %s with duration %d",
rawir.pulse ? "pulse" : "space",
rawir.duration);
if (ir_raw_event_store_with_filter(fintek->rdev,
&rawir))
event = true;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
break;
}
if ((fintek->parser_state != CMD_HEADER) && !fintek->rem)
fintek->parser_state = CMD_HEADER;
}
fintek->pkts = 0;
if (event) {
fit_dbg("Calling ir_raw_event_handle");
ir_raw_event_handle(fintek->rdev);
}
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
}
/* copy data from hardware rx register into driver buffer */
static void fintek_get_rx_ir_data(struct fintek_dev *fintek, u8 rx_irqs)
{
unsigned long flags;
u8 sample, status;
spin_lock_irqsave(&fintek->fintek_lock, flags);
/*
* We must read data from CIR_RX_DATA until the hardware IR buffer
* is empty and clears the RX_TIMEOUT and/or RX_RECEIVE flags in
* the CIR_STATUS register
*/
do {
sample = fintek_cir_reg_read(fintek, CIR_RX_DATA);
fit_dbg("%s: sample: 0x%02x", __func__, sample);
fintek->buf[fintek->pkts] = sample;
fintek->pkts++;
status = fintek_cir_reg_read(fintek, CIR_STATUS);
if (!(status & CIR_STATUS_IRQ_EN))
break;
} while (status & rx_irqs);
fintek_process_rx_ir_data(fintek);
spin_unlock_irqrestore(&fintek->fintek_lock, flags);
}
static void fintek_cir_log_irqs(u8 status)
{
fit_pr(KERN_INFO, "IRQ 0x%02x:%s%s%s%s%s", status,
status & CIR_STATUS_IRQ_EN ? " IRQEN" : "",
status & CIR_STATUS_TX_FINISH ? " TXF" : "",
status & CIR_STATUS_TX_UNDERRUN ? " TXU" : "",
status & CIR_STATUS_RX_TIMEOUT ? " RXTO" : "",
status & CIR_STATUS_RX_RECEIVE ? " RXOK" : "");
}
/* interrupt service routine for incoming and outgoing CIR data */
static irqreturn_t fintek_cir_isr(int irq, void *data)
{
struct fintek_dev *fintek = data;
u8 status, rx_irqs;
fit_dbg_verbose("%s firing", __func__);
fintek_config_mode_enable(fintek);
fintek_select_logical_dev(fintek, fintek->logical_dev_cir);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_config_mode_disable(fintek);
/*
* Get IR Status register contents. Write 1 to ack/clear
*
* bit: reg name - description
* 3: TX_FINISH - TX is finished
* 2: TX_UNDERRUN - TX underrun
* 1: RX_TIMEOUT - RX data timeout
* 0: RX_RECEIVE - RX data received
*/
status = fintek_cir_reg_read(fintek, CIR_STATUS);
if (!(status & CIR_STATUS_IRQ_MASK) || status == 0xff) {
fit_dbg_verbose("%s exiting, IRSTS 0x%02x", __func__, status);
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_MASK, CIR_STATUS);
return IRQ_RETVAL(IRQ_NONE);
}
if (debug)
fintek_cir_log_irqs(status);
rx_irqs = status & (CIR_STATUS_RX_RECEIVE | CIR_STATUS_RX_TIMEOUT);
if (rx_irqs)
fintek_get_rx_ir_data(fintek, rx_irqs);
/* ack/clear all irq flags we've got */
fintek_cir_reg_write(fintek, status, CIR_STATUS);
fit_dbg_verbose("%s done", __func__);
return IRQ_RETVAL(IRQ_HANDLED);
}
static void fintek_enable_cir(struct fintek_dev *fintek)
{
/* set IRQ enabled */
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_EN, CIR_STATUS);
fintek_config_mode_enable(fintek);
/* enable the CIR logical device */
fintek_select_logical_dev(fintek, fintek->logical_dev_cir);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_cr_write(fintek, LOGICAL_DEV_ENABLE, CIR_CR_DEV_EN);
fintek_config_mode_disable(fintek);
/* clear all pending interrupts */
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_MASK, CIR_STATUS);
/* enable interrupts */
fintek_enable_cir_irq(fintek);
}
static void fintek_disable_cir(struct fintek_dev *fintek)
{
fintek_config_mode_enable(fintek);
/* disable the CIR logical device */
fintek_select_logical_dev(fintek, fintek->logical_dev_cir);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_cr_write(fintek, LOGICAL_DEV_DISABLE, CIR_CR_DEV_EN);
fintek_config_mode_disable(fintek);
}
static int fintek_open(struct rc_dev *dev)
{
struct fintek_dev *fintek = dev->priv;
unsigned long flags;
spin_lock_irqsave(&fintek->fintek_lock, flags);
fintek_enable_cir(fintek);
spin_unlock_irqrestore(&fintek->fintek_lock, flags);
return 0;
}
static void fintek_close(struct rc_dev *dev)
{
struct fintek_dev *fintek = dev->priv;
unsigned long flags;
spin_lock_irqsave(&fintek->fintek_lock, flags);
fintek_disable_cir(fintek);
spin_unlock_irqrestore(&fintek->fintek_lock, flags);
}
/* Allocate memory, probe hardware, and initialize everything */
static int fintek_probe(struct pnp_dev *pdev, const struct pnp_device_id *dev_id)
{
struct fintek_dev *fintek;
struct rc_dev *rdev;
int ret = -ENOMEM;
fintek = kzalloc(sizeof(struct fintek_dev), GFP_KERNEL);
if (!fintek)
return ret;
/* input device for IR remote (and tx) */
rdev = rc_allocate_device(RC_DRIVER_IR_RAW);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
if (!rdev)
goto exit_free_dev_rdev;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
ret = -ENODEV;
/* validate pnp resources */
if (!pnp_port_valid(pdev, 0)) {
dev_err(&pdev->dev, "IR PNP Port not valid!\n");
goto exit_free_dev_rdev;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
}
if (!pnp_irq_valid(pdev, 0)) {
dev_err(&pdev->dev, "IR PNP IRQ not valid!\n");
goto exit_free_dev_rdev;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
}
fintek->cir_addr = pnp_port_start(pdev, 0);
fintek->cir_irq = pnp_irq(pdev, 0);
fintek->cir_port_len = pnp_port_len(pdev, 0);
fintek->cr_ip = CR_INDEX_PORT;
fintek->cr_dp = CR_DATA_PORT;
spin_lock_init(&fintek->fintek_lock);
pnp_set_drvdata(pdev, fintek);
fintek->pdev = pdev;
ret = fintek_hw_detect(fintek);
if (ret)
goto exit_free_dev_rdev;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
/* Initialize CIR & CIR Wake Logical Devices */
fintek_config_mode_enable(fintek);
fintek_cir_ldev_init(fintek);
fintek_config_mode_disable(fintek);
/* Initialize CIR & CIR Wake Config Registers */
fintek_cir_regs_init(fintek);
/* Set up the rc device */
rdev->priv = fintek;
rdev->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
rdev->open = fintek_open;
rdev->close = fintek_close;
rdev->device_name = FINTEK_DESCRIPTION;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
rdev->input_phys = "fintek/cir0";
rdev->input_id.bustype = BUS_HOST;
rdev->input_id.vendor = VENDOR_ID_FINTEK;
rdev->input_id.product = fintek->chip_major;
rdev->input_id.version = fintek->chip_minor;
rdev->dev.parent = &pdev->dev;
rdev->driver_name = FINTEK_DRIVER_NAME;
rdev->map_name = RC_MAP_RC6_MCE;
rdev->timeout = US_TO_NS(1000);
/* rx resolution is hardwired to 50us atm, 1, 25, 100 also possible */
rdev->rx_resolution = US_TO_NS(CIR_SAMPLE_PERIOD);
fintek->rdev = rdev;
ret = -EBUSY;
/* now claim resources */
if (!request_region(fintek->cir_addr,
fintek->cir_port_len, FINTEK_DRIVER_NAME))
goto exit_free_dev_rdev;
if (request_irq(fintek->cir_irq, fintek_cir_isr, IRQF_SHARED,
FINTEK_DRIVER_NAME, (void *)fintek))
goto exit_free_cir_addr;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
ret = rc_register_device(rdev);
if (ret)
goto exit_free_irq;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
device_init_wakeup(&pdev->dev, true);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fit_pr(KERN_NOTICE, "driver has been successfully loaded\n");
if (debug)
cir_dump_regs(fintek);
return 0;
exit_free_irq:
free_irq(fintek->cir_irq, fintek);
exit_free_cir_addr:
release_region(fintek->cir_addr, fintek->cir_port_len);
exit_free_dev_rdev:
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
rc_free_device(rdev);
kfree(fintek);
return ret;
}
static void fintek_remove(struct pnp_dev *pdev)
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
{
struct fintek_dev *fintek = pnp_get_drvdata(pdev);
unsigned long flags;
spin_lock_irqsave(&fintek->fintek_lock, flags);
/* disable CIR */
fintek_disable_cir(fintek);
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_MASK, CIR_STATUS);
/* enable CIR Wake (for IR power-on) */
fintek_enable_wake(fintek);
spin_unlock_irqrestore(&fintek->fintek_lock, flags);
/* free resources */
free_irq(fintek->cir_irq, fintek);
release_region(fintek->cir_addr, fintek->cir_port_len);
rc_unregister_device(fintek->rdev);
kfree(fintek);
}
static int fintek_suspend(struct pnp_dev *pdev, pm_message_t state)
{
struct fintek_dev *fintek = pnp_get_drvdata(pdev);
unsigned long flags;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fit_dbg("%s called", __func__);
spin_lock_irqsave(&fintek->fintek_lock, flags);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
/* disable all CIR interrupts */
fintek_cir_reg_write(fintek, CIR_STATUS_IRQ_MASK, CIR_STATUS);
spin_unlock_irqrestore(&fintek->fintek_lock, flags);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_config_mode_enable(fintek);
/* disable cir logical dev */
fintek_select_logical_dev(fintek, fintek->logical_dev_cir);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_cr_write(fintek, LOGICAL_DEV_DISABLE, CIR_CR_DEV_EN);
fintek_config_mode_disable(fintek);
/* make sure wake is enabled */
fintek_enable_wake(fintek);
return 0;
}
static int fintek_resume(struct pnp_dev *pdev)
{
struct fintek_dev *fintek = pnp_get_drvdata(pdev);
fit_dbg("%s called", __func__);
/* open interrupt */
fintek_enable_cir_irq(fintek);
/* Enable CIR logical device */
fintek_config_mode_enable(fintek);
fintek_select_logical_dev(fintek, fintek->logical_dev_cir);
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
fintek_cr_write(fintek, LOGICAL_DEV_ENABLE, CIR_CR_DEV_EN);
fintek_config_mode_disable(fintek);
fintek_cir_regs_init(fintek);
return 0;
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
}
static void fintek_shutdown(struct pnp_dev *pdev)
{
struct fintek_dev *fintek = pnp_get_drvdata(pdev);
fintek_enable_wake(fintek);
}
static const struct pnp_device_id fintek_ids[] = {
{ "FIT0002", 0 }, /* CIR */
{ "", 0 },
};
static struct pnp_driver fintek_driver = {
.name = FINTEK_DRIVER_NAME,
.id_table = fintek_ids,
.flags = PNP_DRIVER_RES_DO_NOT_CHANGE,
.probe = fintek_probe,
.remove = fintek_remove,
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function This is a new driver for the Fintek LPC SuperIO CIR function, in the Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so thanks go to them for supporting this effort. This driver started out as a copy of the nuvoton-cir driver, and was then modified as needed for the Fintek chip. The two share many similaries, though the buffer handling for the Fintek chip is actually nearly identical to the mceusb buffer handling, so the parser routine is almost a drop-in copy of the mceusb buffer parser (a candidate for being abstracted out into shared code at some point). This initial code drop *only* supports receive, but the hardware does support transmit as well. I really haven't even started to look at what's required, but my guess is that its also pretty similar to mceusb. Most people are probably only really interested in RX anyway though, so I think its good to get this out there even with only RX. (Nb: there are also Fintek-made mceusb receivers, which presumably, this chip shares CIR hardware with). This hardware can be found on at least Jetway NC98 boards and derivative systems, and likely others as well. Functionality was tested with an NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge) and NEC-ish (tivo) remotes all successful, as was lirc userspace decode of the RC6 remote. CC: Aaron Huang <aaron_huang@fintek.com.tw> CC: Tom Tsai <tom_tsai@fintek.com.tw> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-05-25 23:35:13 +07:00
.suspend = fintek_suspend,
.resume = fintek_resume,
.shutdown = fintek_shutdown,
};
module_param(debug, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(debug, "Enable debugging output");
MODULE_DEVICE_TABLE(pnp, fintek_ids);
MODULE_DESCRIPTION(FINTEK_DESCRIPTION " driver");
MODULE_AUTHOR("Jarod Wilson <jarod@redhat.com>");
MODULE_LICENSE("GPL");
module_pnp_driver(fintek_driver);