linux_dsm_epyc7002/drivers/scsi/sd.h

329 lines
8.5 KiB
C
Raw Normal View History

#ifndef _SCSI_DISK_H
#define _SCSI_DISK_H
/*
* More than enough for everybody ;) The huge number of majors
* is a leftover from 16bit dev_t days, we don't really need that
* much numberspace.
*/
#define SD_MAJORS 16
/*
* Time out in seconds for disks and Magneto-opticals (which are slower).
*/
#define SD_TIMEOUT (30 * HZ)
#define SD_MOD_TIMEOUT (75 * HZ)
/*
* Flush timeout is a multiplier over the standard device timeout which is
* user modifiable via sysfs but initially set to SD_TIMEOUT
*/
#define SD_FLUSH_TIMEOUT_MULTIPLIER 2
#define SD_WRITE_SAME_TIMEOUT (120 * HZ)
/*
* Number of allowed retries
*/
#define SD_MAX_RETRIES 5
#define SD_PASSTHROUGH_RETRIES 1
#define SD_MAX_MEDIUM_TIMEOUTS 2
/*
* Size of the initial data buffer for mode and read capacity data
*/
#define SD_BUF_SIZE 512
/*
* Number of sectors at the end of the device to avoid multi-sector
* accesses to in the case of last_sector_bug
*/
#define SD_LAST_BUGGY_SECTORS 8
enum {
SD_EXT_CDB_SIZE = 32, /* Extended CDB size */
SD_MEMPOOL_SIZE = 2, /* CDB pool size */
};
enum {
SD_DEF_XFER_BLOCKS = 0xffff,
SD_MAX_XFER_BLOCKS = 0xffffffff,
SD_MAX_WS10_BLOCKS = 0xffff,
SD_MAX_WS16_BLOCKS = 0x7fffff,
};
enum {
SD_LBP_FULL = 0, /* Full logical block provisioning */
SD_LBP_UNMAP, /* Use UNMAP command */
SD_LBP_WS16, /* Use WRITE SAME(16) with UNMAP bit */
SD_LBP_WS10, /* Use WRITE SAME(10) with UNMAP bit */
SD_LBP_ZERO, /* Use WRITE SAME(10) with zero payload */
SD_LBP_DISABLE, /* Discard disabled due to failed cmd */
};
enum {
SD_ZERO_WRITE = 0, /* Use WRITE(10/16) command */
SD_ZERO_WS, /* Use WRITE SAME(10/16) command */
SD_ZERO_WS16_UNMAP, /* Use WRITE SAME(16) with UNMAP */
SD_ZERO_WS10_UNMAP, /* Use WRITE SAME(10) with UNMAP */
};
struct scsi_disk {
struct scsi_driver *driver; /* always &sd_template */
struct scsi_device *device;
struct device dev;
struct gendisk *disk;
struct opal_dev *opal_dev;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 13:40:34 +07:00
#ifdef CONFIG_BLK_DEV_ZONED
unsigned int nr_zones;
unsigned int zone_blocks;
unsigned int zone_shift;
unsigned long *zones_wlock;
unsigned int zones_optimal_open;
unsigned int zones_optimal_nonseq;
unsigned int zones_max_open;
#endif
atomic_t openers;
sector_t capacity; /* size in logical blocks */
u32 max_xfer_blocks;
block/sd: Fix device-imposed transfer length limits Commit 4f258a46346c ("sd: Fix maximum I/O size for BLOCK_PC requests") had the unfortunate side-effect of removing an implicit clamp to BLK_DEF_MAX_SECTORS for REQ_TYPE_FS requests in the block layer code. This caused problems for some SMR drives. Debugging this issue revealed a few problems with the existing infrastructure since the block layer didn't know how to deal with device-imposed limits, only limits set by the I/O controller. - Introduce a new queue limit, max_dev_sectors, which is used by the ULD to signal the maximum sectors for a REQ_TYPE_FS request. - Ensure that max_dev_sectors is correctly stacked and taken into account when overriding max_sectors through sysfs. - Rework sd_read_block_limits() so it saves the max_xfer and opt_xfer values for later processing. - In sd_revalidate() set the queue's max_dev_sectors based on the MAXIMUM TRANSFER LENGTH value in the Block Limits VPD. If this value is not reported, fall back to a cap based on the CDB TRANSFER LENGTH field size. - In sd_revalidate(), use OPTIMAL TRANSFER LENGTH from the Block Limits VPD--if reported and sane--to signal the preferred device transfer size for FS requests. Otherwise use BLK_DEF_MAX_SECTORS. - blk_limits_max_hw_sectors() is no longer used and can be removed. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93581 Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: sweeneygj@gmx.com Tested-by: Arzeets <anatol.pomozov@gmail.com> Tested-by: David Eisner <david.eisner@oriel.oxon.org> Tested-by: Mario Kicherer <dev@kicherer.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2015-11-14 04:46:48 +07:00
u32 opt_xfer_blocks;
u32 max_ws_blocks;
u32 max_unmap_blocks;
u32 unmap_granularity;
u32 unmap_alignment;
u32 index;
unsigned int physical_block_size;
unsigned int max_medium_access_timeouts;
unsigned int medium_access_timed_out;
u8 media_present;
u8 write_prot;
u8 protection_type;/* Data Integrity Field */
u8 provisioning_mode;
u8 zeroing_mode;
unsigned ATO : 1; /* state of disk ATO bit */
unsigned cache_override : 1; /* temp override of WCE,RCD */
unsigned WCE : 1; /* state of disk WCE bit */
unsigned RCD : 1; /* state of disk RCD bit, unused */
unsigned DPOFUA : 1; /* state of disk DPOFUA bit */
unsigned first_scan : 1;
unsigned lbpme : 1;
unsigned lbprz : 1;
unsigned lbpu : 1;
unsigned lbpws : 1;
unsigned lbpws10 : 1;
unsigned lbpvpd : 1;
unsigned ws10 : 1;
unsigned ws16 : 1;
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 13:40:34 +07:00
unsigned rc_basis: 2;
unsigned zoned: 2;
unsigned urswrz : 1;
unsigned security : 1;
unsigned ignore_medium_access_errors : 1;
};
#define to_scsi_disk(obj) container_of(obj,struct scsi_disk,dev)
static inline struct scsi_disk *scsi_disk(struct gendisk *disk)
{
return container_of(disk->private_data, struct scsi_disk, driver);
}
#define sd_printk(prefix, sdsk, fmt, a...) \
(sdsk)->disk ? \
sdev_prefix_printk(prefix, (sdsk)->device, \
(sdsk)->disk->disk_name, fmt, ##a) : \
sdev_printk(prefix, (sdsk)->device, fmt, ##a)
#define sd_first_printk(prefix, sdsk, fmt, a...) \
do { \
if ((sdkp)->first_scan) \
sd_printk(prefix, sdsk, fmt, ##a); \
} while (0)
static inline int scsi_medium_access_command(struct scsi_cmnd *scmd)
{
switch (scmd->cmnd[0]) {
case READ_6:
case READ_10:
case READ_12:
case READ_16:
case SYNCHRONIZE_CACHE:
case VERIFY:
case VERIFY_12:
case VERIFY_16:
case WRITE_6:
case WRITE_10:
case WRITE_12:
case WRITE_16:
case WRITE_SAME:
case WRITE_SAME_16:
case UNMAP:
return 1;
case VARIABLE_LENGTH_CMD:
switch (scmd->cmnd[9]) {
case READ_32:
case VERIFY_32:
case WRITE_32:
case WRITE_SAME_32:
return 1;
}
}
return 0;
}
static inline sector_t logical_to_sectors(struct scsi_device *sdev, sector_t blocks)
{
return blocks << (ilog2(sdev->sector_size) - 9);
}
static inline unsigned int logical_to_bytes(struct scsi_device *sdev, sector_t blocks)
{
return blocks * sdev->sector_size;
}
static inline sector_t bytes_to_logical(struct scsi_device *sdev, unsigned int bytes)
{
return bytes >> ilog2(sdev->sector_size);
}
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 13:40:34 +07:00
static inline sector_t sectors_to_logical(struct scsi_device *sdev, sector_t sector)
{
return sector >> (ilog2(sdev->sector_size) - 9);
}
/*
* Look up the DIX operation based on whether the command is read or
* write and whether dix and dif are enabled.
*/
static inline unsigned int sd_prot_op(bool write, bool dix, bool dif)
{
/* Lookup table: bit 2 (write), bit 1 (dix), bit 0 (dif) */
const unsigned int ops[] = { /* wrt dix dif */
SCSI_PROT_NORMAL, /* 0 0 0 */
SCSI_PROT_READ_STRIP, /* 0 0 1 */
SCSI_PROT_READ_INSERT, /* 0 1 0 */
SCSI_PROT_READ_PASS, /* 0 1 1 */
SCSI_PROT_NORMAL, /* 1 0 0 */
SCSI_PROT_WRITE_INSERT, /* 1 0 1 */
SCSI_PROT_WRITE_STRIP, /* 1 1 0 */
SCSI_PROT_WRITE_PASS, /* 1 1 1 */
};
return ops[write << 2 | dix << 1 | dif];
}
/*
* Returns a mask of the protection flags that are valid for a given DIX
* operation.
*/
static inline unsigned int sd_prot_flag_mask(unsigned int prot_op)
{
const unsigned int flag_mask[] = {
[SCSI_PROT_NORMAL] = 0,
[SCSI_PROT_READ_STRIP] = SCSI_PROT_TRANSFER_PI |
SCSI_PROT_GUARD_CHECK |
SCSI_PROT_REF_CHECK |
SCSI_PROT_REF_INCREMENT,
[SCSI_PROT_READ_INSERT] = SCSI_PROT_REF_INCREMENT |
SCSI_PROT_IP_CHECKSUM,
[SCSI_PROT_READ_PASS] = SCSI_PROT_TRANSFER_PI |
SCSI_PROT_GUARD_CHECK |
SCSI_PROT_REF_CHECK |
SCSI_PROT_REF_INCREMENT |
SCSI_PROT_IP_CHECKSUM,
[SCSI_PROT_WRITE_INSERT] = SCSI_PROT_TRANSFER_PI |
SCSI_PROT_REF_INCREMENT,
[SCSI_PROT_WRITE_STRIP] = SCSI_PROT_GUARD_CHECK |
SCSI_PROT_REF_CHECK |
SCSI_PROT_REF_INCREMENT |
SCSI_PROT_IP_CHECKSUM,
[SCSI_PROT_WRITE_PASS] = SCSI_PROT_TRANSFER_PI |
SCSI_PROT_GUARD_CHECK |
SCSI_PROT_REF_CHECK |
SCSI_PROT_REF_INCREMENT |
SCSI_PROT_IP_CHECKSUM,
};
return flag_mask[prot_op];
}
#ifdef CONFIG_BLK_DEV_INTEGRITY
extern void sd_dif_config_host(struct scsi_disk *);
extern void sd_dif_prepare(struct scsi_cmnd *scmd);
extern void sd_dif_complete(struct scsi_cmnd *, unsigned int);
#else /* CONFIG_BLK_DEV_INTEGRITY */
static inline void sd_dif_config_host(struct scsi_disk *disk)
{
}
static inline int sd_dif_prepare(struct scsi_cmnd *scmd)
{
return 0;
}
static inline void sd_dif_complete(struct scsi_cmnd *cmd, unsigned int a)
{
}
#endif /* CONFIG_BLK_DEV_INTEGRITY */
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 13:40:34 +07:00
static inline int sd_is_zoned(struct scsi_disk *sdkp)
{
return sdkp->zoned == 1 || sdkp->device->type == TYPE_ZBC;
}
#ifdef CONFIG_BLK_DEV_ZONED
extern int sd_zbc_read_zones(struct scsi_disk *sdkp, unsigned char *buffer);
extern void sd_zbc_remove(struct scsi_disk *sdkp);
extern void sd_zbc_print_zones(struct scsi_disk *sdkp);
extern int sd_zbc_write_lock_zone(struct scsi_cmnd *cmd);
extern void sd_zbc_write_unlock_zone(struct scsi_cmnd *cmd);
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 13:40:34 +07:00
extern int sd_zbc_setup_report_cmnd(struct scsi_cmnd *cmd);
extern int sd_zbc_setup_reset_cmnd(struct scsi_cmnd *cmd);
extern void sd_zbc_complete(struct scsi_cmnd *cmd, unsigned int good_bytes,
struct scsi_sense_hdr *sshdr);
#else /* CONFIG_BLK_DEV_ZONED */
static inline int sd_zbc_read_zones(struct scsi_disk *sdkp,
unsigned char *buf)
{
return 0;
}
static inline void sd_zbc_remove(struct scsi_disk *sdkp) {}
static inline void sd_zbc_print_zones(struct scsi_disk *sdkp) {}
static inline int sd_zbc_write_lock_zone(struct scsi_cmnd *cmd)
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 13:40:34 +07:00
{
/* Let the drive fail requests */
return BLKPREP_OK;
}
static inline void sd_zbc_write_unlock_zone(struct scsi_cmnd *cmd) {}
sd: Implement support for ZBC devices Implement ZBC support functions to setup zoned disks, both host-managed and host-aware models. Only zoned disks that satisfy the following conditions are supported: 1) All zones are the same size, with the exception of an eventual last smaller runt zone. 2) For host-managed disks, reads are unrestricted (reads are not failed due to zone or write pointer alignement constraints). Zoned disks that do not satisfy these 2 conditions are setup with a capacity of 0 to prevent their use. The function sd_zbc_read_zones, called from sd_revalidate_disk, checks that the device satisfies the above two constraints. This function may also change the disk capacity previously set by sd_read_capacity for devices reporting only the capacity of conventional zones at the beginning of the LBA range (i.e. devices reporting rc_basis set to 0). The capacity message output was moved out of sd_read_capacity into a new function sd_print_capacity to include this eventual capacity change by sd_zbc_read_zones. This new function also includes a call to sd_zbc_print_zones to display the number of zones and zone size of the device. Signed-off-by: Hannes Reinecke <hare@suse.de> [Damien: * Removed zone cache support * Removed mapping of discard to reset write pointer command * Modified sd_zbc_read_zones to include checks that the device satisfies the kernel constraints * Implemeted REPORT ZONES setup and post-processing based on code from Shaun Tancheff <shaun.tancheff@seagate.com> * Removed confusing use of 512B sector units in functions interface] Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com> Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com> Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <axboe@fb.com>
2016-10-18 13:40:34 +07:00
static inline int sd_zbc_setup_report_cmnd(struct scsi_cmnd *cmd)
{
return BLKPREP_INVALID;
}
static inline int sd_zbc_setup_reset_cmnd(struct scsi_cmnd *cmd)
{
return BLKPREP_INVALID;
}
static inline void sd_zbc_complete(struct scsi_cmnd *cmd,
unsigned int good_bytes,
struct scsi_sense_hdr *sshdr) {}
#endif /* CONFIG_BLK_DEV_ZONED */
#endif /* _SCSI_DISK_H */