2012-04-29 21:47:04 +07:00
|
|
|
#
|
|
|
|
# Physical Layer USB driver configuration
|
|
|
|
#
|
2013-06-14 16:51:41 +07:00
|
|
|
menu "USB Physical Layer drivers"
|
2013-06-17 12:45:50 +07:00
|
|
|
|
2013-06-14 16:51:41 +07:00
|
|
|
config USB_PHY
|
|
|
|
def_bool n
|
2012-04-29 21:47:04 +07:00
|
|
|
|
2013-11-26 09:47:53 +07:00
|
|
|
config USB_OTG_FSM
|
|
|
|
bool "USB 2.0 OTG FSM implementation"
|
|
|
|
select USB_OTG
|
|
|
|
select USB_PHY
|
|
|
|
help
|
|
|
|
Implements OTG Final State Machine as specified in On-The-Go
|
|
|
|
and Embedded Host Supplement to the USB Revision 2.0 Specification.
|
|
|
|
|
2013-03-07 16:01:15 +07:00
|
|
|
#
|
|
|
|
# USB Transceiver Drivers
|
|
|
|
#
|
|
|
|
config AB8500_USB
|
|
|
|
tristate "AB8500 USB Transceiver Driver"
|
|
|
|
depends on AB8500_CORE
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
Enable this to support the USB OTG transceiver in AB8500 chip.
|
|
|
|
This transceiver supports high and full speed devices plus,
|
|
|
|
in host mode, low speed.
|
|
|
|
|
|
|
|
config FSL_USB2_OTG
|
|
|
|
bool "Freescale USB OTG Transceiver Driver"
|
2013-11-26 09:47:53 +07:00
|
|
|
depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM_RUNTIME
|
2013-03-07 16:01:15 +07:00
|
|
|
select USB_OTG
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
Enable this to support Freescale USB OTG transceiver.
|
|
|
|
|
|
|
|
config ISP1301_OMAP
|
|
|
|
tristate "Philips ISP1301 with OMAP OTG"
|
|
|
|
depends on I2C && ARCH_OMAP_OTG
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
If you say yes here you get support for the Philips ISP1301
|
|
|
|
USB-On-The-Go transceiver working with the OMAP OTG controller.
|
|
|
|
The ISP1301 is a full speed USB transceiver which is used in
|
|
|
|
products including H2, H3, and H4 development boards for Texas
|
|
|
|
Instruments OMAP processors.
|
|
|
|
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
|
|
will be called isp1301_omap.
|
|
|
|
|
2013-12-13 00:25:30 +07:00
|
|
|
config KEYSTONE_USB_PHY
|
|
|
|
tristate "Keystone USB PHY Driver"
|
|
|
|
depends on ARCH_KEYSTONE || COMPILE_TEST
|
|
|
|
select NOP_USB_XCEIV
|
|
|
|
help
|
|
|
|
Enable this to support Keystone USB phy. This driver provides
|
|
|
|
interface to interact with USB 2.0 and USB 3.0 PHY that is part
|
|
|
|
of the Keystone SOC.
|
|
|
|
|
2013-03-07 16:01:15 +07:00
|
|
|
config MV_U3D_PHY
|
|
|
|
bool "Marvell USB 3.0 PHY controller Driver"
|
2013-03-22 14:15:45 +07:00
|
|
|
depends on CPU_MMP3
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
Enable this to support Marvell USB 3.0 phy controller for Marvell
|
|
|
|
SoC.
|
|
|
|
|
|
|
|
config NOP_USB_XCEIV
|
|
|
|
tristate "NOP USB Transceiver Driver"
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
This driver is to be used by all the usb transceiver which are either
|
|
|
|
built-in with usb ip or which are autonomous and doesn't require any
|
|
|
|
phy programming such as ISP1x04 etc.
|
|
|
|
|
|
|
|
config OMAP_CONTROL_USB
|
|
|
|
tristate "OMAP CONTROL USB Driver"
|
2013-07-04 12:39:10 +07:00
|
|
|
depends on ARCH_OMAP2PLUS || COMPILE_TEST
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
Enable this to add support for the USB part present in the control
|
|
|
|
module. This driver has API to power on the USB2 PHY and to write to
|
|
|
|
the mailbox. The mailbox is present only in omap4 and the register to
|
|
|
|
power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
|
|
|
|
additional register to power on USB3 PHY.
|
2012-04-29 21:47:04 +07:00
|
|
|
|
2013-01-25 09:51:48 +07:00
|
|
|
config OMAP_USB3
|
|
|
|
tristate "OMAP USB3 PHY Driver"
|
2013-07-04 12:39:10 +07:00
|
|
|
depends on ARCH_OMAP2PLUS || COMPILE_TEST
|
2013-01-25 09:51:48 +07:00
|
|
|
select OMAP_CONTROL_USB
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-01-25 09:51:48 +07:00
|
|
|
help
|
|
|
|
Enable this to support the USB3 PHY that is part of SOC. This
|
|
|
|
driver takes care of all the PHY functionality apart from comparator.
|
|
|
|
This driver interacts with the "OMAP Control USB Driver" to power
|
|
|
|
on/off the PHY.
|
|
|
|
|
2013-07-31 02:43:45 +07:00
|
|
|
config AM335X_CONTROL_USB
|
|
|
|
tristate
|
|
|
|
|
|
|
|
config AM335X_PHY_USB
|
|
|
|
tristate "AM335x USB PHY Driver"
|
2013-09-04 04:35:52 +07:00
|
|
|
depends on ARM || COMPILE_TEST
|
2013-07-31 02:43:45 +07:00
|
|
|
select USB_PHY
|
|
|
|
select AM335X_CONTROL_USB
|
|
|
|
select NOP_USB_XCEIV
|
|
|
|
help
|
|
|
|
This driver provides PHY support for that phy which part for the
|
|
|
|
AM335x SoC.
|
|
|
|
|
2013-03-07 16:01:15 +07:00
|
|
|
config SAMSUNG_USBPHY
|
2013-05-16 16:57:06 +07:00
|
|
|
tristate
|
2013-01-25 17:23:57 +07:00
|
|
|
help
|
2013-03-14 17:29:10 +07:00
|
|
|
Enable this to support Samsung USB phy helper driver for Samsung SoCs.
|
|
|
|
This driver provides common interface to interact, for Samsung USB 2.0 PHY
|
|
|
|
driver and later for Samsung USB 3.0 PHY driver.
|
|
|
|
|
|
|
|
config SAMSUNG_USB2PHY
|
|
|
|
tristate "Samsung USB 2.0 PHY controller Driver"
|
|
|
|
select SAMSUNG_USBPHY
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-14 17:29:10 +07:00
|
|
|
help
|
|
|
|
Enable this to support Samsung USB 2.0 (High Speed) PHY controller
|
|
|
|
driver for Samsung SoCs.
|
2013-03-07 16:01:15 +07:00
|
|
|
|
2013-03-14 17:29:11 +07:00
|
|
|
config SAMSUNG_USB3PHY
|
|
|
|
tristate "Samsung USB 3.0 PHY controller Driver"
|
|
|
|
select SAMSUNG_USBPHY
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-14 17:29:11 +07:00
|
|
|
help
|
|
|
|
Enable this to support Samsung USB 3.0 (Super Speed) phy controller
|
|
|
|
for samsung SoCs.
|
|
|
|
|
2013-03-07 16:01:15 +07:00
|
|
|
config TWL6030_USB
|
|
|
|
tristate "TWL6030 USB Transceiver Driver"
|
|
|
|
depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
|
|
|
|
help
|
|
|
|
Enable this to support the USB OTG transceiver on TWL6030
|
|
|
|
family chips. This TWL6030 transceiver has the VBUS and ID GND
|
|
|
|
and OTG SRP events capabilities. For all other transceiver functionality
|
|
|
|
UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
|
|
|
|
are hooked to this driver through platform_data structure.
|
|
|
|
The definition of internal PHY APIs are in the mach-omap2 layer.
|
|
|
|
|
|
|
|
config USB_GPIO_VBUS
|
|
|
|
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
|
2013-05-09 23:59:16 +07:00
|
|
|
depends on GPIOLIB
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
Provides simple GPIO VBUS sensing for controllers with an
|
|
|
|
internal transceiver via the usb_phy interface, and
|
|
|
|
optionally control of a D+ pullup GPIO as well as a VBUS
|
|
|
|
current limit regulator.
|
2013-01-25 17:23:57 +07:00
|
|
|
|
2013-12-06 21:13:06 +07:00
|
|
|
config OMAP_OTG
|
|
|
|
tristate "OMAP USB OTG controller driver"
|
|
|
|
depends on ARCH_OMAP_OTG && EXTCON
|
|
|
|
help
|
|
|
|
Enable this to support some transceivers on OMAP1 platforms. OTG
|
|
|
|
controller is needed to switch between host and peripheral modes.
|
|
|
|
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
|
|
will be called omap-otg.
|
|
|
|
|
2013-12-06 21:13:07 +07:00
|
|
|
config TAHVO_USB
|
|
|
|
tristate "Tahvo USB transceiver driver"
|
|
|
|
depends on MFD_RETU && EXTCON
|
|
|
|
select USB_PHY
|
|
|
|
help
|
|
|
|
Enable this to support USB transceiver on Tahvo. This is used
|
|
|
|
at least on Nokia 770.
|
|
|
|
|
|
|
|
config TAHVO_USB_HOST_BY_DEFAULT
|
|
|
|
depends on TAHVO_USB
|
|
|
|
boolean "Device in USB host mode by default"
|
|
|
|
help
|
|
|
|
Say Y here, if you want the device to enter USB host mode
|
|
|
|
by default on bootup.
|
|
|
|
|
2012-04-29 21:47:04 +07:00
|
|
|
config USB_ISP1301
|
|
|
|
tristate "NXP ISP1301 USB transceiver support"
|
2012-06-26 21:56:48 +07:00
|
|
|
depends on USB || USB_GADGET
|
2012-04-29 21:47:04 +07:00
|
|
|
depends on I2C
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2012-04-29 21:47:04 +07:00
|
|
|
help
|
|
|
|
Say Y here to add support for the NXP ISP1301 USB transceiver driver.
|
|
|
|
This chip is typically used as USB transceiver for USB host, gadget
|
|
|
|
and OTG drivers (to be selected separately).
|
|
|
|
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
|
|
module will be called isp1301.
|
2012-08-09 21:29:31 +07:00
|
|
|
|
2013-03-07 16:01:15 +07:00
|
|
|
config USB_MSM_OTG
|
|
|
|
tristate "OTG support for Qualcomm on-chip USB controller"
|
|
|
|
depends on (USB || USB_GADGET) && ARCH_MSM
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2012-08-09 21:29:31 +07:00
|
|
|
help
|
2013-03-07 16:01:15 +07:00
|
|
|
Enable this to support the USB OTG transceiver on MSM chips. It
|
|
|
|
handles PHY initialization, clock management, and workarounds
|
|
|
|
required after resetting the hardware and power management.
|
|
|
|
This driver is required even for peripheral only or host only
|
|
|
|
mode configurations.
|
|
|
|
This driver is not supported on boards like trout which
|
|
|
|
has an external PHY.
|
|
|
|
|
|
|
|
config USB_MV_OTG
|
|
|
|
tristate "Marvell USB OTG support"
|
2013-05-01 23:13:54 +07:00
|
|
|
depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME
|
2013-03-07 16:01:15 +07:00
|
|
|
select USB_OTG
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
Say Y here if you want to build Marvell USB OTG transciever
|
|
|
|
driver in kernel (including PXA and MMP series). This driver
|
|
|
|
implements role switch between EHCI host driver and gadget driver.
|
|
|
|
|
|
|
|
To compile this driver as a module, choose M here.
|
|
|
|
|
|
|
|
config USB_MXS_PHY
|
|
|
|
tristate "Freescale MXS USB PHY support"
|
|
|
|
depends on ARCH_MXC || ARCH_MXS
|
|
|
|
select STMP_DEVICE
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2013-03-07 16:01:15 +07:00
|
|
|
help
|
|
|
|
Enable this to support the Freescale MXS USB PHY.
|
|
|
|
|
|
|
|
MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
|
2012-11-01 09:03:11 +07:00
|
|
|
|
|
|
|
config USB_RCAR_PHY
|
2013-06-09 03:34:36 +07:00
|
|
|
tristate "Renesas R-Car USB PHY support"
|
2012-11-01 09:03:11 +07:00
|
|
|
depends on USB || USB_GADGET
|
2013-06-14 16:51:41 +07:00
|
|
|
select USB_PHY
|
2012-11-01 09:03:11 +07:00
|
|
|
help
|
2013-06-09 03:34:36 +07:00
|
|
|
Say Y here to add support for the Renesas R-Car USB common PHY driver.
|
|
|
|
This chip is typically used as USB PHY for USB host, gadget.
|
|
|
|
This driver supports R8A7778 and R8A7779.
|
2012-11-01 09:03:11 +07:00
|
|
|
|
|
|
|
To compile this driver as a module, choose M here: the
|
2013-06-09 03:34:36 +07:00
|
|
|
module will be called phy-rcar-usb.
|
2012-11-23 17:33:06 +07:00
|
|
|
|
2013-10-10 23:35:17 +07:00
|
|
|
config USB_RCAR_GEN2_PHY
|
|
|
|
tristate "Renesas R-Car Gen2 USB PHY support"
|
|
|
|
depends on ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST
|
|
|
|
select USB_PHY
|
|
|
|
help
|
|
|
|
Say Y here to add support for the Renesas R-Car Gen2 USB PHY driver.
|
|
|
|
It is typically used to control internal USB PHY for USBHS,
|
|
|
|
and to configure shared USB channels 0 and 2.
|
|
|
|
This driver supports R8A7790 and R8A7791.
|
|
|
|
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
|
|
module will be called phy-rcar-gen2-usb.
|
|
|
|
|
2013-03-07 16:01:15 +07:00
|
|
|
config USB_ULPI
|
|
|
|
bool "Generic ULPI Transceiver Driver"
|
|
|
|
depends on ARM
|
2012-11-23 17:33:06 +07:00
|
|
|
help
|
2013-03-07 16:01:15 +07:00
|
|
|
Enable this to support ULPI connected USB OTG transceivers which
|
|
|
|
are likely found on embedded boards.
|
|
|
|
|
|
|
|
config USB_ULPI_VIEWPORT
|
|
|
|
bool
|
|
|
|
depends on USB_ULPI
|
2012-11-23 17:33:06 +07:00
|
|
|
help
|
2013-03-07 16:01:15 +07:00
|
|
|
Provides read/write operations to the ULPI phy register set for
|
|
|
|
controllers with a viewport register (e.g. Chipidea/ARC controllers).
|
|
|
|
|
2013-06-14 16:51:41 +07:00
|
|
|
endmenu
|