linux_dsm_epyc7002/drivers/net/ipvlan/ipvlan.h

211 lines
5.4 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0-or-later */
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
/*
* Copyright (c) 2014 Mahesh Bandewar <maheshb@google.com>
*/
#ifndef __IPVLAN_H
#define __IPVLAN_H
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/rculist.h>
#include <linux/notifier.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/if_arp.h>
#include <linux/if_link.h>
#include <linux/if_vlan.h>
#include <linux/ip.h>
#include <linux/inetdevice.h>
#include <linux/netfilter.h>
#include <net/ip.h>
#include <net/ip6_route.h>
#include <net/netns/generic.h>
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
#include <net/rtnetlink.h>
#include <net/route.h>
#include <net/addrconf.h>
#include <net/l3mdev.h>
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
#define IPVLAN_DRV "ipvlan"
#define IPV_DRV_VER "0.1"
#define IPVLAN_HASH_SIZE (1 << BITS_PER_BYTE)
#define IPVLAN_HASH_MASK (IPVLAN_HASH_SIZE - 1)
#define IPVLAN_MAC_FILTER_BITS 8
#define IPVLAN_MAC_FILTER_SIZE (1 << IPVLAN_MAC_FILTER_BITS)
#define IPVLAN_MAC_FILTER_MASK (IPVLAN_MAC_FILTER_SIZE - 1)
#define IPVLAN_QBACKLOG_LIMIT 1000
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
typedef enum {
IPVL_IPV6 = 0,
IPVL_ICMPV6,
IPVL_IPV4,
IPVL_ARP,
} ipvl_hdr_type;
struct ipvl_pcpu_stats {
u64 rx_pkts;
u64 rx_bytes;
u64 rx_mcast;
u64 tx_pkts;
u64 tx_bytes;
struct u64_stats_sync syncp;
u32 rx_errs;
u32 tx_drps;
};
struct ipvl_port;
struct ipvl_dev {
struct net_device *dev;
struct list_head pnode;
struct ipvl_port *port;
struct net_device *phy_dev;
struct list_head addrs;
struct ipvl_pcpu_stats __percpu *pcpu_stats;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
DECLARE_BITMAP(mac_filters, IPVLAN_MAC_FILTER_SIZE);
netdev_features_t sfeatures;
u32 msg_enable;
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
spinlock_t addrs_lock;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
};
struct ipvl_addr {
struct ipvl_dev *master; /* Back pointer to master */
union {
struct in6_addr ip6; /* IPv6 address on logical interface */
struct in_addr ip4; /* IPv4 address on logical interface */
} ipu;
#define ip6addr ipu.ip6
#define ip4addr ipu.ip4
struct hlist_node hlnode; /* Hash-table linkage */
struct list_head anode; /* logical-interface linkage */
ipvl_hdr_type atype;
struct rcu_head rcu;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
};
struct ipvl_port {
struct net_device *dev;
possible_net_t pnet;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
struct hlist_head hlhead[IPVLAN_HASH_SIZE];
struct list_head ipvlans;
u16 mode;
u16 flags;
u16 dev_id_start;
struct work_struct wq;
struct sk_buff_head backlog;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
int count;
struct ida ida;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
};
ipvlan: fix multicast processing In an IPvlan setup when master is set in loopback mode e.g. ethtool -K eth0 set loopback on where eth0 is master device for IPvlan setup. The failure is caused by the faulty logic that determines if the packet is from TX-path vs. RX-path by just looking at the mac- addresses on the packet while processing multicast packets. In the loopback-mode where this crash was happening, the packets that are sent out are reflected by the NIC and are processed on the RX path, but mac-address check tricks into thinking this packet is from TX path and falsely uses dev_forward_skb() to pass packets to the slave (virtual) devices. This patch records the path while queueing packets and eliminates logic of looking at mac-addresses for the same decision. ------------[ cut here ]------------ kernel BUG at include/linux/skbuff.h:1737! Call Trace: [<ffffffff921fbbc2>] dev_forward_skb+0x92/0xd0 [<ffffffffc031ac65>] ipvlan_process_multicast+0x395/0x4c0 [ipvlan] [<ffffffffc031a9a7>] ? ipvlan_process_multicast+0xd7/0x4c0 [ipvlan] [<ffffffff91cdfea7>] ? process_one_work+0x147/0x660 [<ffffffff91cdff09>] process_one_work+0x1a9/0x660 [<ffffffff91cdfea7>] ? process_one_work+0x147/0x660 [<ffffffff91ce086d>] worker_thread+0x11d/0x360 [<ffffffff91ce0750>] ? rescuer_thread+0x350/0x350 [<ffffffff91ce960b>] kthread+0xdb/0xe0 [<ffffffff91c05c70>] ? _raw_spin_unlock_irq+0x30/0x50 [<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0 [<ffffffff92348b7a>] ret_from_fork+0x9a/0xd0 [<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0 Fixes: ba35f8588f47 ("ipvlan: Defer multicast / broadcast processing to a work-queue") Signed-off-by: Mahesh Bandewar <maheshb@google.com> CC: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-12-22 08:30:16 +07:00
struct ipvl_skb_cb {
bool tx_pkt;
};
#define IPVL_SKB_CB(_skb) ((struct ipvl_skb_cb *)&((_skb)->cb[0]))
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static inline struct ipvl_port *ipvlan_port_get_rcu(const struct net_device *d)
{
return rcu_dereference(d->rx_handler_data);
}
ipvlan: use rcu_deference_bh() in ipvlan_queue_xmit() In tx path rcu_read_lock_bh() is held, so we need rcu_deference_bh(). This fixes the following warning: =============================== [ INFO: suspicious RCU usage. ] 4.1.0-rc1+ #1007 Not tainted ------------------------------- drivers/net/ipvlan/ipvlan.h:106 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 0 1 lock held by dhclient/1076: #0: (rcu_read_lock_bh){......}, at: [<ffffffff817e8d84>] rcu_lock_acquire+0x0/0x26 stack backtrace: CPU: 2 PID: 1076 Comm: dhclient Not tainted 4.1.0-rc1+ #1007 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 0000000000000001 ffff8800d381bac8 ffffffff81a4154f 000000003c1a3c19 ffff8800d4d0a690 ffff8800d381baf8 ffffffff810b849f ffff880117d41148 ffff880117d40000 ffff880117d40068 0000000000000156 ffff8800d381bb18 Call Trace: [<ffffffff81a4154f>] dump_stack+0x4c/0x65 [<ffffffff810b849f>] lockdep_rcu_suspicious+0x107/0x110 [<ffffffff8165a522>] ipvlan_port_get_rcu+0x47/0x4e [<ffffffff8165ad14>] ipvlan_queue_xmit+0x35/0x450 [<ffffffff817ea45d>] ? rcu_read_unlock+0x3e/0x5f [<ffffffff810a20bf>] ? local_clock+0x19/0x22 [<ffffffff810b4781>] ? __lock_is_held+0x39/0x52 [<ffffffff8165b64c>] ipvlan_start_xmit+0x1b/0x44 [<ffffffff817edf7f>] dev_hard_start_xmit+0x2ae/0x467 [<ffffffff817ee642>] __dev_queue_xmit+0x50a/0x60c [<ffffffff817ee7a7>] dev_queue_xmit_sk+0x13/0x15 [<ffffffff81997596>] dev_queue_xmit+0x10/0x12 [<ffffffff8199b41c>] packet_sendmsg+0xb6b/0xbdf [<ffffffff810b5ea7>] ? mark_lock+0x2e/0x226 [<ffffffff810a1fcc>] ? sched_clock_cpu+0x9e/0xb7 [<ffffffff817d56f9>] sock_sendmsg_nosec+0x12/0x1d [<ffffffff817d7257>] sock_sendmsg+0x29/0x2e [<ffffffff817d72cc>] sock_write_iter+0x70/0x91 [<ffffffff81199563>] __vfs_write+0x7e/0xa7 [<ffffffff811996bc>] vfs_write+0x92/0xe8 [<ffffffff811997d7>] SyS_write+0x47/0x7e [<ffffffff81a4d517>] system_call_fastpath+0x12/0x6f Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.") Cc: Mahesh Bandewar <maheshb@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-14 20:35:54 +07:00
static inline struct ipvl_port *ipvlan_port_get_rcu_bh(const struct net_device *d)
{
return rcu_dereference_bh(d->rx_handler_data);
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static inline struct ipvl_port *ipvlan_port_get_rtnl(const struct net_device *d)
{
return rtnl_dereference(d->rx_handler_data);
}
static inline bool ipvlan_is_private(const struct ipvl_port *port)
{
return !!(port->flags & IPVLAN_F_PRIVATE);
}
static inline void ipvlan_mark_private(struct ipvl_port *port)
{
port->flags |= IPVLAN_F_PRIVATE;
}
static inline void ipvlan_clear_private(struct ipvl_port *port)
{
port->flags &= ~IPVLAN_F_PRIVATE;
}
static inline bool ipvlan_is_vepa(const struct ipvl_port *port)
{
return !!(port->flags & IPVLAN_F_VEPA);
}
static inline void ipvlan_mark_vepa(struct ipvl_port *port)
{
port->flags |= IPVLAN_F_VEPA;
}
static inline void ipvlan_clear_vepa(struct ipvl_port *port)
{
port->flags &= ~IPVLAN_F_VEPA;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
void ipvlan_init_secret(void);
unsigned int ipvlan_mac_hash(const unsigned char *addr);
rx_handler_result_t ipvlan_handle_frame(struct sk_buff **pskb);
void ipvlan_process_multicast(struct work_struct *work);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
int ipvlan_queue_xmit(struct sk_buff *skb, struct net_device *dev);
void ipvlan_ht_addr_add(struct ipvl_dev *ipvlan, struct ipvl_addr *addr);
struct ipvl_addr *ipvlan_find_addr(const struct ipvl_dev *ipvlan,
const void *iaddr, bool is_v6);
bool ipvlan_addr_busy(struct ipvl_port *port, void *iaddr, bool is_v6);
void ipvlan_ht_addr_del(struct ipvl_addr *addr);
struct ipvl_addr *ipvlan_addr_lookup(struct ipvl_port *port, void *lyr3h,
int addr_type, bool use_dest);
void *ipvlan_get_L3_hdr(struct ipvl_port *port, struct sk_buff *skb, int *type);
void ipvlan_count_rx(const struct ipvl_dev *ipvlan,
unsigned int len, bool success, bool mcast);
int ipvlan_link_new(struct net *src_net, struct net_device *dev,
struct nlattr *tb[], struct nlattr *data[],
struct netlink_ext_ack *extack);
void ipvlan_link_delete(struct net_device *dev, struct list_head *head);
void ipvlan_link_setup(struct net_device *dev);
int ipvlan_link_register(struct rtnl_link_ops *ops);
#ifdef CONFIG_IPVLAN_L3S
int ipvlan_l3s_register(struct ipvl_port *port);
void ipvlan_l3s_unregister(struct ipvl_port *port);
void ipvlan_migrate_l3s_hook(struct net *oldnet, struct net *newnet);
int ipvlan_l3s_init(void);
void ipvlan_l3s_cleanup(void);
#else
static inline int ipvlan_l3s_register(struct ipvl_port *port)
{
return -ENOTSUPP;
}
static inline void ipvlan_l3s_unregister(struct ipvl_port *port)
{
}
static inline void ipvlan_migrate_l3s_hook(struct net *oldnet,
struct net *newnet)
{
}
static inline int ipvlan_l3s_init(void)
{
return 0;
}
static inline void ipvlan_l3s_cleanup(void)
{
}
#endif /* CONFIG_IPVLAN_L3S */
static inline bool netif_is_ipvlan_port(const struct net_device *dev)
{
return rcu_access_pointer(dev->rx_handler) == ipvlan_handle_frame;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
#endif /* __IPVLAN_H */