AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-19 22:31:08 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
8bf48e74ea
linux_dsm_epyc7002/arch/arm/boot/dts/imx6qdl-rex.dtsi

353 lines
7.6 KiB
Plaintext
Raw Normal View History

ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
/*
* Copyright 2014 FEDEVEL, Inc.
*
* Author: Robert Nelson <robertcnelson@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
chosen {
stdout-path = &uart1;
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <0>;
reg_3p3v: regulator@0 {
compatible = "regulator-fixed";
reg = <0>;
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
reg_usbh1_vbus: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
pinctrl-names = "default";
regulator-name = "usbh1_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_usb_otg_vbus: regulator@2 {
compatible = "regulator-fixed";
reg = <2>;
pinctrl-names = "default";
regulator-name = "usb_otg_vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_led>;
led0: usr {
label = "usr";
gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "heartbeat";
};
};
sound {
compatible = "fsl,imx6-rex-sgtl5000",
"fsl,imx-audio-sgtl5000";
model = "imx6-rex-sgtl5000";
ssi-controller = <&ssi1>;
audio-codec = <&codec>;
audio-routing =
"MIC_IN", "Mic Jack",
"Mic Jack", "Mic Bias",
"Headphone Jack", "HP_OUT";
mux-int-port = <1>;
mux-ext-port = <3>;
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
};
&ecspi2 {
cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi2>;
status = "okay";
};
&ecspi3 {
cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_ecspi3>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_enet>;
phy-mode = "rgmii";
phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
status = "okay";
};
&hdmi {
ddc-i2c-bus = <&i2c2>;
status = "okay";
};
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
arm: dts: fix unit-address leading 0s Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using the following command: perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*' Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some occurrences of uppercase hex. Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-10-14 00:54:51 +07:00
codec: sgtl5000@a {
ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
compatible = "fsl,sgtl5000";
reg = <0x0a>;
ARM: dts: imx6: Do not hardcode the CLKO clock Using "IMX6QDL_CLK_CKO" for the clock is easier to read instead of the hardcoded clock number. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-04-27 08:28:29 +07:00
clocks = <&clks IMX6QDL_CLK_CKO>;
ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
VDDA-supply = <&reg_3p3v>;
VDDIO-supply = <&reg_3p3v>;
};
};
&i2c2 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
eeprom@57 {
ARM: dts: use 'atmel' as at24 manufacturer for imx6qdl-rex Using 'at' as the <manufacturer> part of the compatible string is now deprecated. Use a correct string: 'atmel,<model>'. Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-01-25 04:31:16 +07:00
compatible = "atmel,24c02";
ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
reg = <0x57>;
};
};
&i2c3 {
clock-frequency = <100000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
};
&iomuxc {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hog>;
imx6qdl-rex {
pinctrl_hog: hoggrp {
fsl,pins = <
/* SGTL5000 sys_mclk */
MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0
>;
};
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
>;
};
pinctrl_ecspi2: ecspi2grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
/* CS */
MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x000b1
>;
};
pinctrl_ecspi3: ecspi3grp {
fsl,pins = <
MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x100b1
MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1
MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x100b1
/* CS */
MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x000b1
>;
};
pinctrl_enet: enetgrp {
fsl,pins = <
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
ARM: dts: imx6qdl: don't configure reserved pad settings Several dts files set a bit in the SPEED field for pads RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there doesn't have an effect and the bit reads as zero. Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-07-09 04:22:54 +07:00
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
ARM: dts: imx6qdl: don't configure reserved pad settings Several dts files set a bit in the SPEED field for pads RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there doesn't have an effect and the bit reads as zero. Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-07-09 04:22:54 +07:00
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
/* Phy reset */
MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x000b0
>;
};
pinctrl_i2c1: i2c1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
>;
};
pinctrl_i2c3: i2c3grp {
fsl,pins = <
MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
>;
};
pinctrl_led: ledgrp {
fsl,pins = <
/* user led */
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
>;
};
pinctrl_usbh1: usbh1grp {
fsl,pins = <
/* power enable, high active */
MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x10b0
>;
};
pinctrl_usbotg: usbotggrp {
fsl,pins = <
MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
/* power enable, high active */
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x10b0
>;
};
pinctrl_usdhc2: usdhc2grp {
fsl,pins = <
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
/* CD */
MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
/* WP */
MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1f0b0
>;
};
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
/* CD */
MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
/* WP */
MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1f0b0
>;
};
};
};
&ssi1 {
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&usbh1 {
vbus-supply = <&reg_usbh1_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1>;
status = "okay";
};
&usbotg {
vbus-supply = <&reg_usb_otg_vbus>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg>;
status = "okay";
};
&usdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc2>;
bus-width = <4>;
cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
dts: imx6: fix sd card gpio polarity specified in device tree cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios should be changed to GPIO_ACTIVE_HIGH. Otherwise, the SD may not work properly due to wrong polarity inversion specified in DT after switch to common parsing function mmc_of_parse(). Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-07-22 19:53:02 +07:00
wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
status = "okay";
};
&usdhc3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc3>;
bus-width = <4>;
cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
dts: imx6: fix sd card gpio polarity specified in device tree cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios should be changed to GPIO_ACTIVE_HIGH. Otherwise, the SD may not work properly due to wrong polarity inversion specified in DT after switch to common parsing function mmc_of_parse(). Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com> Acked-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-07-22 19:53:02 +07:00
wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
ARM: dts: add initial Rex Pro board support Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI, Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-07-08 21:49:22 +07:00
status = "okay";
};
Reference in New Issue Copy Permalink