linux_dsm_epyc7002/drivers/phy/motorola/Makefile

#
# Makefile for the phy drivers.
#

obj-$(CONFIG_PHY_CPCAP_USB)		+= phy-cpcap-usb.o
obj-$(CONFIG_PHY_MAPPHONE_MDM6600)	+= phy-mapphone-mdm6600.o
phy: cpcap-usb: Add CPCAP PMIC USB support Some Motorola phones like droid 4 use a custom CPCAP PMIC that has a multiplexing USB PHY. This USB PHY can operate at least in four modes using pin multiplexing and two control GPIOS: - Pass through companion PHY for the SoC USB PHY - ULPI PHY for the SoC - Pass through USB for the modem - UART debug console for the SoC This patch adds support for droid 4 USB PHY and debug UART modes, support for other modes can be added later on as needed. Both peripheral and host mode are working for the USB. The host mode depends on the cpcap-charger driver for VBUS. VBUS and ID pin detection are done using cpcap-adc IIO ADC driver. Cc: devicetree@vger.kernel.org Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> 2017-05-23 07:37:23 +07:00			`#`
			`# Makefile for the phy drivers.`
			`#`

			`obj-$(CONFIG_PHY_CPCAP_USB) += phy-cpcap-usb.o`
phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4 Let's add support for the GPIO controlled USB PHY on the MDM6600 modem. It is used on some Motorola Mapphone series of phones and tablets such as Droid 4. The MDM6600 is hardwired to the first OHCI port in the Droid 4 case, and is controlled by several GPIOs. The USB PHY is integrated into the MDM6600 device it seems. We know this as we get L3 errors from omap-usb-host if trying to use the PHY before MDM6600 is configured. The GPIOs controlling MDM6600 are used to power device on and off, to configure the USB start-up mode (normal mode versus USB flashing), and they also tell the state of the MDM6600 device. The two start-up mode GPIOs are dual-purposed and used for out of band (OOB) wake-up for USB and TS 27.010 serial mux. But we need to configure the USB start-up mode first to get MDM6600 booted in the right mode to be usable in the first place. Note that the Motorola Mapphone Linux kernel tree has a "radio-ctrl" driver for modems. But it really does not control the radio at all, it just controls the modem power and start-up mode for USB. So I came to the conclusion that we're better off having this done in the USB PHY driver. For adding support for USB flashing mode, we can later on add a kernel module option for flash_mode=1 or something similar. Also note that currently there is no PM runtime support for the OHCI on omap variant SoCs. So for low(er) power idle states, currenty both ohci-platform and phy-mapphone-mdm6600 must be unloaded or unbound. For reference here is what I measured for total power consumption on an idle Droid 4 with and without USB related MDM6600 modules: idle lcd off phy-mapphone-mdm6600 ohci-platform 153mW 284mW 344mW So it seems that MDM6600 is currently not yet idling even with it's radio turned off, but that's something that is beyond the control of this USB PHY driver. This patch does get us to the point where modem data and GPS are usable with libqmi and ModemManager for example. Voice calls need more audio driver work. Cc: devicetree@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> 2018-03-09 09:37:50 +07:00			`obj-$(CONFIG_PHY_MAPPHONE_MDM6600) += phy-mapphone-mdm6600.o`