AuxXxilium/linux_dsm_epyc7002
1
0
Fork 0
mirror of https://github.com/AuxXxilium/linux_dsm_epyc7002.git synced 2024-12-28 05:45:09 +07:00
Code Issues Actions Packages Projects Releases Wiki Activity
5c2cebda43
linux_dsm_epyc7002/drivers/net/ethernet/marvell/Makefile

11 lines
256 B
Makefile
Raw Normal View History

skge/sky2/mv643xx/pxa168: Move the Marvell Ethernet drivers Move the Marvell Ethernet drivers into drivers/net/ethernet/marvell/ and make the necessary Kconfig and Makefile changes. CC: Sachin Sanap <ssanap@marvell.com> CC: Zhangfei Gao <zgao6@marvell.com> CC: Philip Rakity <prakity@marvell.com> CC: Mark Brown <markb@marvell.com> CC: Lennert Buytenhek <buytenh@marvell.com> CC: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-05-21 10:18:55 +07:00
#
# Makefile for the Marvell device drivers.
#
net: mvmdio: new Marvell MDIO driver This patch adds a separate driver for the MDIO interface of the Marvell Ethernet controllers. There are two reasons to have a separate driver rather than including it inside the MAC driver itself: *) The MDIO interface is shared by all Ethernet ports, so a driver must guarantee non-concurrent accesses to this MDIO interface. The most logical way is to have a separate driver that handles this single MDIO interface, used by all Ethernet ports. *) The MDIO interface is the same between the existing mv643xx_eth driver and the new mvneta driver. Even though it is for now only used by the mvneta driver, it will in the future be used by the mv643xx_eth driver as well. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-11-12 23:03:47 +07:00
obj-$(CONFIG_MVMDIO) += mvmdio.o
mv643xx_eth: convert to use the Marvell Orion MDIO driver This patch converts the Marvell MV643XX ethernet driver to use the Marvell Orion MDIO driver. As a result, PowerPC and ARM platforms registering the Marvell MV643XX ethernet driver are also updated to register a Marvell Orion MDIO driver. This driver voluntarily overlaps with the Marvell Ethernet shared registers because it will use a subset of this shared register (shared_base + 0x4 to shared_base + 0x84). The Ethernet driver is also updated to look up for a PHY device using the Orion MDIO bus driver. For ARM and PowerPC we register a single instance of the "mvmdio" driver in the system like it used to be done with the use of the "shared_smi" platform_data cookie on ARM. Note that it is safe to register the mvmdio driver only for the "ge00" instance of the driver because this "ge00" interface is guaranteed to always be explicitely registered by consumers of arch/arm/plat-orion/common.c and other instances (ge01, ge10 and ge11) were all pointing their shared_smi to ge00. For PowerPC the in-tree Device Tree Source files mention only one MV643XX ethernet MAC instance so the MDIO bus driver is registered only when id == 0. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-22 10:39:28 +07:00
obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
net: mvneta: driver for Marvell Armada 370/XP network unit This patch contains a new network driver for the network unit of the ARM Marvell Armada 370 and the Armada XP. Both SoCs use the PJ4B processor, a Marvell-developed ARM core that implements the ARMv7 instruction set. Compared to previous ARM Marvell SoCs (Kirkwood, Orion, Discovery), the network unit in Armada 370 and Armada XP is highly different. This is the reason why this new 'mvneta' driver is needed, while the older ARM Marvell SoCs use the 'mv643xx_eth' driver. Here is an overview of the most important hardware changes that require a new, specific, driver for the network unit of Armada 370/XP: - The new network unit has a completely different design and layout for the RX and TX descriptors. They are now organized as a simple array (each RX and TX queue has base address and size of this array) rather than a linked list as in the old SoCs. - The new network unit has a different RXQ and TXQ management: this management is done using special read/write counter registers, while in the Old SocS, it was done using the Ownership bit in RX and TX descriptors. - The new network unit has different interrupt registers - The new network unit way of cleaning of interrupts is not done by writing to the cause register, but by updating per-queue counters - The new network unit has different GMAC registers (link, speed, duplex configuration) and different WRR registers. - The new network unit has lots of new units like PnC (Parser and Classifier), PMT, BM (Memory Buffer Management), xPON, and more. The driver proposed in the current patch only handles the basic features. Additional hardware features will progressively be supported as needed. This code has originally been written by Rami Rosen <rosenr@marvell.com>, and then reviewed and cleaned up by Thomas Petazzoni <thomas.petazzoni@free-electrons.com>. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: David S. Miller <davem@davemloft.net>
2012-08-17 18:04:28 +07:00
obj-$(CONFIG_MVNETA) += mvneta.o
skge/sky2/mv643xx/pxa168: Move the Marvell Ethernet drivers Move the Marvell Ethernet drivers into drivers/net/ethernet/marvell/ and make the necessary Kconfig and Makefile changes. CC: Sachin Sanap <ssanap@marvell.com> CC: Zhangfei Gao <zgao6@marvell.com> CC: Philip Rakity <prakity@marvell.com> CC: Mark Brown <markb@marvell.com> CC: Lennert Buytenhek <buytenh@marvell.com> CC: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-05-21 10:18:55 +07:00
obj-$(CONFIG_PXA168_ETH) += pxa168_eth.o
obj-$(CONFIG_SKGE) += skge.o
obj-$(CONFIG_SKY2) += sky2.o
Reference in New Issue Copy Permalink