linux_dsm_epyc7002/drivers/net/ipvlan/ipvlan_main.c

1129 lines
29 KiB
C
Raw Normal View History

ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
/* Copyright (c) 2014 Mahesh Bandewar <maheshb@google.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
*/
#include "ipvlan.h"
static unsigned int ipvlan_netid __read_mostly;
struct ipvlan_netns {
unsigned int ipvl_nf_hook_refcnt;
};
static const struct nf_hook_ops ipvl_nfops[] = {
{
.hook = ipvlan_nf_input,
.pf = NFPROTO_IPV4,
.hooknum = NF_INET_LOCAL_IN,
.priority = INT_MAX,
},
#if IS_ENABLED(CONFIG_IPV6)
{
.hook = ipvlan_nf_input,
.pf = NFPROTO_IPV6,
.hooknum = NF_INET_LOCAL_IN,
.priority = INT_MAX,
},
#endif
};
static const struct l3mdev_ops ipvl_l3mdev_ops = {
.l3mdev_l3_rcv = ipvlan_l3_rcv,
};
static void ipvlan_adjust_mtu(struct ipvl_dev *ipvlan, struct net_device *dev)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
ipvlan->dev->mtu = dev->mtu;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
static int ipvlan_register_nf_hook(struct net *net)
{
struct ipvlan_netns *vnet = net_generic(net, ipvlan_netid);
int err = 0;
if (!vnet->ipvl_nf_hook_refcnt) {
err = nf_register_net_hooks(net, ipvl_nfops,
ARRAY_SIZE(ipvl_nfops));
if (!err)
vnet->ipvl_nf_hook_refcnt = 1;
} else {
vnet->ipvl_nf_hook_refcnt++;
}
return err;
}
static void ipvlan_unregister_nf_hook(struct net *net)
{
struct ipvlan_netns *vnet = net_generic(net, ipvlan_netid);
if (WARN_ON(!vnet->ipvl_nf_hook_refcnt))
return;
vnet->ipvl_nf_hook_refcnt--;
if (!vnet->ipvl_nf_hook_refcnt)
nf_unregister_net_hooks(net, ipvl_nfops,
ARRAY_SIZE(ipvl_nfops));
}
static int ipvlan_set_port_mode(struct ipvl_port *port, u16 nval)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
struct ipvl_dev *ipvlan;
struct net_device *mdev = port->dev;
ipvlan: call dev_change_flags when ipvlan mode is reset After we change the ipvlan mode from l3 to l2, or vice versa, we only reset IFF_NOARP flag, but don't flush the ARP table cache, which will cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2(). Then the message will not come out of host. Here is the reproducer on local host: ip link set eth1 up ip addr add 192.168.1.1/24 dev eth1 ip link add link eth1 ipvlan1 type ipvlan mode l3 ip netns add net1 ip link set ipvlan1 netns net1 ip netns exec net1 ip link set ipvlan1 up ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1 ip route add 192.168.2.0/24 via 192.168.1.2 ping 192.168.2.2 -c 2 ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2 ping 192.168.2.2 -c 2 Add the same configuration on remote host. After we set the mode to l2, we could find that the src/dst MAC addresses are the same on eth1: 21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64 Fix this by calling dev_change_flags(), which will call netdevice notifier with flag change info. v2: a) As pointed out by Wang Cong, check return value for dev_change_flags() when change dev flags. b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops. So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path. Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-01 15:21:21 +07:00
unsigned int flags;
int err;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
ASSERT_RTNL();
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (port->mode != nval) {
ipvlan: call dev_change_flags when ipvlan mode is reset After we change the ipvlan mode from l3 to l2, or vice versa, we only reset IFF_NOARP flag, but don't flush the ARP table cache, which will cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2(). Then the message will not come out of host. Here is the reproducer on local host: ip link set eth1 up ip addr add 192.168.1.1/24 dev eth1 ip link add link eth1 ipvlan1 type ipvlan mode l3 ip netns add net1 ip link set ipvlan1 netns net1 ip netns exec net1 ip link set ipvlan1 up ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1 ip route add 192.168.2.0/24 via 192.168.1.2 ping 192.168.2.2 -c 2 ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2 ping 192.168.2.2 -c 2 Add the same configuration on remote host. After we set the mode to l2, we could find that the src/dst MAC addresses are the same on eth1: 21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64 Fix this by calling dev_change_flags(), which will call netdevice notifier with flag change info. v2: a) As pointed out by Wang Cong, check return value for dev_change_flags() when change dev flags. b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops. So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path. Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-01 15:21:21 +07:00
list_for_each_entry(ipvlan, &port->ipvlans, pnode) {
flags = ipvlan->dev->flags;
if (nval == IPVLAN_MODE_L3 || nval == IPVLAN_MODE_L3S) {
err = dev_change_flags(ipvlan->dev,
flags | IFF_NOARP);
} else {
err = dev_change_flags(ipvlan->dev,
flags & ~IFF_NOARP);
}
if (unlikely(err))
goto fail;
}
if (nval == IPVLAN_MODE_L3S) {
/* New mode is L3S */
err = ipvlan_register_nf_hook(read_pnet(&port->pnet));
if (!err) {
mdev->l3mdev_ops = &ipvl_l3mdev_ops;
mdev->priv_flags |= IFF_L3MDEV_MASTER;
} else
ipvlan: call dev_change_flags when ipvlan mode is reset After we change the ipvlan mode from l3 to l2, or vice versa, we only reset IFF_NOARP flag, but don't flush the ARP table cache, which will cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2(). Then the message will not come out of host. Here is the reproducer on local host: ip link set eth1 up ip addr add 192.168.1.1/24 dev eth1 ip link add link eth1 ipvlan1 type ipvlan mode l3 ip netns add net1 ip link set ipvlan1 netns net1 ip netns exec net1 ip link set ipvlan1 up ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1 ip route add 192.168.2.0/24 via 192.168.1.2 ping 192.168.2.2 -c 2 ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2 ping 192.168.2.2 -c 2 Add the same configuration on remote host. After we set the mode to l2, we could find that the src/dst MAC addresses are the same on eth1: 21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64 Fix this by calling dev_change_flags(), which will call netdevice notifier with flag change info. v2: a) As pointed out by Wang Cong, check return value for dev_change_flags() when change dev flags. b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops. So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path. Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-01 15:21:21 +07:00
goto fail;
} else if (port->mode == IPVLAN_MODE_L3S) {
/* Old mode was L3S */
mdev->priv_flags &= ~IFF_L3MDEV_MASTER;
ipvlan_unregister_nf_hook(read_pnet(&port->pnet));
mdev->l3mdev_ops = NULL;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
port->mode = nval;
}
ipvlan: call dev_change_flags when ipvlan mode is reset After we change the ipvlan mode from l3 to l2, or vice versa, we only reset IFF_NOARP flag, but don't flush the ARP table cache, which will cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2(). Then the message will not come out of host. Here is the reproducer on local host: ip link set eth1 up ip addr add 192.168.1.1/24 dev eth1 ip link add link eth1 ipvlan1 type ipvlan mode l3 ip netns add net1 ip link set ipvlan1 netns net1 ip netns exec net1 ip link set ipvlan1 up ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1 ip route add 192.168.2.0/24 via 192.168.1.2 ping 192.168.2.2 -c 2 ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2 ping 192.168.2.2 -c 2 Add the same configuration on remote host. After we set the mode to l2, we could find that the src/dst MAC addresses are the same on eth1: 21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64 Fix this by calling dev_change_flags(), which will call netdevice notifier with flag change info. v2: a) As pointed out by Wang Cong, check return value for dev_change_flags() when change dev flags. b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops. So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path. Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-01 15:21:21 +07:00
return 0;
fail:
/* Undo the flags changes that have been done so far. */
list_for_each_entry_continue_reverse(ipvlan, &port->ipvlans, pnode) {
flags = ipvlan->dev->flags;
if (port->mode == IPVLAN_MODE_L3 ||
port->mode == IPVLAN_MODE_L3S)
dev_change_flags(ipvlan->dev, flags | IFF_NOARP);
else
dev_change_flags(ipvlan->dev, flags & ~IFF_NOARP);
}
return err;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
static int ipvlan_port_create(struct net_device *dev)
{
struct ipvl_port *port;
int err, idx;
port = kzalloc(sizeof(struct ipvl_port), GFP_KERNEL);
if (!port)
return -ENOMEM;
write_pnet(&port->pnet, dev_net(dev));
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
port->dev = dev;
port->mode = IPVLAN_MODE_L3;
INIT_LIST_HEAD(&port->ipvlans);
for (idx = 0; idx < IPVLAN_HASH_SIZE; idx++)
INIT_HLIST_HEAD(&port->hlhead[idx]);
skb_queue_head_init(&port->backlog);
INIT_WORK(&port->wq, ipvlan_process_multicast);
ida_init(&port->ida);
port->dev_id_start = 1;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
err = netdev_rx_handler_register(dev, ipvlan_handle_frame, port);
if (err)
goto err;
return 0;
err:
kfree(port);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return err;
}
static void ipvlan_port_destroy(struct net_device *dev)
{
struct ipvl_port *port = ipvlan_port_get_rtnl(dev);
struct sk_buff *skb;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (port->mode == IPVLAN_MODE_L3S) {
dev->priv_flags &= ~IFF_L3MDEV_MASTER;
ipvlan_unregister_nf_hook(dev_net(dev));
dev->l3mdev_ops = NULL;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
netdev_rx_handler_unregister(dev);
cancel_work_sync(&port->wq);
while ((skb = __skb_dequeue(&port->backlog)) != NULL) {
if (skb->dev)
dev_put(skb->dev);
kfree_skb(skb);
}
ida_destroy(&port->ida);
kfree(port);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
#define IPVLAN_FEATURES \
(NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_HIGHDMA | NETIF_F_FRAGLIST | \
NETIF_F_GSO | NETIF_F_TSO | NETIF_F_GSO_ROBUST | \
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
NETIF_F_TSO_ECN | NETIF_F_TSO6 | NETIF_F_GRO | NETIF_F_RXCSUM | \
NETIF_F_HW_VLAN_CTAG_FILTER | NETIF_F_HW_VLAN_STAG_FILTER)
#define IPVLAN_STATE_MASK \
((1<<__LINK_STATE_NOCARRIER) | (1<<__LINK_STATE_DORMANT))
static int ipvlan_init(struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
struct ipvl_port *port;
int err;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
dev->state = (dev->state & ~IPVLAN_STATE_MASK) |
(phy_dev->state & IPVLAN_STATE_MASK);
dev->features = phy_dev->features & IPVLAN_FEATURES;
dev->features |= NETIF_F_LLTX | NETIF_F_VLAN_CHALLENGED;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
dev->gso_max_size = phy_dev->gso_max_size;
dev->gso_max_segs = phy_dev->gso_max_segs;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
dev->hard_header_len = phy_dev->hard_header_len;
netdev_lockdep_set_classes(dev);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
ipvlan->pcpu_stats = netdev_alloc_pcpu_stats(struct ipvl_pcpu_stats);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (!ipvlan->pcpu_stats)
return -ENOMEM;
if (!netif_is_ipvlan_port(phy_dev)) {
err = ipvlan_port_create(phy_dev);
if (err < 0) {
free_percpu(ipvlan->pcpu_stats);
return err;
}
}
port = ipvlan_port_get_rtnl(phy_dev);
port->count += 1;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return 0;
}
static void ipvlan_uninit(struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
struct ipvl_port *port;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
free_percpu(ipvlan->pcpu_stats);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
port = ipvlan_port_get_rtnl(phy_dev);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
port->count -= 1;
if (!port->count)
ipvlan_port_destroy(port->dev);
}
static int ipvlan_open(struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
struct ipvl_addr *addr;
if (ipvlan->port->mode == IPVLAN_MODE_L3 ||
ipvlan->port->mode == IPVLAN_MODE_L3S)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
dev->flags |= IFF_NOARP;
else
dev->flags &= ~IFF_NOARP;
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
rcu_read_lock();
list_for_each_entry_rcu(addr, &ipvlan->addrs, anode)
ipvlan_ht_addr_add(ipvlan, addr);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
rcu_read_unlock();
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return dev_uc_add(phy_dev, phy_dev->dev_addr);
}
static int ipvlan_stop(struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
struct ipvl_addr *addr;
dev_uc_unsync(phy_dev, dev);
dev_mc_unsync(phy_dev, dev);
dev_uc_del(phy_dev, phy_dev->dev_addr);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
rcu_read_lock();
list_for_each_entry_rcu(addr, &ipvlan->addrs, anode)
ipvlan_ht_addr_del(addr);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
rcu_read_unlock();
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return 0;
}
static netdev_tx_t ipvlan_start_xmit(struct sk_buff *skb,
struct net_device *dev)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
const struct ipvl_dev *ipvlan = netdev_priv(dev);
int skblen = skb->len;
int ret;
ret = ipvlan_queue_xmit(skb, dev);
if (likely(ret == NET_XMIT_SUCCESS || ret == NET_XMIT_CN)) {
struct ipvl_pcpu_stats *pcptr;
pcptr = this_cpu_ptr(ipvlan->pcpu_stats);
u64_stats_update_begin(&pcptr->syncp);
pcptr->tx_pkts++;
pcptr->tx_bytes += skblen;
u64_stats_update_end(&pcptr->syncp);
} else {
this_cpu_inc(ipvlan->pcpu_stats->tx_drps);
}
return ret;
}
static netdev_features_t ipvlan_fix_features(struct net_device *dev,
netdev_features_t features)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
return features & (ipvlan->sfeatures | ~IPVLAN_FEATURES);
}
static void ipvlan_change_rx_flags(struct net_device *dev, int change)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
if (change & IFF_ALLMULTI)
dev_set_allmulti(phy_dev, dev->flags & IFF_ALLMULTI? 1 : -1);
}
static void ipvlan_set_multicast_mac_filter(struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
if (dev->flags & (IFF_PROMISC | IFF_ALLMULTI)) {
bitmap_fill(ipvlan->mac_filters, IPVLAN_MAC_FILTER_SIZE);
} else {
struct netdev_hw_addr *ha;
DECLARE_BITMAP(mc_filters, IPVLAN_MAC_FILTER_SIZE);
bitmap_zero(mc_filters, IPVLAN_MAC_FILTER_SIZE);
netdev_for_each_mc_addr(ha, dev)
__set_bit(ipvlan_mac_hash(ha->addr), mc_filters);
/* Turn-on broadcast bit irrespective of address family,
* since broadcast is deferred to a work-queue, hence no
* impact on fast-path processing.
*/
__set_bit(ipvlan_mac_hash(dev->broadcast), mc_filters);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
bitmap_copy(ipvlan->mac_filters, mc_filters,
IPVLAN_MAC_FILTER_SIZE);
}
dev_uc_sync(ipvlan->phy_dev, dev);
dev_mc_sync(ipvlan->phy_dev, dev);
}
static void ipvlan_get_stats64(struct net_device *dev,
struct rtnl_link_stats64 *s)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
if (ipvlan->pcpu_stats) {
struct ipvl_pcpu_stats *pcptr;
u64 rx_pkts, rx_bytes, rx_mcast, tx_pkts, tx_bytes;
u32 rx_errs = 0, tx_drps = 0;
u32 strt;
int idx;
for_each_possible_cpu(idx) {
pcptr = per_cpu_ptr(ipvlan->pcpu_stats, idx);
do {
strt= u64_stats_fetch_begin_irq(&pcptr->syncp);
rx_pkts = pcptr->rx_pkts;
rx_bytes = pcptr->rx_bytes;
rx_mcast = pcptr->rx_mcast;
tx_pkts = pcptr->tx_pkts;
tx_bytes = pcptr->tx_bytes;
} while (u64_stats_fetch_retry_irq(&pcptr->syncp,
strt));
s->rx_packets += rx_pkts;
s->rx_bytes += rx_bytes;
s->multicast += rx_mcast;
s->tx_packets += tx_pkts;
s->tx_bytes += tx_bytes;
/* u32 values are updated without syncp protection. */
rx_errs += pcptr->rx_errs;
tx_drps += pcptr->tx_drps;
}
s->rx_errors = rx_errs;
s->rx_dropped = rx_errs;
s->tx_dropped = tx_drps;
}
}
static int ipvlan_vlan_rx_add_vid(struct net_device *dev, __be16 proto, u16 vid)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
return vlan_vid_add(phy_dev, proto, vid);
}
static int ipvlan_vlan_rx_kill_vid(struct net_device *dev, __be16 proto,
u16 vid)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
vlan_vid_del(phy_dev, proto, vid);
return 0;
}
static int ipvlan_get_iflink(const struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
return ipvlan->phy_dev->ifindex;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static const struct net_device_ops ipvlan_netdev_ops = {
.ndo_init = ipvlan_init,
.ndo_uninit = ipvlan_uninit,
.ndo_open = ipvlan_open,
.ndo_stop = ipvlan_stop,
.ndo_start_xmit = ipvlan_start_xmit,
.ndo_fix_features = ipvlan_fix_features,
.ndo_change_rx_flags = ipvlan_change_rx_flags,
.ndo_set_rx_mode = ipvlan_set_multicast_mac_filter,
.ndo_get_stats64 = ipvlan_get_stats64,
.ndo_vlan_rx_add_vid = ipvlan_vlan_rx_add_vid,
.ndo_vlan_rx_kill_vid = ipvlan_vlan_rx_kill_vid,
.ndo_get_iflink = ipvlan_get_iflink,
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
};
static int ipvlan_hard_header(struct sk_buff *skb, struct net_device *dev,
unsigned short type, const void *daddr,
const void *saddr, unsigned len)
{
const struct ipvl_dev *ipvlan = netdev_priv(dev);
struct net_device *phy_dev = ipvlan->phy_dev;
/* TODO Probably use a different field than dev_addr so that the
* mac-address on the virtual device is portable and can be carried
* while the packets use the mac-addr on the physical device.
*/
return dev_hard_header(skb, phy_dev, type, daddr,
saddr ? : phy_dev->dev_addr, len);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
static const struct header_ops ipvlan_header_ops = {
.create = ipvlan_hard_header,
.parse = eth_header_parse,
.cache = eth_header_cache,
.cache_update = eth_header_cache_update,
};
static bool netif_is_ipvlan(const struct net_device *dev)
{
/* both ipvlan and ipvtap devices use the same netdev_ops */
return dev->netdev_ops == &ipvlan_netdev_ops;
}
static int ipvlan_ethtool_get_link_ksettings(struct net_device *dev,
struct ethtool_link_ksettings *cmd)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
const struct ipvl_dev *ipvlan = netdev_priv(dev);
return __ethtool_get_link_ksettings(ipvlan->phy_dev, cmd);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
static void ipvlan_ethtool_get_drvinfo(struct net_device *dev,
struct ethtool_drvinfo *drvinfo)
{
strlcpy(drvinfo->driver, IPVLAN_DRV, sizeof(drvinfo->driver));
strlcpy(drvinfo->version, IPV_DRV_VER, sizeof(drvinfo->version));
}
static u32 ipvlan_ethtool_get_msglevel(struct net_device *dev)
{
const struct ipvl_dev *ipvlan = netdev_priv(dev);
return ipvlan->msg_enable;
}
static void ipvlan_ethtool_set_msglevel(struct net_device *dev, u32 value)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
ipvlan->msg_enable = value;
}
static const struct ethtool_ops ipvlan_ethtool_ops = {
.get_link = ethtool_op_get_link,
.get_link_ksettings = ipvlan_ethtool_get_link_ksettings,
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
.get_drvinfo = ipvlan_ethtool_get_drvinfo,
.get_msglevel = ipvlan_ethtool_get_msglevel,
.set_msglevel = ipvlan_ethtool_set_msglevel,
};
static int ipvlan_nl_changelink(struct net_device *dev,
struct nlattr *tb[], struct nlattr *data[],
struct netlink_ext_ack *extack)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct ipvl_port *port = ipvlan_port_get_rtnl(ipvlan->phy_dev);
int err = 0;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (!data)
return 0;
if (data[IFLA_IPVLAN_MODE]) {
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
u16 nmode = nla_get_u16(data[IFLA_IPVLAN_MODE]);
err = ipvlan_set_port_mode(port, nmode);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
if (!err && data[IFLA_IPVLAN_FLAGS]) {
u16 flags = nla_get_u16(data[IFLA_IPVLAN_FLAGS]);
if (flags & IPVLAN_F_PRIVATE)
ipvlan_mark_private(port);
else
ipvlan_clear_private(port);
if (flags & IPVLAN_F_VEPA)
ipvlan_mark_vepa(port);
else
ipvlan_clear_vepa(port);
}
return err;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
static size_t ipvlan_nl_getsize(const struct net_device *dev)
{
return (0
+ nla_total_size(2) /* IFLA_IPVLAN_MODE */
+ nla_total_size(2) /* IFLA_IPVLAN_FLAGS */
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
);
}
static int ipvlan_nl_validate(struct nlattr *tb[], struct nlattr *data[],
struct netlink_ext_ack *extack)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
if (!data)
return 0;
if (data[IFLA_IPVLAN_MODE]) {
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
u16 mode = nla_get_u16(data[IFLA_IPVLAN_MODE]);
if (mode < IPVLAN_MODE_L2 || mode >= IPVLAN_MODE_MAX)
return -EINVAL;
}
if (data[IFLA_IPVLAN_FLAGS]) {
u16 flags = nla_get_u16(data[IFLA_IPVLAN_FLAGS]);
/* Only two bits are used at this moment. */
if (flags & ~(IPVLAN_F_PRIVATE | IPVLAN_F_VEPA))
return -EINVAL;
/* Also both flags can't be active at the same time. */
if ((flags & (IPVLAN_F_PRIVATE | IPVLAN_F_VEPA)) ==
(IPVLAN_F_PRIVATE | IPVLAN_F_VEPA))
return -EINVAL;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return 0;
}
static int ipvlan_nl_fillinfo(struct sk_buff *skb,
const struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct ipvl_port *port = ipvlan_port_get_rtnl(ipvlan->phy_dev);
int ret = -EINVAL;
if (!port)
goto err;
ret = -EMSGSIZE;
if (nla_put_u16(skb, IFLA_IPVLAN_MODE, port->mode))
goto err;
if (nla_put_u16(skb, IFLA_IPVLAN_FLAGS, port->flags))
goto err;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return 0;
err:
return ret;
}
int ipvlan_link_new(struct net *src_net, struct net_device *dev,
struct nlattr *tb[], struct nlattr *data[],
struct netlink_ext_ack *extack)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct ipvl_port *port;
struct net_device *phy_dev;
int err;
u16 mode = IPVLAN_MODE_L3;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (!tb[IFLA_LINK])
return -EINVAL;
phy_dev = __dev_get_by_index(src_net, nla_get_u32(tb[IFLA_LINK]));
if (!phy_dev)
return -ENODEV;
if (netif_is_ipvlan(phy_dev)) {
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
struct ipvl_dev *tmp = netdev_priv(phy_dev);
phy_dev = tmp->phy_dev;
} else if (!netif_is_ipvlan_port(phy_dev)) {
/* Exit early if the underlying link is invalid or busy */
if (phy_dev->type != ARPHRD_ETHER ||
phy_dev->flags & IFF_LOOPBACK) {
netdev_err(phy_dev,
"Master is either lo or non-ether device\n");
return -EINVAL;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (netdev_is_rx_handler_busy(phy_dev)) {
netdev_err(phy_dev, "Device is already in use.\n");
return -EBUSY;
}
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
ipvlan->phy_dev = phy_dev;
ipvlan->dev = dev;
ipvlan->sfeatures = IPVLAN_FEATURES;
if (!tb[IFLA_MTU])
ipvlan_adjust_mtu(ipvlan, phy_dev);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
INIT_LIST_HEAD(&ipvlan->addrs);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
spin_lock_init(&ipvlan->addrs_lock);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
/* TODO Probably put random address here to be presented to the
* world but keep using the physical-dev address for the outgoing
* packets.
*/
memcpy(dev->dev_addr, phy_dev->dev_addr, ETH_ALEN);
dev->priv_flags |= IFF_NO_RX_HANDLER;
err = register_netdevice(dev);
if (err < 0)
return err;
/* ipvlan_init() would have created the port, if required */
port = ipvlan_port_get_rtnl(phy_dev);
ipvlan->port = port;
/* If the port-id base is at the MAX value, then wrap it around and
* begin from 0x1 again. This may be due to a busy system where lots
* of slaves are getting created and deleted.
*/
if (port->dev_id_start == 0xFFFE)
port->dev_id_start = 0x1;
/* Since L2 address is shared among all IPvlan slaves including
* master, use unique 16 bit dev-ids to diffentiate among them.
* Assign IDs between 0x1 and 0xFFFE (used by the master) to each
* slave link [see addrconf_ifid_eui48()].
*/
err = ida_simple_get(&port->ida, port->dev_id_start, 0xFFFE,
GFP_KERNEL);
if (err < 0)
err = ida_simple_get(&port->ida, 0x1, port->dev_id_start,
GFP_KERNEL);
if (err < 0)
goto unregister_netdev;
dev->dev_id = err;
/* Increment id-base to the next slot for the future assignment */
port->dev_id_start = err + 1;
err = netdev_upper_dev_link(phy_dev, dev, extack);
if (err)
goto remove_ida;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
/* Flags are per port and latest update overrides. User has
* to be consistent in setting it just like the mode attribute.
*/
if (data && data[IFLA_IPVLAN_FLAGS])
port->flags = nla_get_u16(data[IFLA_IPVLAN_FLAGS]);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (data && data[IFLA_IPVLAN_MODE])
mode = nla_get_u16(data[IFLA_IPVLAN_MODE]);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
err = ipvlan_set_port_mode(port, mode);
if (err)
goto unlink_netdev;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
list_add_tail_rcu(&ipvlan->pnode, &port->ipvlans);
netif_stacked_transfer_operstate(phy_dev, dev);
return 0;
unlink_netdev:
netdev_upper_dev_unlink(phy_dev, dev);
remove_ida:
ida_simple_remove(&port->ida, dev->dev_id);
unregister_netdev:
unregister_netdevice(dev);
return err;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
EXPORT_SYMBOL_GPL(ipvlan_link_new);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
void ipvlan_link_delete(struct net_device *dev, struct list_head *head)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct ipvl_addr *addr, *next;
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
spin_lock_bh(&ipvlan->addrs_lock);
list_for_each_entry_safe(addr, next, &ipvlan->addrs, anode) {
ipvlan_ht_addr_del(addr);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
list_del_rcu(&addr->anode);
kfree_rcu(addr, rcu);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
spin_unlock_bh(&ipvlan->addrs_lock);
ida_simple_remove(&ipvlan->port->ida, dev->dev_id);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
list_del_rcu(&ipvlan->pnode);
unregister_netdevice_queue(dev, head);
netdev_upper_dev_unlink(ipvlan->phy_dev, dev);
}
EXPORT_SYMBOL_GPL(ipvlan_link_delete);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
void ipvlan_link_setup(struct net_device *dev)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
ether_setup(dev);
dev->max_mtu = ETH_MAX_MTU;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
dev->priv_flags &= ~(IFF_XMIT_DST_RELEASE | IFF_TX_SKB_SHARING);
dev->priv_flags |= IFF_UNICAST_FLT | IFF_NO_QUEUE;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
dev->netdev_ops = &ipvlan_netdev_ops;
net: Fix inconsistent teardown and release of private netdev state. Network devices can allocate reasources and private memory using netdev_ops->ndo_init(). However, the release of these resources can occur in one of two different places. Either netdev_ops->ndo_uninit() or netdev->destructor(). The decision of which operation frees the resources depends upon whether it is necessary for all netdev refs to be released before it is safe to perform the freeing. netdev_ops->ndo_uninit() presumably can occur right after the NETDEV_UNREGISTER notifier completes and the unicast and multicast address lists are flushed. netdev->destructor(), on the other hand, does not run until the netdev references all go away. Further complicating the situation is that netdev->destructor() almost universally does also a free_netdev(). This creates a problem for the logic in register_netdevice(). Because all callers of register_netdevice() manage the freeing of the netdev, and invoke free_netdev(dev) if register_netdevice() fails. If netdev_ops->ndo_init() succeeds, but something else fails inside of register_netdevice(), it does call ndo_ops->ndo_uninit(). But it is not able to invoke netdev->destructor(). This is because netdev->destructor() will do a free_netdev() and then the caller of register_netdevice() will do the same. However, this means that the resources that would normally be released by netdev->destructor() will not be. Over the years drivers have added local hacks to deal with this, by invoking their destructor parts by hand when register_netdevice() fails. Many drivers do not try to deal with this, and instead we have leaks. Let's close this hole by formalizing the distinction between what private things need to be freed up by netdev->destructor() and whether the driver needs unregister_netdevice() to perform the free_netdev(). netdev->priv_destructor() performs all actions to free up the private resources that used to be freed by netdev->destructor(), except for free_netdev(). netdev->needs_free_netdev is a boolean that indicates whether free_netdev() should be done at the end of unregister_netdevice(). Now, register_netdevice() can sanely release all resources after ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit() and netdev->priv_destructor(). And at the end of unregister_netdevice(), we invoke netdev->priv_destructor() and optionally call free_netdev(). Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-08 23:52:56 +07:00
dev->needs_free_netdev = true;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
dev->header_ops = &ipvlan_header_ops;
dev->ethtool_ops = &ipvlan_ethtool_ops;
}
EXPORT_SYMBOL_GPL(ipvlan_link_setup);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static const struct nla_policy ipvlan_nl_policy[IFLA_IPVLAN_MAX + 1] =
{
[IFLA_IPVLAN_MODE] = { .type = NLA_U16 },
[IFLA_IPVLAN_FLAGS] = { .type = NLA_U16 },
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
};
static struct rtnl_link_ops ipvlan_link_ops = {
.kind = "ipvlan",
.priv_size = sizeof(struct ipvl_dev),
.setup = ipvlan_link_setup,
.newlink = ipvlan_link_new,
.dellink = ipvlan_link_delete,
};
int ipvlan_link_register(struct rtnl_link_ops *ops)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
ops->get_size = ipvlan_nl_getsize;
ops->policy = ipvlan_nl_policy;
ops->validate = ipvlan_nl_validate;
ops->fill_info = ipvlan_nl_fillinfo;
ops->changelink = ipvlan_nl_changelink;
ops->maxtype = IFLA_IPVLAN_MAX;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return rtnl_link_register(ops);
}
EXPORT_SYMBOL_GPL(ipvlan_link_register);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static int ipvlan_device_event(struct notifier_block *unused,
unsigned long event, void *ptr)
{
struct net_device *dev = netdev_notifier_info_to_dev(ptr);
struct ipvl_dev *ipvlan, *next;
struct ipvl_port *port;
LIST_HEAD(lst_kill);
if (!netif_is_ipvlan_port(dev))
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return NOTIFY_DONE;
port = ipvlan_port_get_rtnl(dev);
switch (event) {
case NETDEV_CHANGE:
list_for_each_entry(ipvlan, &port->ipvlans, pnode)
netif_stacked_transfer_operstate(ipvlan->phy_dev,
ipvlan->dev);
break;
case NETDEV_REGISTER: {
struct net *oldnet, *newnet = dev_net(dev);
struct ipvlan_netns *old_vnet;
oldnet = read_pnet(&port->pnet);
if (net_eq(newnet, oldnet))
break;
write_pnet(&port->pnet, newnet);
old_vnet = net_generic(oldnet, ipvlan_netid);
if (!old_vnet->ipvl_nf_hook_refcnt)
break;
ipvlan_register_nf_hook(newnet);
ipvlan_unregister_nf_hook(oldnet);
break;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
case NETDEV_UNREGISTER:
if (dev->reg_state != NETREG_UNREGISTERING)
break;
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
list_for_each_entry_safe(ipvlan, next, &port->ipvlans, pnode)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
ipvlan->dev->rtnl_link_ops->dellink(ipvlan->dev,
&lst_kill);
unregister_netdevice_many(&lst_kill);
break;
case NETDEV_FEAT_CHANGE:
list_for_each_entry(ipvlan, &port->ipvlans, pnode) {
ipvlan->dev->features = dev->features & IPVLAN_FEATURES;
ipvlan->dev->gso_max_size = dev->gso_max_size;
ipvlan->dev->gso_max_segs = dev->gso_max_segs;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
netdev_features_change(ipvlan->dev);
}
break;
case NETDEV_CHANGEMTU:
list_for_each_entry(ipvlan, &port->ipvlans, pnode)
ipvlan_adjust_mtu(ipvlan, dev);
break;
case NETDEV_CHANGEADDR:
list_for_each_entry(ipvlan, &port->ipvlans, pnode) {
ether_addr_copy(ipvlan->dev->dev_addr, dev->dev_addr);
call_netdevice_notifiers(NETDEV_CHANGEADDR, ipvlan->dev);
}
break;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
case NETDEV_PRE_TYPE_CHANGE:
/* Forbid underlying device to change its type. */
return NOTIFY_BAD;
}
return NOTIFY_DONE;
}
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
/* the caller must held the addrs lock */
static int ipvlan_add_addr(struct ipvl_dev *ipvlan, void *iaddr, bool is_v6)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
struct ipvl_addr *addr;
addr = kzalloc(sizeof(struct ipvl_addr), GFP_ATOMIC);
if (!addr)
return -ENOMEM;
addr->master = ipvlan;
if (!is_v6) {
memcpy(&addr->ip4addr, iaddr, sizeof(struct in_addr));
addr->atype = IPVL_IPV4;
#if IS_ENABLED(CONFIG_IPV6)
} else {
memcpy(&addr->ip6addr, iaddr, sizeof(struct in6_addr));
addr->atype = IPVL_IPV6;
#endif
}
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
list_add_tail_rcu(&addr->anode, &ipvlan->addrs);
/* If the interface is not up, the address will be added to the hash
* list by ipvlan_open.
*/
if (netif_running(ipvlan->dev))
ipvlan_ht_addr_add(ipvlan, addr);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return 0;
}
static void ipvlan_del_addr(struct ipvl_dev *ipvlan, void *iaddr, bool is_v6)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
{
struct ipvl_addr *addr;
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
spin_lock_bh(&ipvlan->addrs_lock);
addr = ipvlan_find_addr(ipvlan, iaddr, is_v6);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
if (!addr) {
spin_unlock_bh(&ipvlan->addrs_lock);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return;
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
ipvlan_ht_addr_del(addr);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
list_del_rcu(&addr->anode);
spin_unlock_bh(&ipvlan->addrs_lock);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
kfree_rcu(addr, rcu);
}
static bool ipvlan_is_valid_dev(const struct net_device *dev)
{
struct ipvl_dev *ipvlan = netdev_priv(dev);
if (!netif_is_ipvlan(dev))
return false;
if (!ipvlan || !ipvlan->port)
return false;
return true;
}
#if IS_ENABLED(CONFIG_IPV6)
static int ipvlan_add_addr6(struct ipvl_dev *ipvlan, struct in6_addr *ip6_addr)
{
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
int ret = -EINVAL;
spin_lock_bh(&ipvlan->addrs_lock);
if (ipvlan_addr_busy(ipvlan->port, ip6_addr, true))
netif_err(ipvlan, ifup, ipvlan->dev,
"Failed to add IPv6=%pI6c addr for %s intf\n",
ip6_addr, ipvlan->dev->name);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
else
ret = ipvlan_add_addr(ipvlan, ip6_addr, true);
spin_unlock_bh(&ipvlan->addrs_lock);
return ret;
}
static void ipvlan_del_addr6(struct ipvl_dev *ipvlan, struct in6_addr *ip6_addr)
{
return ipvlan_del_addr(ipvlan, ip6_addr, true);
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static int ipvlan_addr6_event(struct notifier_block *unused,
unsigned long event, void *ptr)
{
struct inet6_ifaddr *if6 = (struct inet6_ifaddr *)ptr;
struct net_device *dev = (struct net_device *)if6->idev->dev;
struct ipvl_dev *ipvlan = netdev_priv(dev);
if (!ipvlan_is_valid_dev(dev))
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return NOTIFY_DONE;
switch (event) {
case NETDEV_UP:
if (ipvlan_add_addr6(ipvlan, &if6->addr))
return NOTIFY_BAD;
break;
case NETDEV_DOWN:
ipvlan_del_addr6(ipvlan, &if6->addr);
break;
}
return NOTIFY_OK;
}
static int ipvlan_addr6_validator_event(struct notifier_block *unused,
unsigned long event, void *ptr)
{
struct in6_validator_info *i6vi = (struct in6_validator_info *)ptr;
struct net_device *dev = (struct net_device *)i6vi->i6vi_dev->dev;
struct ipvl_dev *ipvlan = netdev_priv(dev);
if (!ipvlan_is_valid_dev(dev))
return NOTIFY_DONE;
switch (event) {
case NETDEV_UP:
if (ipvlan_addr_busy(ipvlan->port, &i6vi->i6vi_addr, true)) {
NL_SET_ERR_MSG(i6vi->extack,
"Address already assigned to an ipvlan device");
return notifier_from_errno(-EADDRINUSE);
}
break;
}
return NOTIFY_OK;
}
#endif
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static int ipvlan_add_addr4(struct ipvl_dev *ipvlan, struct in_addr *ip4_addr)
{
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
int ret = -EINVAL;
spin_lock_bh(&ipvlan->addrs_lock);
if (ipvlan_addr_busy(ipvlan->port, ip4_addr, false))
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
netif_err(ipvlan, ifup, ipvlan->dev,
"Failed to add IPv4=%pI4 on %s intf.\n",
ip4_addr, ipvlan->dev->name);
ipvlan: use per device spinlock to protect addrs list updates This changeset moves ipvlan address under RCU protection, using a per ipvlan device spinlock to protect list mutation and RCU read access to protect list traversal. Also explicitly use RCU read lock to traverse the per port ipvlans list, so that we can now perform a full address lookup without asserting the RTNL lock. Overall this allows the ipvlan driver to check fully for duplicate addresses - before this commit ipv6 addresses assigned by autoconf via prefix delegation where accepted without any check - and avoid the following rntl assertion failure still in the same code path: RTNL: assertion failed at drivers/net/ipvlan/ipvlan_core.c (124) WARNING: CPU: 15 PID: 0 at drivers/net/ipvlan/ipvlan_core.c:124 ipvlan_addr_busy+0x97/0xa0 [ipvlan] Modules linked in: ipvlan(E) ixgbe CPU: 15 PID: 0 Comm: swapper/15 Tainted: G E 4.16.0-rc2.ipvlan+ #1782 Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016 RIP: 0010:ipvlan_addr_busy+0x97/0xa0 [ipvlan] RSP: 0018:ffff881ff9e03768 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff881fdf2a9000 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff881fdf2a8000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: ffff881ff9e034c0 R12: ffff881fe07bcc00 R13: 0000000000000001 R14: ffffffffa02002b0 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff881ff9e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fc5c1a4f248 CR3: 000000207e012005 CR4: 00000000001606e0 Call Trace: <IRQ> ipvlan_addr6_event+0x6c/0xd0 [ipvlan] notifier_call_chain+0x49/0x90 atomic_notifier_call_chain+0x6a/0x100 ipv6_add_addr+0x5f9/0x720 addrconf_prefix_rcv_add_addr+0x244/0x3c0 addrconf_prefix_rcv+0x2f3/0x790 ndisc_router_discovery+0x633/0xb70 ndisc_rcv+0x155/0x180 icmpv6_rcv+0x4ac/0x5f0 ip6_input_finish+0x138/0x6a0 ip6_input+0x41/0x1f0 ipv6_rcv+0x4db/0x8d0 __netif_receive_skb_core+0x3d5/0xe40 netif_receive_skb_internal+0x89/0x370 napi_gro_receive+0x14f/0x1e0 ixgbe_clean_rx_irq+0x4ce/0x1020 [ixgbe] ixgbe_poll+0x31a/0x7a0 [ixgbe] net_rx_action+0x296/0x4f0 __do_softirq+0xcf/0x4f5 irq_exit+0xf5/0x110 do_IRQ+0x62/0x110 common_interrupt+0x91/0x91 </IRQ> v1 -> v2: drop unneeded in_softirq check in ipvlan_addr6_validator_event() Fixes: e9997c2938b2 ("ipvlan: fix check for IP addresses in control path") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-28 16:59:27 +07:00
else
ret = ipvlan_add_addr(ipvlan, ip4_addr, false);
spin_unlock_bh(&ipvlan->addrs_lock);
return ret;
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
static void ipvlan_del_addr4(struct ipvl_dev *ipvlan, struct in_addr *ip4_addr)
{
return ipvlan_del_addr(ipvlan, ip4_addr, false);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
static int ipvlan_addr4_event(struct notifier_block *unused,
unsigned long event, void *ptr)
{
struct in_ifaddr *if4 = (struct in_ifaddr *)ptr;
struct net_device *dev = (struct net_device *)if4->ifa_dev->dev;
struct ipvl_dev *ipvlan = netdev_priv(dev);
struct in_addr ip4_addr;
if (!ipvlan_is_valid_dev(dev))
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return NOTIFY_DONE;
switch (event) {
case NETDEV_UP:
ip4_addr.s_addr = if4->ifa_address;
if (ipvlan_add_addr4(ipvlan, &ip4_addr))
return NOTIFY_BAD;
break;
case NETDEV_DOWN:
ip4_addr.s_addr = if4->ifa_address;
ipvlan_del_addr4(ipvlan, &ip4_addr);
break;
}
return NOTIFY_OK;
}
static int ipvlan_addr4_validator_event(struct notifier_block *unused,
unsigned long event, void *ptr)
{
struct in_validator_info *ivi = (struct in_validator_info *)ptr;
struct net_device *dev = (struct net_device *)ivi->ivi_dev->dev;
struct ipvl_dev *ipvlan = netdev_priv(dev);
if (!ipvlan_is_valid_dev(dev))
return NOTIFY_DONE;
switch (event) {
case NETDEV_UP:
if (ipvlan_addr_busy(ipvlan->port, &ivi->ivi_addr, false)) {
NL_SET_ERR_MSG(ivi->extack,
"Address already assigned to an ipvlan device");
return notifier_from_errno(-EADDRINUSE);
}
break;
}
return NOTIFY_OK;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static struct notifier_block ipvlan_addr4_notifier_block __read_mostly = {
.notifier_call = ipvlan_addr4_event,
};
static struct notifier_block ipvlan_addr4_vtor_notifier_block __read_mostly = {
.notifier_call = ipvlan_addr4_validator_event,
};
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static struct notifier_block ipvlan_notifier_block __read_mostly = {
.notifier_call = ipvlan_device_event,
};
#if IS_ENABLED(CONFIG_IPV6)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static struct notifier_block ipvlan_addr6_notifier_block __read_mostly = {
.notifier_call = ipvlan_addr6_event,
};
static struct notifier_block ipvlan_addr6_vtor_notifier_block __read_mostly = {
.notifier_call = ipvlan_addr6_validator_event,
};
#endif
static void ipvlan_ns_exit(struct net *net)
{
struct ipvlan_netns *vnet = net_generic(net, ipvlan_netid);
if (WARN_ON_ONCE(vnet->ipvl_nf_hook_refcnt)) {
vnet->ipvl_nf_hook_refcnt = 0;
nf_unregister_net_hooks(net, ipvl_nfops,
ARRAY_SIZE(ipvl_nfops));
}
}
static struct pernet_operations ipvlan_net_ops = {
.id = &ipvlan_netid,
.size = sizeof(struct ipvlan_netns),
.exit = ipvlan_ns_exit,
};
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
static int __init ipvlan_init_module(void)
{
int err;
ipvlan_init_secret();
register_netdevice_notifier(&ipvlan_notifier_block);
#if IS_ENABLED(CONFIG_IPV6)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
register_inet6addr_notifier(&ipvlan_addr6_notifier_block);
register_inet6addr_validator_notifier(
&ipvlan_addr6_vtor_notifier_block);
#endif
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
register_inetaddr_notifier(&ipvlan_addr4_notifier_block);
register_inetaddr_validator_notifier(&ipvlan_addr4_vtor_notifier_block);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
err = register_pernet_subsys(&ipvlan_net_ops);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
if (err < 0)
goto error;
err = ipvlan_link_register(&ipvlan_link_ops);
if (err < 0) {
unregister_pernet_subsys(&ipvlan_net_ops);
goto error;
}
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
return 0;
error:
unregister_inetaddr_notifier(&ipvlan_addr4_notifier_block);
unregister_inetaddr_validator_notifier(
&ipvlan_addr4_vtor_notifier_block);
#if IS_ENABLED(CONFIG_IPV6)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
unregister_inet6addr_notifier(&ipvlan_addr6_notifier_block);
unregister_inet6addr_validator_notifier(
&ipvlan_addr6_vtor_notifier_block);
#endif
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
unregister_netdevice_notifier(&ipvlan_notifier_block);
return err;
}
static void __exit ipvlan_cleanup_module(void)
{
rtnl_link_unregister(&ipvlan_link_ops);
unregister_pernet_subsys(&ipvlan_net_ops);
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
unregister_netdevice_notifier(&ipvlan_notifier_block);
unregister_inetaddr_notifier(&ipvlan_addr4_notifier_block);
unregister_inetaddr_validator_notifier(
&ipvlan_addr4_vtor_notifier_block);
#if IS_ENABLED(CONFIG_IPV6)
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
unregister_inet6addr_notifier(&ipvlan_addr6_notifier_block);
unregister_inet6addr_validator_notifier(
&ipvlan_addr6_vtor_notifier_block);
#endif
ipvlan: Initial check-in of the IPVLAN driver. This driver is very similar to the macvlan driver except that it uses L3 on the frame to determine the logical interface while functioning as packet dispatcher. It inherits L2 of the master device hence the packets on wire will have the same L2 for all the packets originating from all virtual devices off of the same master device. This driver was developed keeping the namespace use-case in mind. Hence most of the examples given here take that as the base setup where main-device belongs to the default-ns and virtual devices are assigned to the additional namespaces. The device operates in two different modes and the difference in these two modes in primarily in the TX side. (a) L2 mode : In this mode, the device behaves as a L2 device. TX processing upto L2 happens on the stack of the virtual device associated with (namespace). Packets are switched after that into the main device (default-ns) and queued for xmit. RX processing is simple and all multicast, broadcast (if applicable), and unicast belonging to the address(es) are delivered to the virtual devices. (b) L3 mode : In this mode, the device behaves like a L3 device. TX processing upto L3 happens on the stack of the virtual device associated with (namespace). Packets are switched to the main-device (default-ns) for the L2 processing. Hence the routing table of the default-ns will be used in this mode. RX processins is somewhat similar to the L2 mode except that in this mode only Unicast packets are delivered to the virtual device while main-dev will handle all other packets. The devices can be added using the "ip" command from the iproute2 package - ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ] Signed-off-by: Mahesh Bandewar <maheshb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Laurent Chavey <chavey@google.com> Cc: Tim Hockin <thockin@google.com> Cc: Brandon Philips <brandon.philips@coreos.com> Cc: Pavel Emelianov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-24 14:07:46 +07:00
}
module_init(ipvlan_init_module);
module_exit(ipvlan_cleanup_module);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Mahesh Bandewar <maheshb@google.com>");
MODULE_DESCRIPTION("Driver for L3 (IPv6/IPv4) based VLANs");
MODULE_ALIAS_RTNL_LINK("ipvlan");