linux_dsm_epyc7002/drivers/pinctrl/berlin/Kconfig

if (ARCH_BERLIN || COMPILE_TEST)

config PINCTRL_BERLIN
	bool
	select PINMUX
	select REGMAP_MMIO

config PINCTRL_BERLIN_BG2
	bool
	select PINCTRL_BERLIN

config PINCTRL_BERLIN_BG2CD
	bool
	select PINCTRL_BERLIN

config PINCTRL_BERLIN_BG2Q
	bool
	select PINCTRL_BERLIN

endif
pinctrl: berlin: Make berlin pinctrl driver visible if COMPILE_TEST=y It is good to allow berlin pinctrl driver to build with COMPILE_TEST, so make the it menu visible when compile-testing. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2015-10-16 14:37:07 +07:00			`if (ARCH_BERLIN \|\| COMPILE_TEST)`
pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs The Marvell Berlin boards have a group based pinmuxing mechanism. This adds the core driver support. We actually do not need any information about the pins here and only have the definition of the groups. Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set to mode 0: Group Modes Offset Base Offset LSB Bit Width GSM12 3 sm_base 0x40 0x10 0x2 Ball Group Mode 0 Mode 1 Mode 2 BK4 GSM12 UART0_RX IrDA0_RX GPIO9 BH6 GSM12 UART0_TX IrDA0_TX GPIO10 So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need to set (sm_base + 0x40 + 0x10) &= ff3fffff. As pin control registers are part of either chip control or system control registers, that deal with a bunch of other functions we rely on a regmap instead of exclusively remapping any resources. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2014-05-20 00:36:29 +07:00
			`config PINCTRL_BERLIN`
			`bool`
			`select PINMUX`
			`select REGMAP_MMIO`

pinctrl: berlin: add the BG2 pinctrl driver Add the pin-controller driver for the Berlin BG2 SoC, with definition of its groups and functions. Pin control registers are part of chip/ system control registers, which will be represented by a single node. Until a proper driver for the chip/system control is available, register the corresponding regmap in pinctrl driver probe. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2014-05-20 00:36:31 +07:00			`config PINCTRL_BERLIN_BG2`
			`bool`
			`select PINCTRL_BERLIN`

pinctrl: berlin: add the BG2CD pinctrl driver Add the pin-controller driver for the Berlin BG2Q SoC, with definition of its groups and functions. Pin control registers are part of chip/ system control registers, which will be represented by a single node. Until a proper driver for the chip/system control is available, register the corresponding regmap in pinctrl driver probe. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2014-05-20 00:36:32 +07:00			`config PINCTRL_BERLIN_BG2CD`
			`bool`
			`select PINCTRL_BERLIN`

pinctrl: berlin: add the BG2Q pinctrl driver Add the pin-controller driver for the Berlin BG2Q SoC, with definition of its groups and functions. Pin control registers are part of chip/ system control registers, which will be represented by a single node. Until a proper driver for the chip/system control is available, register the corresponding regmap in pinctrl driver probe. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2014-05-20 00:36:30 +07:00			`config PINCTRL_BERLIN_BG2Q`
			`bool`
			`select PINCTRL_BERLIN`

pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs The Marvell Berlin boards have a group based pinmuxing mechanism. This adds the core driver support. We actually do not need any information about the pins here and only have the definition of the groups. Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set to mode 0: Group Modes Offset Base Offset LSB Bit Width GSM12 3 sm_base 0x40 0x10 0x2 Ball Group Mode 0 Mode 1 Mode 2 BK4 GSM12 UART0_RX IrDA0_RX GPIO9 BH6 GSM12 UART0_TX IrDA0_TX GPIO10 So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need to set (sm_base + 0x40 + 0x10) &= ff3fffff. As pin control registers are part of either chip control or system control registers, that deal with a bunch of other functions we rely on a regmap instead of exclusively remapping any resources. Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 2014-05-20 00:36:29 +07:00			`endif`