mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-05 16:36:43 +07:00
120 lines
5.8 KiB
Plaintext
120 lines
5.8 KiB
Plaintext
|
GPIO Interfaces
|
||
|
===============
|
||
|
|
||
|
The documents in this directory give detailed instructions on how to access
|
||
|
GPIOs in drivers, and how to write a driver for a device that provides GPIOs
|
||
|
itself.
|
||
|
|
||
|
Due to the history of GPIO interfaces in the kernel, there are two different
|
||
|
ways to obtain and use GPIOs:
|
||
|
|
||
|
- The descriptor-based interface is the preferred way to manipulate GPIOs,
|
||
|
and is described by all the files in this directory excepted gpio-legacy.txt.
|
||
|
- The legacy integer-based interface which is considered deprecated (but still
|
||
|
usable for compatibility reasons) is documented in gpio-legacy.txt.
|
||
|
|
||
|
The remainder of this document applies to the new descriptor-based interface.
|
||
|
gpio-legacy.txt contains the same information applied to the legacy
|
||
|
integer-based interface.
|
||
|
|
||
|
|
||
|
What is a GPIO?
|
||
|
===============
|
||
|
|
||
|
A "General Purpose Input/Output" (GPIO) is a flexible software-controlled
|
||
|
digital signal. They are provided from many kinds of chip, and are familiar
|
||
|
to Linux developers working with embedded and custom hardware. Each GPIO
|
||
|
represents a bit connected to a particular pin, or "ball" on Ball Grid Array
|
||
|
(BGA) packages. Board schematics show which external hardware connects to
|
||
|
which GPIOs. Drivers can be written generically, so that board setup code
|
||
|
passes such pin configuration data to drivers.
|
||
|
|
||
|
System-on-Chip (SOC) processors heavily rely on GPIOs. In some cases, every
|
||
|
non-dedicated pin can be configured as a GPIO; and most chips have at least
|
||
|
several dozen of them. Programmable logic devices (like FPGAs) can easily
|
||
|
provide GPIOs; multifunction chips like power managers, and audio codecs
|
||
|
often have a few such pins to help with pin scarcity on SOCs; and there are
|
||
|
also "GPIO Expander" chips that connect using the I2C or SPI serial buses.
|
||
|
Most PC southbridges have a few dozen GPIO-capable pins (with only the BIOS
|
||
|
firmware knowing how they're used).
|
||
|
|
||
|
The exact capabilities of GPIOs vary between systems. Common options:
|
||
|
|
||
|
- Output values are writable (high=1, low=0). Some chips also have
|
||
|
options about how that value is driven, so that for example only one
|
||
|
value might be driven, supporting "wire-OR" and similar schemes for the
|
||
|
other value (notably, "open drain" signaling).
|
||
|
|
||
|
- Input values are likewise readable (1, 0). Some chips support readback
|
||
|
of pins configured as "output", which is very useful in such "wire-OR"
|
||
|
cases (to support bidirectional signaling). GPIO controllers may have
|
||
|
input de-glitch/debounce logic, sometimes with software controls.
|
||
|
|
||
|
- Inputs can often be used as IRQ signals, often edge triggered but
|
||
|
sometimes level triggered. Such IRQs may be configurable as system
|
||
|
wakeup events, to wake the system from a low power state.
|
||
|
|
||
|
- Usually a GPIO will be configurable as either input or output, as needed
|
||
|
by different product boards; single direction ones exist too.
|
||
|
|
||
|
- Most GPIOs can be accessed while holding spinlocks, but those accessed
|
||
|
through a serial bus normally can't. Some systems support both types.
|
||
|
|
||
|
On a given board each GPIO is used for one specific purpose like monitoring
|
||
|
MMC/SD card insertion/removal, detecting card write-protect status, driving
|
||
|
a LED, configuring a transceiver, bit-banging a serial bus, poking a hardware
|
||
|
watchdog, sensing a switch, and so on.
|
||
|
|
||
|
|
||
|
Common GPIO Properties
|
||
|
======================
|
||
|
|
||
|
These properties are met through all the other documents of the GPIO interface
|
||
|
and it is useful to understand them, especially if you need to define GPIO
|
||
|
mappings.
|
||
|
|
||
|
Active-High and Active-Low
|
||
|
--------------------------
|
||
|
It is natural to assume that a GPIO is "active" when its output signal is 1
|
||
|
("high"), and inactive when it is 0 ("low"). However in practice the signal of a
|
||
|
GPIO may be inverted before is reaches its destination, or a device could decide
|
||
|
to have different conventions about what "active" means. Such decisions should
|
||
|
be transparent to device drivers, therefore it is possible to define a GPIO as
|
||
|
being either active-high ("1" means "active", the default) or active-low ("0"
|
||
|
means "active") so that drivers only need to worry about the logical signal and
|
||
|
not about what happens at the line level.
|
||
|
|
||
|
Open Drain and Open Source
|
||
|
--------------------------
|
||
|
Sometimes shared signals need to use "open drain" (where only the low signal
|
||
|
level is actually driven), or "open source" (where only the high signal level is
|
||
|
driven) signaling. That term applies to CMOS transistors; "open collector" is
|
||
|
used for TTL. A pullup or pulldown resistor causes the high or low signal level.
|
||
|
This is sometimes called a "wire-AND"; or more practically, from the negative
|
||
|
logic (low=true) perspective this is a "wire-OR".
|
||
|
|
||
|
One common example of an open drain signal is a shared active-low IRQ line.
|
||
|
Also, bidirectional data bus signals sometimes use open drain signals.
|
||
|
|
||
|
Some GPIO controllers directly support open drain and open source outputs; many
|
||
|
don't. When you need open drain signaling but your hardware doesn't directly
|
||
|
support it, there's a common idiom you can use to emulate it with any GPIO pin
|
||
|
that can be used as either an input or an output:
|
||
|
|
||
|
LOW: gpiod_direction_output(gpio, 0) ... this drives the signal and overrides
|
||
|
the pullup.
|
||
|
|
||
|
HIGH: gpiod_direction_input(gpio) ... this turns off the output, so the pullup
|
||
|
(or some other device) controls the signal.
|
||
|
|
||
|
The same logic can be applied to emulate open source signaling, by driving the
|
||
|
high signal and configuring the GPIO as input for low. This open drain/open
|
||
|
source emulation can be handled transparently by the GPIO framework.
|
||
|
|
||
|
If you are "driving" the signal high but gpiod_get_value(gpio) reports a low
|
||
|
value (after the appropriate rise time passes), you know some other component is
|
||
|
driving the shared signal low. That's not necessarily an error. As one common
|
||
|
example, that's how I2C clocks are stretched: a slave that needs a slower clock
|
||
|
delays the rising edge of SCK, and the I2C master adjusts its signaling rate
|
||
|
accordingly.
|