AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-24 00:22:07 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
6f5a272c99
linux_dsm_epyc7002/drivers/net/dsa/mv88e6xxx.h

119 lines
3.8 KiB
C
Raw Normal View History

net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
/*
* net/dsa/mv88e6xxx.h - Marvell 88e6xxx switch chip support
* Copyright (c) 2008 Marvell Semiconductor
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef __MV88E6XXX_H
#define __MV88E6XXX_H
#define REG_PORT(p) (0x10 + (p))
#define REG_GLOBAL 0x1b
#define REG_GLOBAL2 0x1c
struct mv88e6xxx_priv_state {
DSA: Convert DSA comments to network-style comments Convert DSA driver comments to network-style comments as reported by checkpatch.pl. Fix spelling error. Signed-off-by: Barry Grussling <barry@grussling.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-08 23:05:53 +07:00
/* When using multi-chip addressing, this mutex protects
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
* access to the indirect access registers. (In single-chip
* mode, this mutex is effectively useless.)
*/
struct mutex smi_mutex;
dsa: add support for the Marvell 88E6131 switch chip Add support for the Marvell 88E6131 switch chip. This chip only supports the original (ethertype-less) DSA tagging format. On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive access to each of the PHYs's MII management registers. If we want to talk to the PHYs from software, we have to disable the PPU and wait for it to complete its current transaction before we can do so, and we need to re-enable the PPU afterwards to make sure that the switch will notice changes in link state and speed on the individual ports as they occur. Since disabling the PPU is rather slow, and since MII management accesses are typically done in bursts, this patch keeps the PPU disabled for 10ms after a software access completes. This makes handling the PPU slightly more complex, but speeds up something like running ethtool on one of the switch slave interfaces from ~300ms to ~30ms on typical hardware. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:45:18 +07:00
#ifdef CONFIG_NET_DSA_MV88E6XXX_NEED_PPU
DSA: Convert DSA comments to network-style comments Convert DSA driver comments to network-style comments as reported by checkpatch.pl. Fix spelling error. Signed-off-by: Barry Grussling <barry@grussling.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-08 23:05:53 +07:00
/* Handles automatic disabling and re-enabling of the PHY
dsa: add support for the Marvell 88E6131 switch chip Add support for the Marvell 88E6131 switch chip. This chip only supports the original (ethertype-less) DSA tagging format. On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive access to each of the PHYs's MII management registers. If we want to talk to the PHYs from software, we have to disable the PPU and wait for it to complete its current transaction before we can do so, and we need to re-enable the PPU afterwards to make sure that the switch will notice changes in link state and speed on the individual ports as they occur. Since disabling the PPU is rather slow, and since MII management accesses are typically done in bursts, this patch keeps the PPU disabled for 10ms after a software access completes. This makes handling the PPU slightly more complex, but speeds up something like running ethtool on one of the switch slave interfaces from ~300ms to ~30ms on typical hardware. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:45:18 +07:00
* polling unit.
*/
struct mutex ppu_mutex;
int ppu_disabled;
struct work_struct ppu_work;
struct timer_list ppu_timer;
#endif
DSA: Convert DSA comments to network-style comments Convert DSA driver comments to network-style comments as reported by checkpatch.pl. Fix spelling error. Signed-off-by: Barry Grussling <barry@grussling.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-08 23:05:53 +07:00
/* This mutex serialises access to the statistics unit.
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
* Hold this mutex over snapshot + dump sequences.
*/
struct mutex stats_mutex;
dsa/mv88e6131: add support for mv88e6085 switch The mv88e6085 is identical to the mv88e6095, except that all ports are 10/100 Mb/s, so use the existing setup code except for the cpu/dsa speed selection in _setup_port(). Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-05 10:03:56 +07:00
net: dsa: Add support for Marvell 88E6352 Marvell 88E6352 is mostly compatible to MV88E6123/61/65, but requires indirect phy access. Also, its configuration registers are a bit different. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 00:44:56 +07:00
/* This mutex serializes phy access for chips with
* indirect phy addressing. It is unused for chips
* with direct phy access.
*/
struct mutex phy_mutex;
net: dsa/mv88e6352: Implement EEPROM access functions MV88E6352 supports read and write access to its configuration eeprom. There is no means to detect if an EEPROM is connected to the switch. Also, the switch supports EEPROMs with different sizes, but can not detect or report the type or size of connected EEPROMs. Therefore, do not implement the get_eeprom_len callback but depend on platform or devicetree data to provide information about EEPROM presence and size. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 00:45:03 +07:00
/* This mutex serializes eeprom access for chips with
* eeprom support.
*/
struct mutex eeprom_mutex;
dsa/mv88e6131: add support for mv88e6085 switch The mv88e6085 is identical to the mv88e6095, except that all ports are 10/100 Mb/s, so use the existing setup code except for the cpu/dsa speed selection in _setup_port(). Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-05 10:03:56 +07:00
int id; /* switch product id */
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
};
struct mv88e6xxx_hw_stat {
char string[ETH_GSTRING_LEN];
int sizeof_stat;
int reg;
};
int __mv88e6xxx_reg_read(struct mii_bus *bus, int sw_addr, int addr, int reg);
int mv88e6xxx_reg_read(struct dsa_switch *ds, int addr, int reg);
int __mv88e6xxx_reg_write(struct mii_bus *bus, int sw_addr, int addr,
DSA: Convert spaces to tabs where appropriate Fix DSA whitespace issues reported by checkpatch.pl Signed-off-by: Barry Grussling <barry@grussling.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-08 23:05:56 +07:00
int reg, u16 val);
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
int mv88e6xxx_reg_write(struct dsa_switch *ds, int addr, int reg, u16 val);
int mv88e6xxx_config_prio(struct dsa_switch *ds);
dsa: add support for the Marvell 88E6131 switch chip Add support for the Marvell 88E6131 switch chip. This chip only supports the original (ethertype-less) DSA tagging format. On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive access to each of the PHYs's MII management registers. If we want to talk to the PHYs from software, we have to disable the PPU and wait for it to complete its current transaction before we can do so, and we need to re-enable the PPU afterwards to make sure that the switch will notice changes in link state and speed on the individual ports as they occur. Since disabling the PPU is rather slow, and since MII management accesses are typically done in bursts, this patch keeps the PPU disabled for 10ms after a software access completes. This makes handling the PPU slightly more complex, but speeds up something like running ethtool on one of the switch slave interfaces from ~300ms to ~30ms on typical hardware. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:45:18 +07:00
int mv88e6xxx_set_addr_direct(struct dsa_switch *ds, u8 *addr);
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
int mv88e6xxx_set_addr_indirect(struct dsa_switch *ds, u8 *addr);
int mv88e6xxx_phy_read(struct dsa_switch *ds, int addr, int regnum);
int mv88e6xxx_phy_write(struct dsa_switch *ds, int addr, int regnum, u16 val);
dsa: add support for the Marvell 88E6131 switch chip Add support for the Marvell 88E6131 switch chip. This chip only supports the original (ethertype-less) DSA tagging format. On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive access to each of the PHYs's MII management registers. If we want to talk to the PHYs from software, we have to disable the PPU and wait for it to complete its current transaction before we can do so, and we need to re-enable the PPU afterwards to make sure that the switch will notice changes in link state and speed on the individual ports as they occur. Since disabling the PPU is rather slow, and since MII management accesses are typically done in bursts, this patch keeps the PPU disabled for 10ms after a software access completes. This makes handling the PPU slightly more complex, but speeds up something like running ethtool on one of the switch slave interfaces from ~300ms to ~30ms on typical hardware. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:45:18 +07:00
void mv88e6xxx_ppu_state_init(struct dsa_switch *ds);
int mv88e6xxx_phy_read_ppu(struct dsa_switch *ds, int addr, int regnum);
int mv88e6xxx_phy_write_ppu(struct dsa_switch *ds, int addr,
int regnum, u16 val);
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
void mv88e6xxx_poll_link(struct dsa_switch *ds);
void mv88e6xxx_get_strings(struct dsa_switch *ds,
int nr_stats, struct mv88e6xxx_hw_stat *stats,
int port, uint8_t *data);
void mv88e6xxx_get_ethtool_stats(struct dsa_switch *ds,
int nr_stats, struct mv88e6xxx_hw_stat *stats,
int port, uint64_t *data);
net: dsa/mv88e6123_61_65: Add support for reading switch registers The infrastructure can now report switch registers to ethtool. Add support for it to the mv88e6123_61_65 driver. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 00:45:05 +07:00
int mv88e6xxx_get_regs_len(struct dsa_switch *ds, int port);
void mv88e6xxx_get_regs(struct dsa_switch *ds, int port,
struct ethtool_regs *regs, void *_p);
net: dsa: Centralise code for reading the temperature sensor The method to read the temperature used in the mve6123_61_65 driver can also be used for other chips. Move the code into the shared code base of mv88e6xxx.c. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-16 04:24:51 +07:00
int mv88e6xxx_get_temp(struct dsa_switch *ds, int *temp);
net: dsa: mv88e6352: Refactor shareable code The mv88e6352 allows access to the port phys via an internal mdio bus which is accessed using registers in the GLOBAL 2 range. The mv88e6171 and probably other devices use the same mechanism. Move this code into the shared mv88e6xxx.c library. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-15 01:17:50 +07:00
int mv88e6xxx_phy_wait(struct dsa_switch *ds);
int mv88e6xxx_eeprom_load_wait(struct dsa_switch *ds);
int mv88e6xxx_eeprom_busy_wait(struct dsa_switch *ds);
int mv88e6xxx_phy_read_indirect(struct dsa_switch *ds, int addr, int regnum);
int mv88e6xxx_phy_write_indirect(struct dsa_switch *ds, int addr, int regnum,
u16 val);
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
mv88e6xxx: Combine mv88e6131 and mv88e612_61_65 drivers These drivers share a lot of code, so if we make them modular they should be built into the same module. Therefore, link them together and merge their respective module init and exit functions. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-25 21:36:19 +07:00
extern struct dsa_switch_driver mv88e6131_switch_driver;
extern struct dsa_switch_driver mv88e6123_61_65_switch_driver;
net: dsa: Add support for Marvell 88E6352 Marvell 88E6352 is mostly compatible to MV88E6123/61/65, but requires indirect phy access. Also, its configuration registers are a bit different. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-30 00:44:56 +07:00
extern struct dsa_switch_driver mv88e6352_switch_driver;
net: DSA: Marvell mv88e6171 switch driver This is the Marvell driver with some cleanups by Claudio Leite and myself. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Cc: Claudio Leite <leitec@staticky.com> Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13 04:58:44 +07:00
extern struct dsa_switch_driver mv88e6171_switch_driver;
mv88e6xxx: Combine mv88e6131 and mv88e612_61_65 drivers These drivers share a lot of code, so if we make them modular they should be built into the same module. Therefore, link them together and merge their respective module init and exit functions. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-25 21:36:19 +07:00
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 20:44:02 +07:00
#define REG_READ(addr, reg) \
({ \
int __ret; \
\
__ret = mv88e6xxx_reg_read(ds, addr, reg); \
if (__ret < 0) \
return __ret; \
__ret; \
})
#define REG_WRITE(addr, reg, val) \
({ \
int __ret; \
\
__ret = mv88e6xxx_reg_write(ds, addr, reg, val); \
if (__ret < 0) \
return __ret; \
})
#endif
Reference in New Issue Copy Permalink