linux_dsm_epyc7002/drivers/infiniband/ulp/ipoib/Makefile

obj-$(CONFIG_INFINIBAND_IPOIB)			+= ib_ipoib.o

ib_ipoib-y					:= ipoib_main.o \
						   ipoib_ib.o \
						   ipoib_multicast.o \
						   ipoib_verbs.o \
						   ipoib_vlan.o \
						   ipoib_ethtool.o \
						   ipoib_netlink.o
ib_ipoib-$(CONFIG_INFINIBAND_IPOIB_CM)		+= ipoib_cm.o
ib_ipoib-$(CONFIG_INFINIBAND_IPOIB_DEBUG)	+= ipoib_fs.o
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 05:20:36 +07:00			`obj-$(CONFIG_INFINIBAND_IPOIB) += ib_ipoib.o`

			`ib_ipoib-y := ipoib_main.o \`
			`ipoib_ib.o \`
			`ipoib_multicast.o \`
			`ipoib_verbs.o \`
IPoIB: Add basic ethtool support Just add the infrastructure so we can add functionality later. Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com> 2008-04-17 11:09:32 +07:00			`ipoib_vlan.o \`
IB/ipoib: Add rtnl_link_ops support Add rtnl_link_ops to IPoIB, with the first usage being child device create/delete through them. Childs devices are now either legacy ones, created/deleted through the ipoib sysfs entries, or RTNL ones. Adding support for RTNL childs involved refactoring of ipoib_vlan_add which is now used by both the sysfs and the link_ops code. Also, added ndo_uninit entry to support calling unregister_netdevice_queue from the rtnl dellink entry. This required removal of calls to ipoib_dev_cleanup from the driver in flows which use unregister_netdevice, since the networking core will invoke ipoib_uninit which does exactly that. Signed-off-by: Erez Shitrit <erezsh@mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> 2012-09-13 12:56:36 +07:00			`ipoib_ethtool.o \`
			`ipoib_netlink.o`
IPoIB: Connected mode experimental support The following patch adds experimental support for IPoIB connected mode, as defined by the draft from the IETF ipoib working group. The idea is to increase performance by increasing the MTU from the maximum of 2K (theoretically 4K) supported by IPoIB on top of UD. With this code, I'm able to get 800MByte/sec or more with netperf without options on a Mellanox 4x back-to-back DDR system. Some notes on code: 1. SRQ is used for scalability to large cluster sizes 2. Only RC connections are used (UC does not support SRQ now) 3. Retry count is set to 0 since spec draft warns against retries 4. Each connection is used for data transfers in only 1 direction, so each connection is either active(TX) or passive (RX). 2 sides that want to communicate create 2 connections. 5. Each active (TX) connection has a separate CQ for send completions - this keeps the code simple without CQ resize and other tricks 6. To detect stale passive side connections (where the remote side is down), we keep an LRU list of passive connections (updated once per second per connection) and destroy a connection after it has been unused for several seconds. The LRU rule makes it possible to avoid scanning connections that have recently been active. Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com> 2007-02-06 03:12:23 +07:00			`ib_ipoib-$(CONFIG_INFINIBAND_IPOIB_CM) += ipoib_cm.o`
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-17 05:20:36 +07:00			`ib_ipoib-$(CONFIG_INFINIBAND_IPOIB_DEBUG) += ipoib_fs.o`