linux_dsm_epyc7002/drivers/net/wireless/wl12xx/wl1271_main.c

2087 lines
49 KiB
C
Raw Normal View History

/*
* This file is part of wl1271
*
* Copyright (C) 2008-2009 Nokia Corporation
*
* Contact: Luciano Coelho <luciano.coelho@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/firmware.h>
#include <linux/delay.h>
#include <linux/irq.h>
#include <linux/spi/spi.h>
#include <linux/crc32.h>
#include <linux/etherdevice.h>
#include <linux/vmalloc.h>
#include <linux/spi/wl12xx.h>
#include <linux/inetdevice.h>
#include "wl1271.h"
#include "wl12xx_80211.h"
#include "wl1271_reg.h"
#include "wl1271_spi.h"
#include "wl1271_event.h"
#include "wl1271_tx.h"
#include "wl1271_rx.h"
#include "wl1271_ps.h"
#include "wl1271_init.h"
#include "wl1271_debugfs.h"
#include "wl1271_cmd.h"
#include "wl1271_boot.h"
#define WL1271_BOOT_RETRIES 3
static struct conf_drv_settings default_conf = {
.sg = {
.per_threshold = 7500,
.max_scan_compensation_time = 120000,
.nfs_sample_interval = 400,
.load_ratio = 50,
.auto_ps_mode = 0,
.probe_req_compensation = 170,
.scan_window_compensation = 50,
.antenna_config = 0,
.beacon_miss_threshold = 60,
.rate_adaptation_threshold = CONF_HW_BIT_RATE_12MBPS,
.rate_adaptation_snr = 0
},
.rx = {
.rx_msdu_life_time = 512000,
.packet_detection_threshold = 0,
.ps_poll_timeout = 15,
.upsd_timeout = 15,
.rts_threshold = 2347,
.rx_cca_threshold = 0,
.irq_blk_threshold = 0xFFFF,
.irq_pkt_threshold = 0,
.irq_timeout = 600,
.queue_type = CONF_RX_QUEUE_TYPE_LOW_PRIORITY,
},
.tx = {
.tx_energy_detection = 0,
.rc_conf = {
.enabled_rates = CONF_TX_RATE_MASK_UNSPECIFIED,
.short_retry_limit = 10,
.long_retry_limit = 10,
.aflags = 0
},
.ac_conf_count = 4,
.ac_conf = {
[0] = {
.ac = CONF_TX_AC_BE,
.cw_min = 15,
.cw_max = 63,
.aifsn = 3,
.tx_op_limit = 0,
},
[1] = {
.ac = CONF_TX_AC_BK,
.cw_min = 15,
.cw_max = 63,
.aifsn = 7,
.tx_op_limit = 0,
},
[2] = {
.ac = CONF_TX_AC_VI,
.cw_min = 15,
.cw_max = 63,
.aifsn = CONF_TX_AIFS_PIFS,
.tx_op_limit = 3008,
},
[3] = {
.ac = CONF_TX_AC_VO,
.cw_min = 15,
.cw_max = 63,
.aifsn = CONF_TX_AIFS_PIFS,
.tx_op_limit = 1504,
},
},
.tid_conf_count = 7,
.tid_conf = {
[0] = {
.queue_id = 0,
.channel_type = CONF_CHANNEL_TYPE_DCF,
.tsid = CONF_TX_AC_BE,
.ps_scheme = CONF_PS_SCHEME_LEGACY,
.ack_policy = CONF_ACK_POLICY_LEGACY,
.apsd_conf = {0, 0},
},
[1] = {
.queue_id = 1,
.channel_type = CONF_CHANNEL_TYPE_DCF,
.tsid = CONF_TX_AC_BE,
.ps_scheme = CONF_PS_SCHEME_LEGACY,
.ack_policy = CONF_ACK_POLICY_LEGACY,
.apsd_conf = {0, 0},
},
[2] = {
.queue_id = 2,
.channel_type = CONF_CHANNEL_TYPE_DCF,
.tsid = CONF_TX_AC_BE,
.ps_scheme = CONF_PS_SCHEME_LEGACY,
.ack_policy = CONF_ACK_POLICY_LEGACY,
.apsd_conf = {0, 0},
},
[3] = {
.queue_id = 3,
.channel_type = CONF_CHANNEL_TYPE_DCF,
.tsid = CONF_TX_AC_BE,
.ps_scheme = CONF_PS_SCHEME_LEGACY,
.ack_policy = CONF_ACK_POLICY_LEGACY,
.apsd_conf = {0, 0},
},
[4] = {
.queue_id = 4,
.channel_type = CONF_CHANNEL_TYPE_DCF,
.tsid = CONF_TX_AC_BE,
.ps_scheme = CONF_PS_SCHEME_LEGACY,
.ack_policy = CONF_ACK_POLICY_LEGACY,
.apsd_conf = {0, 0},
},
[5] = {
.queue_id = 5,
.channel_type = CONF_CHANNEL_TYPE_DCF,
.tsid = CONF_TX_AC_BE,
.ps_scheme = CONF_PS_SCHEME_LEGACY,
.ack_policy = CONF_ACK_POLICY_LEGACY,
.apsd_conf = {0, 0},
},
[6] = {
.queue_id = 6,
.channel_type = CONF_CHANNEL_TYPE_DCF,
.tsid = CONF_TX_AC_BE,
.ps_scheme = CONF_PS_SCHEME_LEGACY,
.ack_policy = CONF_ACK_POLICY_LEGACY,
.apsd_conf = {0, 0},
}
},
.frag_threshold = IEEE80211_MAX_FRAG_THRESHOLD,
.tx_compl_timeout = 700,
.tx_compl_threshold = 4
},
.conn = {
.wake_up_event = CONF_WAKE_UP_EVENT_DTIM,
.listen_interval = 0,
.bcn_filt_mode = CONF_BCN_FILT_MODE_ENABLED,
.bcn_filt_ie_count = 1,
.bcn_filt_ie = {
[0] = {
.ie = WLAN_EID_CHANNEL_SWITCH,
.rule = CONF_BCN_RULE_PASS_ON_APPEARANCE,
}
},
.synch_fail_thold = 10,
.bss_lose_timeout = 100,
.beacon_rx_timeout = 10000,
.broadcast_timeout = 20000,
.rx_broadcast_in_ps = 1,
.ps_poll_threshold = 20,
.sig_trigger_count = 2,
.sig_trigger = {
[0] = {
.threshold = -75,
.pacing = 500,
.metric = CONF_TRIG_METRIC_RSSI_BEACON,
.type = CONF_TRIG_EVENT_TYPE_EDGE,
.direction = CONF_TRIG_EVENT_DIR_LOW,
.hysteresis = 2,
.index = 0,
.enable = 1
},
[1] = {
.threshold = -75,
.pacing = 500,
.metric = CONF_TRIG_METRIC_RSSI_BEACON,
.type = CONF_TRIG_EVENT_TYPE_EDGE,
.direction = CONF_TRIG_EVENT_DIR_HIGH,
.hysteresis = 2,
.index = 1,
.enable = 1
}
},
.sig_weights = {
.rssi_bcn_avg_weight = 10,
.rssi_pkt_avg_weight = 10,
.snr_bcn_avg_weight = 10,
.snr_pkt_avg_weight = 10
},
.bet_enable = CONF_BET_MODE_ENABLE,
.bet_max_consecutive = 10,
.psm_entry_retries = 3
},
.init = {
.genparam = {
.ref_clk = CONF_REF_CLK_38_4_E,
.settling_time = 5,
.clk_valid_on_wakeup = 0,
.dc2dcmode = 0,
.single_dual_band = CONF_SINGLE_BAND,
.tx_bip_fem_autodetect = 1,
.tx_bip_fem_manufacturer = 1,
.settings = 1,
.sr_state = 1,
.srf1 = { 0x07, 0x03, 0x18, 0x10, 0x05, 0xfb, 0xf0,
0xe8, 0, 0, 0, 0, 0, 0, 0, 0 },
.srf2 = { 0x07, 0x03, 0x18, 0x10, 0x05, 0xfb, 0xf0,
0xe8, 0, 0, 0, 0, 0, 0, 0, 0 },
.srf3 = { 0x07, 0x03, 0x18, 0x10, 0x05, 0xfb, 0xf0,
0xe8, 0, 0, 0, 0, 0, 0, 0, 0 },
.sr_debug_table = { 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0 },
.sr_sen_n_p = 0,
.sr_sen_n_p_gain = 0,
.sr_sen_nrn = 0,
.sr_sen_prn = 0,
},
.radioparam = {
.rx_trace_loss = 0x24,
.tx_trace_loss = 0x0,
.rx_rssi_and_proc_compens = {
0xec, 0xf6, 0x00, 0x0c, 0x18, 0xf8,
0xfc, 0x00, 0x80, 0x10, 0xf0, 0xf8,
0x00, 0x0a, 0x14 },
.rx_trace_loss_5 = { 0, 0, 0, 0, 0, 0, 0 },
.tx_trace_loss_5 = { 0, 0, 0, 0, 0, 0, 0 },
.rx_rssi_and_proc_compens_5 = {
0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00 },
.tx_ref_pd_voltage = 0x1a9,
.tx_ref_power = 0x80,
.tx_offset_db = 0x0,
.tx_rate_limits_normal = {
0x1d, 0x1f, 0x24, 0x28, 0x28, 0x29 },
.tx_rate_limits_degraded = {
0x19, 0x1f, 0x22, 0x23, 0x27, 0x28 },
.tx_rate_limits_extreme = {
0x19, 0x1c, 0x1e, 0x20, 0x24, 0x25 },
.tx_channel_limits_11b = {
0x22, 0x50, 0x50, 0x50, 0x50, 0x50,
0x50, 0x50, 0x50, 0x50, 0x22, 0x50,
0x22, 0x50 },
.tx_channel_limits_ofdm = {
0x20, 0x50, 0x50, 0x50, 0x50, 0x50,
0x50, 0x50, 0x50, 0x50, 0x20, 0x50,
0x20, 0x50 },
.tx_pdv_rate_offsets = {
0x07, 0x08, 0x04, 0x02, 0x02, 0x00 },
.tx_ibias = {
0x11, 0x11, 0x15, 0x11, 0x15, 0x0f },
.rx_fem_insertion_loss = 0x0e,
.degraded_low_to_normal_threshold = 0x1e,
.degraded_normal_to_high_threshold = 0x2d,
.tx_ref_pd_voltage_5 = {
0x0190, 0x01a4, 0x01c3, 0x01d8,
0x020a, 0x021c },
.tx_ref_power_5 = {
0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80 },
.tx_offset_db_5 = {
0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },
.tx_rate_limits_normal_5 = {
0x1b, 0x1e, 0x21, 0x23, 0x27, 0x00 },
.tx_rate_limits_degraded_5 = {
0x1b, 0x1e, 0x21, 0x23, 0x27, 0x00 },
.tx_rate_limits_extreme_5 = {
0x1b, 0x1e, 0x21, 0x23, 0x27, 0x00 },
.tx_channel_limits_ofdm_5 = {
0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50,
0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50,
0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50,
0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50, 0x50,
0x50, 0x50, 0x50 },
.tx_pdv_rate_offsets_5 = {
0x01, 0x02, 0x02, 0x02, 0x02, 0x00 },
.tx_ibias_5 = {
0x10, 0x10, 0x10, 0x10, 0x10, 0x10 },
.rx_fem_insertion_loss_5 = {
0x10, 0x10, 0x10, 0x10, 0x10, 0x10, 0x10 },
.degraded_low_to_normal_threshold_5 = 0x00,
.degraded_normal_to_high_threshold_5 = 0x00
}
},
.itrim = {
.enable = false,
.timeout = 50000,
}
};
static LIST_HEAD(wl_list);
static void wl1271_conf_init(struct wl1271 *wl)
{
/*
* This function applies the default configuration to the driver. This
* function is invoked upon driver load (spi probe.)
*
* The configuration is stored in a run-time structure in order to
* facilitate for run-time adjustment of any of the parameters. Making
* changes to the configuration structure will apply the new values on
* the next interface up (wl1271_op_start.)
*/
/* apply driver default configuration */
memcpy(&wl->conf, &default_conf, sizeof(default_conf));
if (wl1271_11a_enabled())
wl->conf.init.genparam.single_dual_band = CONF_DUAL_BAND;
}
static int wl1271_plt_init(struct wl1271 *wl)
{
int ret;
ret = wl1271_cmd_general_parms(wl);
if (ret < 0)
return ret;
ret = wl1271_cmd_radio_parms(wl);
if (ret < 0)
return ret;
ret = wl1271_acx_init_mem_config(wl);
if (ret < 0)
return ret;
ret = wl1271_cmd_data_path(wl, 1);
if (ret < 0)
return ret;
return 0;
}
static void wl1271_disable_interrupts(struct wl1271 *wl)
{
disable_irq(wl->irq);
}
static void wl1271_power_off(struct wl1271 *wl)
{
wl->set_power(false);
wl->gpio_power = false;
}
static void wl1271_power_on(struct wl1271 *wl)
{
wl->set_power(true);
wl->gpio_power = true;
}
static void wl1271_fw_status(struct wl1271 *wl,
struct wl1271_fw_status *status)
{
u32 total = 0;
int i;
wl1271_spi_read(wl, FW_STATUS_ADDR, status,
sizeof(*status), false);
wl1271_debug(DEBUG_IRQ, "intr: 0x%x (fw_rx_counter = %d, "
"drv_rx_counter = %d, tx_results_counter = %d)",
status->intr,
status->fw_rx_counter,
status->drv_rx_counter,
status->tx_results_counter);
/* update number of available TX blocks */
for (i = 0; i < NUM_TX_QUEUES; i++) {
wl1271: fix endianess issues We were not handling endianess correctly. The wl1271 chip runs on little-endian values. This patch makes sure that all the communication with the wl1271 firmware is done in little-endian by using cpu_to_le* and le*_to_cpu where appropriate. Also, all the struct definitions for data exchanged with the firmware has been changed to use __le16/32 types instead of u16/32. This fixes a few sparse warnings, such as these: drivers/net/wireless/wl12xx/wl1271_cmd.c:554:42: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:555:42: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:577:58: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:579:58: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:676:18: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:787:22: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:789:21: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_tx.c:98:47: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_acx.c:932:32: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:191:32: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:197:38: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:199:37: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_init.c:255:40: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_init.c:275:53: warning: incorrect type in assignment (different base types) Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-15 14:33:29 +07:00
u32 cnt = le32_to_cpu(status->tx_released_blks[i]) -
wl->tx_blocks_freed[i];
wl->tx_blocks_freed[i] =
le32_to_cpu(status->tx_released_blks[i]);
wl->tx_blocks_available += cnt;
total += cnt;
}
/* if more blocks are available now, schedule some tx work */
if (total && !skb_queue_empty(&wl->tx_queue))
ieee80211_queue_work(wl->hw, &wl->tx_work);
/* update the host-chipset time offset */
wl1271: fix endianess issues We were not handling endianess correctly. The wl1271 chip runs on little-endian values. This patch makes sure that all the communication with the wl1271 firmware is done in little-endian by using cpu_to_le* and le*_to_cpu where appropriate. Also, all the struct definitions for data exchanged with the firmware has been changed to use __le16/32 types instead of u16/32. This fixes a few sparse warnings, such as these: drivers/net/wireless/wl12xx/wl1271_cmd.c:554:42: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:555:42: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:577:58: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:579:58: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:676:18: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:787:22: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:789:21: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_tx.c:98:47: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_acx.c:932:32: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:191:32: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:197:38: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:199:37: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_init.c:255:40: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_init.c:275:53: warning: incorrect type in assignment (different base types) Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-15 14:33:29 +07:00
wl->time_offset = jiffies_to_usecs(jiffies) -
le32_to_cpu(status->fw_localtime);
}
static void wl1271_irq_work(struct work_struct *work)
{
int ret;
u32 intr;
struct wl1271 *wl =
container_of(work, struct wl1271, irq_work);
mutex_lock(&wl->mutex);
wl1271_debug(DEBUG_IRQ, "IRQ work");
if (wl->state == WL1271_STATE_OFF)
goto out;
ret = wl1271_ps_elp_wakeup(wl, true);
if (ret < 0)
goto out;
wl1271_spi_write32(wl, ACX_REG_INTERRUPT_MASK, WL1271_ACX_INTR_ALL);
wl1271_fw_status(wl, wl->fw_status);
wl1271: fix endianess issues We were not handling endianess correctly. The wl1271 chip runs on little-endian values. This patch makes sure that all the communication with the wl1271 firmware is done in little-endian by using cpu_to_le* and le*_to_cpu where appropriate. Also, all the struct definitions for data exchanged with the firmware has been changed to use __le16/32 types instead of u16/32. This fixes a few sparse warnings, such as these: drivers/net/wireless/wl12xx/wl1271_cmd.c:554:42: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:555:42: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:577:58: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:579:58: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:676:18: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:787:22: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_cmd.c:789:21: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_tx.c:98:47: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_acx.c:932:32: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:191:32: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:197:38: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_boot.c:199:37: warning: incorrect type in argument 1 (different base types) drivers/net/wireless/wl12xx/wl1271_init.c:255:40: warning: incorrect type in assignment (different base types) drivers/net/wireless/wl12xx/wl1271_init.c:275:53: warning: incorrect type in assignment (different base types) Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-15 14:33:29 +07:00
intr = le32_to_cpu(wl->fw_status->intr);
if (!intr) {
wl1271_debug(DEBUG_IRQ, "Zero interrupt received.");
goto out_sleep;
}
intr &= WL1271_INTR_MASK;
if (intr & WL1271_ACX_INTR_EVENT_A) {
wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_EVENT_A");
wl1271_event_handle(wl, 0);
}
if (intr & WL1271_ACX_INTR_EVENT_B) {
wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_EVENT_B");
wl1271_event_handle(wl, 1);
}
if (intr & WL1271_ACX_INTR_INIT_COMPLETE)
wl1271_debug(DEBUG_IRQ,
"WL1271_ACX_INTR_INIT_COMPLETE");
if (intr & WL1271_ACX_INTR_HW_AVAILABLE)
wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_HW_AVAILABLE");
if (intr & WL1271_ACX_INTR_DATA) {
u8 tx_res_cnt = wl->fw_status->tx_results_counter -
wl->tx_results_count;
wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_DATA");
/* check for tx results */
if (tx_res_cnt)
wl1271_tx_complete(wl, tx_res_cnt);
wl1271_rx(wl, wl->fw_status);
}
out_sleep:
wl1271_spi_write32(wl, ACX_REG_INTERRUPT_MASK,
WL1271_ACX_INTR_ALL & ~(WL1271_INTR_MASK));
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
}
static irqreturn_t wl1271_irq(int irq, void *cookie)
{
struct wl1271 *wl;
unsigned long flags;
wl1271_debug(DEBUG_IRQ, "IRQ");
wl = cookie;
/* complete the ELP completion */
spin_lock_irqsave(&wl->wl_lock, flags);
if (wl->elp_compl) {
complete(wl->elp_compl);
wl->elp_compl = NULL;
}
ieee80211_queue_work(wl->hw, &wl->irq_work);
spin_unlock_irqrestore(&wl->wl_lock, flags);
return IRQ_HANDLED;
}
static int wl1271_fetch_firmware(struct wl1271 *wl)
{
const struct firmware *fw;
int ret;
ret = request_firmware(&fw, WL1271_FW_NAME, &wl->spi->dev);
if (ret < 0) {
wl1271_error("could not get firmware: %d", ret);
return ret;
}
if (fw->size % 4) {
wl1271_error("firmware size is not multiple of 32 bits: %zu",
fw->size);
ret = -EILSEQ;
goto out;
}
wl->fw_len = fw->size;
wl->fw = vmalloc(wl->fw_len);
if (!wl->fw) {
wl1271_error("could not allocate memory for the firmware");
ret = -ENOMEM;
goto out;
}
memcpy(wl->fw, fw->data, wl->fw_len);
ret = 0;
out:
release_firmware(fw);
return ret;
}
static int wl1271_fetch_nvs(struct wl1271 *wl)
{
const struct firmware *fw;
int ret;
ret = request_firmware(&fw, WL1271_NVS_NAME, &wl->spi->dev);
if (ret < 0) {
wl1271_error("could not get nvs file: %d", ret);
return ret;
}
if (fw->size % 4) {
wl1271_error("nvs size is not multiple of 32 bits: %zu",
fw->size);
ret = -EILSEQ;
goto out;
}
wl->nvs_len = fw->size;
wl->nvs = kmalloc(wl->nvs_len, GFP_KERNEL);
if (!wl->nvs) {
wl1271_error("could not allocate memory for the nvs file");
ret = -ENOMEM;
goto out;
}
memcpy(wl->nvs, fw->data, wl->nvs_len);
ret = 0;
out:
release_firmware(fw);
return ret;
}
static void wl1271_fw_wakeup(struct wl1271 *wl)
{
u32 elp_reg;
elp_reg = ELPCTRL_WAKE_UP;
wl1271_raw_write32(wl, HW_ACCESS_ELP_CTRL_REG_ADDR, elp_reg);
}
static int wl1271_setup(struct wl1271 *wl)
{
wl->fw_status = kmalloc(sizeof(*wl->fw_status), GFP_KERNEL);
if (!wl->fw_status)
return -ENOMEM;
wl->tx_res_if = kmalloc(sizeof(*wl->tx_res_if), GFP_KERNEL);
if (!wl->tx_res_if) {
kfree(wl->fw_status);
return -ENOMEM;
}
INIT_WORK(&wl->irq_work, wl1271_irq_work);
INIT_WORK(&wl->tx_work, wl1271_tx_work);
return 0;
}
static int wl1271_chip_wakeup(struct wl1271 *wl)
{
struct wl1271_partition_set partition;
int ret = 0;
msleep(WL1271_PRE_POWER_ON_SLEEP);
wl1271_power_on(wl);
msleep(WL1271_POWER_ON_SLEEP);
wl1271_spi_reset(wl);
wl1271_spi_init(wl);
/* We don't need a real memory partition here, because we only want
* to use the registers at this point. */
memset(&partition, 0, sizeof(partition));
partition.reg.start = REGISTERS_BASE;
partition.reg.size = REGISTERS_DOWN_SIZE;
wl1271_set_partition(wl, &partition);
/* ELP module wake up */
wl1271_fw_wakeup(wl);
/* whal_FwCtrl_BootSm() */
/* 0. read chip id from CHIP_ID */
wl->chip.id = wl1271_spi_read32(wl, CHIP_ID_B);
/* 1. check if chip id is valid */
switch (wl->chip.id) {
case CHIP_ID_1271_PG10:
wl1271_warning("chip id 0x%x (1271 PG10) support is obsolete",
wl->chip.id);
ret = wl1271_setup(wl);
if (ret < 0)
goto out;
break;
case CHIP_ID_1271_PG20:
wl1271_debug(DEBUG_BOOT, "chip id 0x%x (1271 PG20)",
wl->chip.id);
ret = wl1271_setup(wl);
if (ret < 0)
goto out;
break;
default:
wl1271_warning("unsupported chip id: 0x%x", wl->chip.id);
ret = -ENODEV;
goto out;
}
if (wl->fw == NULL) {
ret = wl1271_fetch_firmware(wl);
if (ret < 0)
goto out;
}
/* No NVS from netlink, try to get it from the filesystem */
if (wl->nvs == NULL) {
ret = wl1271_fetch_nvs(wl);
if (ret < 0)
goto out;
}
out:
return ret;
}
int wl1271_plt_start(struct wl1271 *wl)
{
int retries = WL1271_BOOT_RETRIES;
int ret;
mutex_lock(&wl->mutex);
wl1271_notice("power up");
if (wl->state != WL1271_STATE_OFF) {
wl1271_error("cannot go into PLT state because not "
"in off state: %d", wl->state);
ret = -EBUSY;
goto out;
}
while (retries) {
retries--;
ret = wl1271_chip_wakeup(wl);
if (ret < 0)
goto power_off;
ret = wl1271_boot(wl);
if (ret < 0)
goto power_off;
ret = wl1271_plt_init(wl);
if (ret < 0)
goto irq_disable;
/* Make sure power saving is disabled */
ret = wl1271_acx_sleep_auth(wl, WL1271_PSM_CAM);
if (ret < 0)
goto irq_disable;
wl->state = WL1271_STATE_PLT;
wl1271_notice("firmware booted in PLT mode (%s)",
wl->chip.fw_ver);
goto out;
irq_disable:
wl1271_disable_interrupts(wl);
mutex_unlock(&wl->mutex);
/* Unlocking the mutex in the middle of handling is
inherently unsafe. In this case we deem it safe to do,
because we need to let any possibly pending IRQ out of
the system (and while we are WL1271_STATE_OFF the IRQ
work function will not do anything.) Also, any other
possible concurrent operations will fail due to the
current state, hence the wl1271 struct should be safe. */
cancel_work_sync(&wl->irq_work);
mutex_lock(&wl->mutex);
power_off:
wl1271_power_off(wl);
}
wl1271_error("firmware boot in PLT mode failed despite %d retries",
WL1271_BOOT_RETRIES);
out:
mutex_unlock(&wl->mutex);
return ret;
}
int wl1271_plt_stop(struct wl1271 *wl)
{
int ret = 0;
mutex_lock(&wl->mutex);
wl1271_notice("power down");
if (wl->state != WL1271_STATE_PLT) {
wl1271_error("cannot power down because not in PLT "
"state: %d", wl->state);
ret = -EBUSY;
goto out;
}
wl1271_disable_interrupts(wl);
wl1271_power_off(wl);
wl->state = WL1271_STATE_OFF;
wl->rx_counter = 0;
out:
mutex_unlock(&wl->mutex);
return ret;
}
static int wl1271_op_tx(struct ieee80211_hw *hw, struct sk_buff *skb)
{
struct wl1271 *wl = hw->priv;
skb_queue_tail(&wl->tx_queue, skb);
/*
* The chip specific setup must run before the first TX packet -
* before that, the tx_work will not be initialized!
*/
ieee80211_queue_work(wl->hw, &wl->tx_work);
/*
* The workqueue is slow to process the tx_queue and we need stop
* the queue here, otherwise the queue will get too long.
*/
if (skb_queue_len(&wl->tx_queue) >= WL1271_TX_QUEUE_MAX_LENGTH) {
ieee80211_stop_queues(wl->hw);
/*
* FIXME: this is racy, the variable is not properly
* protected. Maybe fix this by removing the stupid
* variable altogether and checking the real queue state?
*/
wl->tx_queue_stopped = true;
}
return NETDEV_TX_OK;
}
static int wl1271_dev_notify(struct notifier_block *me, unsigned long what,
void *arg)
{
struct net_device *dev;
struct wireless_dev *wdev;
struct wiphy *wiphy;
struct ieee80211_hw *hw;
struct wl1271 *wl;
struct wl1271 *wl_temp;
struct in_device *idev;
struct in_ifaddr *ifa = arg;
int ret = 0;
/* FIXME: this ugly function should probably be implemented in the
* mac80211, and here should only be a simple callback handling actual
* setting of the filters. Now we need to dig up references to
* various structures to gain access to what we need.
* Also, because of this, there is no "initial" setting of the filter
* in "op_start", because we don't want to dig up struct net_device
* there - the filter will be set upon first change of the interface
* IP address. */
dev = ifa->ifa_dev->dev;
wdev = dev->ieee80211_ptr;
if (wdev == NULL)
return NOTIFY_DONE;
wiphy = wdev->wiphy;
if (wiphy == NULL)
return NOTIFY_DONE;
hw = wiphy_priv(wiphy);
if (hw == NULL)
return NOTIFY_DONE;
/* Check that the interface is one supported by this driver. */
wl_temp = hw->priv;
list_for_each_entry(wl, &wl_list, list) {
if (wl == wl_temp)
break;
}
if (wl == NULL)
return NOTIFY_DONE;
/* Get the interface IP address for the device. "ifa" will become
NULL if:
- there is no IPV4 protocol address configured
- there are multiple (virtual) IPV4 addresses configured
When "ifa" is NULL, filtering will be disabled.
*/
ifa = NULL;
idev = dev->ip_ptr;
if (idev)
ifa = idev->ifa_list;
if (ifa && ifa->ifa_next)
ifa = NULL;
mutex_lock(&wl->mutex);
if (wl->state == WL1271_STATE_OFF)
goto out;
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out;
if (ifa)
ret = wl1271_acx_arp_ip_filter(wl, true,
(u8 *)&ifa->ifa_address,
ACX_IPV4_VERSION);
else
ret = wl1271_acx_arp_ip_filter(wl, false, NULL,
ACX_IPV4_VERSION);
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
return NOTIFY_OK;
}
static struct notifier_block wl1271_dev_notifier = {
.notifier_call = wl1271_dev_notify,
};
static int wl1271_op_start(struct ieee80211_hw *hw)
{
struct wl1271 *wl = hw->priv;
int retries = WL1271_BOOT_RETRIES;
int ret = 0;
wl1271_debug(DEBUG_MAC80211, "mac80211 start");
mutex_lock(&wl->mutex);
if (wl->state != WL1271_STATE_OFF) {
wl1271_error("cannot start because not in off state: %d",
wl->state);
ret = -EBUSY;
goto out;
}
while (retries) {
retries--;
ret = wl1271_chip_wakeup(wl);
if (ret < 0)
goto power_off;
ret = wl1271_boot(wl);
if (ret < 0)
goto power_off;
ret = wl1271_hw_init(wl);
if (ret < 0)
goto irq_disable;
wl->state = WL1271_STATE_ON;
wl1271_info("firmware booted (%s)", wl->chip.fw_ver);
goto out;
irq_disable:
wl1271_disable_interrupts(wl);
mutex_unlock(&wl->mutex);
/* Unlocking the mutex in the middle of handling is
inherently unsafe. In this case we deem it safe to do,
because we need to let any possibly pending IRQ out of
the system (and while we are WL1271_STATE_OFF the IRQ
work function will not do anything.) Also, any other
possible concurrent operations will fail due to the
current state, hence the wl1271 struct should be safe. */
cancel_work_sync(&wl->irq_work);
mutex_lock(&wl->mutex);
power_off:
wl1271_power_off(wl);
}
wl1271_error("firmware boot failed despite %d retries",
WL1271_BOOT_RETRIES);
out:
mutex_unlock(&wl->mutex);
if (!ret) {
list_add(&wl->list, &wl_list);
register_inetaddr_notifier(&wl1271_dev_notifier);
}
return ret;
}
static void wl1271_op_stop(struct ieee80211_hw *hw)
{
struct wl1271 *wl = hw->priv;
int i;
wl1271_info("down");
wl1271_debug(DEBUG_MAC80211, "mac80211 stop");
unregister_inetaddr_notifier(&wl1271_dev_notifier);
list_del(&wl->list);
mutex_lock(&wl->mutex);
WARN_ON(wl->state != WL1271_STATE_ON);
if (wl->scanning) {
mutex_unlock(&wl->mutex);
ieee80211_scan_completed(wl->hw, true);
mutex_lock(&wl->mutex);
wl->scanning = false;
}
wl->state = WL1271_STATE_OFF;
wl1271_disable_interrupts(wl);
mutex_unlock(&wl->mutex);
cancel_work_sync(&wl->irq_work);
cancel_work_sync(&wl->tx_work);
mutex_lock(&wl->mutex);
/* let's notify MAC80211 about the remaining pending TX frames */
wl1271_tx_flush(wl);
wl1271_power_off(wl);
memset(wl->bssid, 0, ETH_ALEN);
memset(wl->ssid, 0, IW_ESSID_MAX_SIZE + 1);
wl->ssid_len = 0;
wl->bss_type = MAX_BSS_TYPE;
wl->band = IEEE80211_BAND_2GHZ;
wl->rx_counter = 0;
wl->elp = false;
wl->psm = 0;
wl->psm_entry_retry = 0;
wl->associated = false;
wl->tx_queue_stopped = false;
wl->power_level = WL1271_DEFAULT_POWER_LEVEL;
wl->tx_blocks_available = 0;
wl->tx_results_count = 0;
wl->tx_packets_count = 0;
wl->tx_security_last_seq = 0;
wl->tx_security_seq_16 = 0;
wl->tx_security_seq_32 = 0;
wl->time_offset = 0;
wl->session_counter = 0;
wl->joined = false;
for (i = 0; i < NUM_TX_QUEUES; i++)
wl->tx_blocks_freed[i] = 0;
wl1271_debugfs_reset(wl);
mutex_unlock(&wl->mutex);
}
static int wl1271_op_add_interface(struct ieee80211_hw *hw,
struct ieee80211_if_init_conf *conf)
{
struct wl1271 *wl = hw->priv;
int ret = 0;
wl1271_debug(DEBUG_MAC80211, "mac80211 add interface type %d mac %pM",
conf->type, conf->mac_addr);
mutex_lock(&wl->mutex);
if (wl->vif) {
ret = -EBUSY;
goto out;
}
wl->vif = conf->vif;
switch (conf->type) {
case NL80211_IFTYPE_STATION:
wl->bss_type = BSS_TYPE_STA_BSS;
break;
case NL80211_IFTYPE_ADHOC:
wl->bss_type = BSS_TYPE_IBSS;
break;
default:
ret = -EOPNOTSUPP;
goto out;
}
/* FIXME: what if conf->mac_addr changes? */
out:
mutex_unlock(&wl->mutex);
return ret;
}
static void wl1271_op_remove_interface(struct ieee80211_hw *hw,
struct ieee80211_if_init_conf *conf)
{
struct wl1271 *wl = hw->priv;
mutex_lock(&wl->mutex);
wl1271_debug(DEBUG_MAC80211, "mac80211 remove interface");
wl->vif = NULL;
mutex_unlock(&wl->mutex);
}
#if 0
static int wl1271_op_config_interface(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_if_conf *conf)
{
struct wl1271 *wl = hw->priv;
struct sk_buff *beacon;
int ret;
wl1271_debug(DEBUG_MAC80211, "mac80211 config_interface bssid %pM",
conf->bssid);
wl1271_dump_ascii(DEBUG_MAC80211, "ssid: ", conf->ssid,
conf->ssid_len);
mutex_lock(&wl->mutex);
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out;
if (memcmp(wl->bssid, conf->bssid, ETH_ALEN)) {
wl1271_debug(DEBUG_MAC80211, "bssid changed");
memcpy(wl->bssid, conf->bssid, ETH_ALEN);
ret = wl1271_cmd_join(wl);
if (ret < 0)
goto out_sleep;
ret = wl1271_cmd_build_null_data(wl);
if (ret < 0)
goto out_sleep;
}
wl->ssid_len = conf->ssid_len;
if (wl->ssid_len)
memcpy(wl->ssid, conf->ssid, wl->ssid_len);
if (conf->changed & IEEE80211_IFCC_BEACON) {
beacon = ieee80211_beacon_get(hw, vif);
ret = wl1271_cmd_template_set(wl, CMD_TEMPL_BEACON,
beacon->data, beacon->len);
if (ret < 0) {
dev_kfree_skb(beacon);
goto out_sleep;
}
ret = wl1271_cmd_template_set(wl, CMD_TEMPL_PROBE_RESPONSE,
beacon->data, beacon->len);
dev_kfree_skb(beacon);
if (ret < 0)
goto out_sleep;
}
out_sleep:
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
return ret;
}
#endif
static int wl1271_join_channel(struct wl1271 *wl, int channel)
{
int ret;
/* we need to use a dummy BSSID for now */
static const u8 dummy_bssid[ETH_ALEN] = { 0x0b, 0xad, 0xde,
0xad, 0xbe, 0xef };
/* disable mac filter, so we hear everything */
wl->rx_config &= ~CFG_BSSID_FILTER_EN;
wl->channel = channel;
memcpy(wl->bssid, dummy_bssid, ETH_ALEN);
ret = wl1271_cmd_join(wl);
if (ret < 0)
goto out;
wl->joined = true;
out:
return ret;
}
static int wl1271_unjoin_channel(struct wl1271 *wl)
{
int ret;
/* to stop listening to a channel, we disconnect */
ret = wl1271_cmd_disconnect(wl);
if (ret < 0)
goto out;
wl->joined = false;
wl->channel = 0;
memset(wl->bssid, 0, ETH_ALEN);
wl->rx_config = WL1271_DEFAULT_RX_CONFIG;
out:
return ret;
}
static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed)
{
struct wl1271 *wl = hw->priv;
struct ieee80211_conf *conf = &hw->conf;
int channel, ret = 0;
channel = ieee80211_frequency_to_channel(conf->channel->center_freq);
wl1271_debug(DEBUG_MAC80211, "mac80211 config ch %d psm %s power %d %s",
channel,
conf->flags & IEEE80211_CONF_PS ? "on" : "off",
conf->power_level,
conf->flags & IEEE80211_CONF_IDLE ? "idle" : "in use");
mutex_lock(&wl->mutex);
wl->band = conf->channel->band;
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out;
if (changed & IEEE80211_CONF_CHANGE_IDLE) {
if (conf->flags & IEEE80211_CONF_IDLE && wl->joined)
wl1271_unjoin_channel(wl);
else
wl1271_join_channel(wl, channel);
if (conf->flags & IEEE80211_CONF_IDLE) {
wl->basic_rate_set = CONF_TX_RATE_MASK_BASIC;
wl1271_acx_rate_policies(wl, CONF_TX_RATE_MASK_BASIC);
}
}
/* if the channel changes while joined, join again */
if (channel != wl->channel && wl->joined)
wl1271_join_channel(wl, channel);
if (conf->flags & IEEE80211_CONF_PS && !wl->psm_requested) {
wl->psm_requested = true;
/*
* We enter PSM only if we're already associated.
* If we're not, we'll enter it when joining an SSID,
* through the bss_info_changed() hook.
*/
if (wl->associated) {
wl1271_info("psm enabled");
ret = wl1271_ps_set_mode(wl, STATION_POWER_SAVE_MODE);
}
} else if (!(conf->flags & IEEE80211_CONF_PS) &&
wl->psm_requested) {
wl1271_info("psm disabled");
wl->psm_requested = false;
if (wl->psm)
ret = wl1271_ps_set_mode(wl, STATION_ACTIVE_MODE);
}
if (conf->power_level != wl->power_level) {
ret = wl1271_acx_tx_power(wl, conf->power_level);
if (ret < 0)
goto out_sleep;
wl->power_level = conf->power_level;
}
out_sleep:
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
return ret;
}
struct wl1271_filter_params {
bool enabled;
int mc_list_length;
u8 mc_list[ACX_MC_ADDRESS_GROUP_MAX][ETH_ALEN];
};
static u64 wl1271_op_prepare_multicast(struct ieee80211_hw *hw, int mc_count,
struct dev_addr_list *mc_list)
{
struct wl1271_filter_params *fp;
int i;
fp = kzalloc(sizeof(*fp), GFP_ATOMIC);
if (!fp) {
wl1271_error("Out of memory setting filters.");
return 0;
}
/* update multicast filtering parameters */
fp->enabled = true;
if (mc_count > ACX_MC_ADDRESS_GROUP_MAX) {
mc_count = 0;
fp->enabled = false;
}
fp->mc_list_length = 0;
for (i = 0; i < mc_count; i++) {
if (mc_list->da_addrlen == ETH_ALEN) {
memcpy(fp->mc_list[fp->mc_list_length],
mc_list->da_addr, ETH_ALEN);
fp->mc_list_length++;
} else
wl1271_warning("Unknown mc address length.");
mc_list = mc_list->next;
}
return (u64)(unsigned long)fp;
}
#define WL1271_SUPPORTED_FILTERS (FIF_PROMISC_IN_BSS | \
FIF_ALLMULTI | \
FIF_FCSFAIL | \
FIF_BCN_PRBRESP_PROMISC | \
FIF_CONTROL | \
FIF_OTHER_BSS)
static void wl1271_op_configure_filter(struct ieee80211_hw *hw,
unsigned int changed,
unsigned int *total, u64 multicast)
{
struct wl1271_filter_params *fp = (void *)(unsigned long)multicast;
struct wl1271 *wl = hw->priv;
int ret;
wl1271_debug(DEBUG_MAC80211, "mac80211 configure filter");
mutex_lock(&wl->mutex);
if (wl->state == WL1271_STATE_OFF)
goto out;
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out;
*total &= WL1271_SUPPORTED_FILTERS;
changed &= WL1271_SUPPORTED_FILTERS;
if (*total & FIF_ALLMULTI)
ret = wl1271_acx_group_address_tbl(wl, false, NULL, 0);
else if (fp)
ret = wl1271_acx_group_address_tbl(wl, fp->enabled,
fp->mc_list,
fp->mc_list_length);
if (ret < 0)
goto out_sleep;
kfree(fp);
/* FIXME: We still need to set our filters properly */
/* determine, whether supported filter values have changed */
if (changed == 0)
goto out_sleep;
/* apply configured filters */
ret = wl1271_acx_rx_config(wl, wl->rx_config, wl->rx_filter);
if (ret < 0)
goto out_sleep;
out_sleep:
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
}
static int wl1271_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
struct ieee80211_vif *vif,
struct ieee80211_sta *sta,
struct ieee80211_key_conf *key_conf)
{
struct wl1271 *wl = hw->priv;
const u8 *addr;
int ret;
u32 tx_seq_32 = 0;
u16 tx_seq_16 = 0;
u8 key_type;
static const u8 bcast_addr[ETH_ALEN] =
{ 0xff, 0xff, 0xff, 0xff, 0xff, 0xff };
wl1271_debug(DEBUG_MAC80211, "mac80211 set key");
addr = sta ? sta->addr : bcast_addr;
wl1271_debug(DEBUG_CRYPT, "CMD: 0x%x", cmd);
wl1271_dump(DEBUG_CRYPT, "ADDR: ", addr, ETH_ALEN);
wl1271_debug(DEBUG_CRYPT, "Key: algo:0x%x, id:%d, len:%d flags 0x%x",
key_conf->alg, key_conf->keyidx,
key_conf->keylen, key_conf->flags);
wl1271_dump(DEBUG_CRYPT, "KEY: ", key_conf->key, key_conf->keylen);
if (is_zero_ether_addr(addr)) {
/* We dont support TX only encryption */
ret = -EOPNOTSUPP;
goto out;
}
mutex_lock(&wl->mutex);
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out_unlock;
switch (key_conf->alg) {
case ALG_WEP:
key_type = KEY_WEP;
key_conf->hw_key_idx = key_conf->keyidx;
break;
case ALG_TKIP:
key_type = KEY_TKIP;
key_conf->hw_key_idx = key_conf->keyidx;
tx_seq_32 = wl->tx_security_seq_32;
tx_seq_16 = wl->tx_security_seq_16;
break;
case ALG_CCMP:
key_type = KEY_AES;
key_conf->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
tx_seq_32 = wl->tx_security_seq_32;
tx_seq_16 = wl->tx_security_seq_16;
break;
default:
wl1271_error("Unknown key algo 0x%x", key_conf->alg);
ret = -EOPNOTSUPP;
goto out_sleep;
}
switch (cmd) {
case SET_KEY:
ret = wl1271_cmd_set_key(wl, KEY_ADD_OR_REPLACE,
key_conf->keyidx, key_type,
key_conf->keylen, key_conf->key,
addr, tx_seq_32, tx_seq_16);
if (ret < 0) {
wl1271_error("Could not add or replace key");
goto out_sleep;
}
break;
case DISABLE_KEY:
ret = wl1271_cmd_set_key(wl, KEY_REMOVE,
key_conf->keyidx, key_type,
key_conf->keylen, key_conf->key,
addr, 0, 0);
if (ret < 0) {
wl1271_error("Could not remove key");
goto out_sleep;
}
break;
default:
wl1271_error("Unsupported key cmd 0x%x", cmd);
ret = -EOPNOTSUPP;
goto out_sleep;
break;
}
out_sleep:
wl1271_ps_elp_sleep(wl);
out_unlock:
mutex_unlock(&wl->mutex);
out:
return ret;
}
static int wl1271_op_hw_scan(struct ieee80211_hw *hw,
struct cfg80211_scan_request *req)
{
struct wl1271 *wl = hw->priv;
int ret;
u8 *ssid = NULL;
size_t len = 0;
wl1271_debug(DEBUG_MAC80211, "mac80211 hw scan");
if (req->n_ssids) {
ssid = req->ssids[0].ssid;
len = req->ssids[0].ssid_len;
}
mutex_lock(&wl->mutex);
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out;
if (wl1271_11a_enabled())
ret = wl1271_cmd_scan(hw->priv, ssid, len, 1, 0,
WL1271_SCAN_BAND_DUAL, 3);
else
ret = wl1271_cmd_scan(hw->priv, ssid, len, 1, 0,
WL1271_SCAN_BAND_2_4_GHZ, 3);
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
return ret;
}
static int wl1271_op_set_rts_threshold(struct ieee80211_hw *hw, u32 value)
{
struct wl1271 *wl = hw->priv;
int ret;
mutex_lock(&wl->mutex);
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out;
ret = wl1271_acx_rts_threshold(wl, (u16) value);
if (ret < 0)
wl1271_warning("wl1271_op_set_rts_threshold failed: %d", ret);
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
return ret;
}
static u32 wl1271_enabled_rates_get(struct wl1271 *wl, u64 basic_rate_set)
{
struct ieee80211_supported_band *band;
u32 enabled_rates = 0;
int bit;
band = wl->hw->wiphy->bands[wl->band];
for (bit = 0; bit < band->n_bitrates; bit++) {
if (basic_rate_set & 0x1)
enabled_rates |= band->bitrates[bit].hw_value;
basic_rate_set >>= 1;
}
return enabled_rates;
}
static void wl1271_op_bss_info_changed(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
struct ieee80211_bss_conf *bss_conf,
u32 changed)
{
enum wl1271_cmd_ps_mode mode;
struct wl1271 *wl = hw->priv;
int ret;
wl1271_debug(DEBUG_MAC80211, "mac80211 bss info changed");
mutex_lock(&wl->mutex);
ret = wl1271_ps_elp_wakeup(wl, false);
if (ret < 0)
goto out;
if ((changed & BSS_CHANGED_BSSID) &&
/*
* Now we know the correct bssid, so we send a new join command
* and enable the BSSID filter
*/
memcmp(wl->bssid, bss_conf->bssid, ETH_ALEN)) {
wl->rx_config |= CFG_BSSID_FILTER_EN;
memcpy(wl->bssid, bss_conf->bssid, ETH_ALEN);
ret = wl1271_cmd_build_null_data(wl);
if (ret < 0) {
wl1271_warning("cmd buld null data failed %d",
ret);
goto out_sleep;
}
ret = wl1271_cmd_join(wl);
if (ret < 0) {
wl1271_warning("cmd join failed %d", ret);
goto out_sleep;
}
wl->joined = true;
}
if (changed & BSS_CHANGED_ASSOC) {
if (bss_conf->assoc) {
wl->aid = bss_conf->aid;
wl->associated = true;
/*
* with wl1271, we don't need to update the
* beacon_int and dtim_period, because the firmware
* updates it by itself when the first beacon is
* received after a join.
*/
ret = wl1271_cmd_build_ps_poll(wl, wl->aid);
if (ret < 0)
goto out_sleep;
ret = wl1271_acx_aid(wl, wl->aid);
if (ret < 0)
goto out_sleep;
/* If we want to go in PSM but we're not there yet */
if (wl->psm_requested && !wl->psm) {
mode = STATION_POWER_SAVE_MODE;
ret = wl1271_ps_set_mode(wl, mode);
if (ret < 0)
goto out_sleep;
}
} else {
/* use defaults when not associated */
wl->associated = false;
wl->aid = 0;
}
}
if (changed & BSS_CHANGED_ERP_SLOT) {
if (bss_conf->use_short_slot)
ret = wl1271_acx_slot(wl, SLOT_TIME_SHORT);
else
ret = wl1271_acx_slot(wl, SLOT_TIME_LONG);
if (ret < 0) {
wl1271_warning("Set slot time failed %d", ret);
goto out_sleep;
}
}
if (changed & BSS_CHANGED_ERP_PREAMBLE) {
if (bss_conf->use_short_preamble)
wl1271_acx_set_preamble(wl, ACX_PREAMBLE_SHORT);
else
wl1271_acx_set_preamble(wl, ACX_PREAMBLE_LONG);
}
if (changed & BSS_CHANGED_ERP_CTS_PROT) {
if (bss_conf->use_cts_prot)
ret = wl1271_acx_cts_protect(wl, CTSPROTECT_ENABLE);
else
ret = wl1271_acx_cts_protect(wl, CTSPROTECT_DISABLE);
if (ret < 0) {
wl1271_warning("Set ctsprotect failed %d", ret);
goto out_sleep;
}
}
if (changed & BSS_CHANGED_BASIC_RATES) {
wl->basic_rate_set = wl1271_enabled_rates_get(
wl, bss_conf->basic_rates);
ret = wl1271_acx_rate_policies(wl, wl->basic_rate_set);
if (ret < 0) {
wl1271_warning("Set rate policies failed %d", ret);
goto out_sleep;
}
}
out_sleep:
wl1271_ps_elp_sleep(wl);
out:
mutex_unlock(&wl->mutex);
}
/* can't be const, mac80211 writes to this */
static struct ieee80211_rate wl1271_rates[] = {
{ .bitrate = 10,
.hw_value = CONF_HW_BIT_RATE_1MBPS,
.hw_value_short = CONF_HW_BIT_RATE_1MBPS, },
{ .bitrate = 20,
.hw_value = CONF_HW_BIT_RATE_2MBPS,
.hw_value_short = CONF_HW_BIT_RATE_2MBPS,
.flags = IEEE80211_RATE_SHORT_PREAMBLE },
{ .bitrate = 55,
.hw_value = CONF_HW_BIT_RATE_5_5MBPS,
.hw_value_short = CONF_HW_BIT_RATE_5_5MBPS,
.flags = IEEE80211_RATE_SHORT_PREAMBLE },
{ .bitrate = 110,
.hw_value = CONF_HW_BIT_RATE_11MBPS,
.hw_value_short = CONF_HW_BIT_RATE_11MBPS,
.flags = IEEE80211_RATE_SHORT_PREAMBLE },
{ .bitrate = 60,
.hw_value = CONF_HW_BIT_RATE_6MBPS,
.hw_value_short = CONF_HW_BIT_RATE_6MBPS, },
{ .bitrate = 90,
.hw_value = CONF_HW_BIT_RATE_9MBPS,
.hw_value_short = CONF_HW_BIT_RATE_9MBPS, },
{ .bitrate = 120,
.hw_value = CONF_HW_BIT_RATE_12MBPS,
.hw_value_short = CONF_HW_BIT_RATE_12MBPS, },
{ .bitrate = 180,
.hw_value = CONF_HW_BIT_RATE_18MBPS,
.hw_value_short = CONF_HW_BIT_RATE_18MBPS, },
{ .bitrate = 240,
.hw_value = CONF_HW_BIT_RATE_24MBPS,
.hw_value_short = CONF_HW_BIT_RATE_24MBPS, },
{ .bitrate = 360,
.hw_value = CONF_HW_BIT_RATE_36MBPS,
.hw_value_short = CONF_HW_BIT_RATE_36MBPS, },
{ .bitrate = 480,
.hw_value = CONF_HW_BIT_RATE_48MBPS,
.hw_value_short = CONF_HW_BIT_RATE_48MBPS, },
{ .bitrate = 540,
.hw_value = CONF_HW_BIT_RATE_54MBPS,
.hw_value_short = CONF_HW_BIT_RATE_54MBPS, },
};
/* can't be const, mac80211 writes to this */
static struct ieee80211_channel wl1271_channels[] = {
{ .hw_value = 1, .center_freq = 2412, .max_power = 25 },
{ .hw_value = 2, .center_freq = 2417, .max_power = 25 },
{ .hw_value = 3, .center_freq = 2422, .max_power = 25 },
{ .hw_value = 4, .center_freq = 2427, .max_power = 25 },
{ .hw_value = 5, .center_freq = 2432, .max_power = 25 },
{ .hw_value = 6, .center_freq = 2437, .max_power = 25 },
{ .hw_value = 7, .center_freq = 2442, .max_power = 25 },
{ .hw_value = 8, .center_freq = 2447, .max_power = 25 },
{ .hw_value = 9, .center_freq = 2452, .max_power = 25 },
{ .hw_value = 10, .center_freq = 2457, .max_power = 25 },
{ .hw_value = 11, .center_freq = 2462, .max_power = 25 },
{ .hw_value = 12, .center_freq = 2467, .max_power = 25 },
{ .hw_value = 13, .center_freq = 2472, .max_power = 25 },
};
/* can't be const, mac80211 writes to this */
static struct ieee80211_supported_band wl1271_band_2ghz = {
.channels = wl1271_channels,
.n_channels = ARRAY_SIZE(wl1271_channels),
.bitrates = wl1271_rates,
.n_bitrates = ARRAY_SIZE(wl1271_rates),
};
/* 5 GHz data rates for WL1273 */
static struct ieee80211_rate wl1271_rates_5ghz[] = {
{ .bitrate = 60,
.hw_value = CONF_HW_BIT_RATE_6MBPS,
.hw_value_short = CONF_HW_BIT_RATE_6MBPS, },
{ .bitrate = 90,
.hw_value = CONF_HW_BIT_RATE_9MBPS,
.hw_value_short = CONF_HW_BIT_RATE_9MBPS, },
{ .bitrate = 120,
.hw_value = CONF_HW_BIT_RATE_12MBPS,
.hw_value_short = CONF_HW_BIT_RATE_12MBPS, },
{ .bitrate = 180,
.hw_value = CONF_HW_BIT_RATE_18MBPS,
.hw_value_short = CONF_HW_BIT_RATE_18MBPS, },
{ .bitrate = 240,
.hw_value = CONF_HW_BIT_RATE_24MBPS,
.hw_value_short = CONF_HW_BIT_RATE_24MBPS, },
{ .bitrate = 360,
.hw_value = CONF_HW_BIT_RATE_36MBPS,
.hw_value_short = CONF_HW_BIT_RATE_36MBPS, },
{ .bitrate = 480,
.hw_value = CONF_HW_BIT_RATE_48MBPS,
.hw_value_short = CONF_HW_BIT_RATE_48MBPS, },
{ .bitrate = 540,
.hw_value = CONF_HW_BIT_RATE_54MBPS,
.hw_value_short = CONF_HW_BIT_RATE_54MBPS, },
};
/* 5 GHz band channels for WL1273 */
static struct ieee80211_channel wl1271_channels_5ghz[] = {
{ .hw_value = 183, .center_freq = 4915},
{ .hw_value = 184, .center_freq = 4920},
{ .hw_value = 185, .center_freq = 4925},
{ .hw_value = 187, .center_freq = 4935},
{ .hw_value = 188, .center_freq = 4940},
{ .hw_value = 189, .center_freq = 4945},
{ .hw_value = 192, .center_freq = 4960},
{ .hw_value = 196, .center_freq = 4980},
{ .hw_value = 7, .center_freq = 5035},
{ .hw_value = 8, .center_freq = 5040},
{ .hw_value = 9, .center_freq = 5045},
{ .hw_value = 11, .center_freq = 5055},
{ .hw_value = 12, .center_freq = 5060},
{ .hw_value = 16, .center_freq = 5080},
{ .hw_value = 34, .center_freq = 5170},
{ .hw_value = 36, .center_freq = 5180},
{ .hw_value = 38, .center_freq = 5190},
{ .hw_value = 40, .center_freq = 5200},
{ .hw_value = 42, .center_freq = 5210},
{ .hw_value = 44, .center_freq = 5220},
{ .hw_value = 46, .center_freq = 5230},
{ .hw_value = 48, .center_freq = 5240},
{ .hw_value = 52, .center_freq = 5260},
{ .hw_value = 56, .center_freq = 5280},
{ .hw_value = 60, .center_freq = 5300},
{ .hw_value = 64, .center_freq = 5320},
{ .hw_value = 100, .center_freq = 5500},
{ .hw_value = 104, .center_freq = 5520},
{ .hw_value = 108, .center_freq = 5540},
{ .hw_value = 112, .center_freq = 5560},
{ .hw_value = 116, .center_freq = 5580},
{ .hw_value = 120, .center_freq = 5600},
{ .hw_value = 124, .center_freq = 5620},
{ .hw_value = 128, .center_freq = 5640},
{ .hw_value = 132, .center_freq = 5660},
{ .hw_value = 136, .center_freq = 5680},
{ .hw_value = 140, .center_freq = 5700},
{ .hw_value = 149, .center_freq = 5745},
{ .hw_value = 153, .center_freq = 5765},
{ .hw_value = 157, .center_freq = 5785},
{ .hw_value = 161, .center_freq = 5805},
{ .hw_value = 165, .center_freq = 5825},
};
static struct ieee80211_supported_band wl1271_band_5ghz = {
.channels = wl1271_channels_5ghz,
.n_channels = ARRAY_SIZE(wl1271_channels_5ghz),
.bitrates = wl1271_rates_5ghz,
.n_bitrates = ARRAY_SIZE(wl1271_rates_5ghz),
};
static const struct ieee80211_ops wl1271_ops = {
.start = wl1271_op_start,
.stop = wl1271_op_stop,
.add_interface = wl1271_op_add_interface,
.remove_interface = wl1271_op_remove_interface,
.config = wl1271_op_config,
/* .config_interface = wl1271_op_config_interface, */
.prepare_multicast = wl1271_op_prepare_multicast,
.configure_filter = wl1271_op_configure_filter,
.tx = wl1271_op_tx,
.set_key = wl1271_op_set_key,
.hw_scan = wl1271_op_hw_scan,
.bss_info_changed = wl1271_op_bss_info_changed,
.set_rts_threshold = wl1271_op_set_rts_threshold,
};
static int wl1271_register_hw(struct wl1271 *wl)
{
int ret;
if (wl->mac80211_registered)
return 0;
SET_IEEE80211_PERM_ADDR(wl->hw, wl->mac_addr);
ret = ieee80211_register_hw(wl->hw);
if (ret < 0) {
wl1271_error("unable to register mac80211 hw: %d", ret);
return ret;
}
wl->mac80211_registered = true;
wl1271_notice("loaded");
return 0;
}
static int wl1271_init_ieee80211(struct wl1271 *wl)
{
/* The tx descriptor buffer and the TKIP space. */
wl->hw->extra_tx_headroom = WL1271_TKIP_IV_SPACE +
sizeof(struct wl1271_tx_hw_descr);
/* unit us */
/* FIXME: find a proper value */
wl->hw->channel_change_time = 10000;
wl->hw->flags = IEEE80211_HW_SIGNAL_DBM |
IEEE80211_HW_NOISE_DBM |
IEEE80211_HW_BEACON_FILTER |
IEEE80211_HW_SUPPORTS_PS;
wl->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
wl->hw->wiphy->max_scan_ssids = 1;
wl->hw->wiphy->bands[IEEE80211_BAND_2GHZ] = &wl1271_band_2ghz;
if (wl1271_11a_enabled())
wl->hw->wiphy->bands[IEEE80211_BAND_5GHZ] = &wl1271_band_5ghz;
SET_IEEE80211_DEV(wl->hw, &wl->spi->dev);
return 0;
}
static void wl1271_device_release(struct device *dev)
{
}
static struct platform_device wl1271_device = {
.name = "wl1271",
.id = -1,
/* device model insists to have a release function */
.dev = {
.release = wl1271_device_release,
},
};
#define WL1271_DEFAULT_CHANNEL 0
static int __devinit wl1271_probe(struct spi_device *spi)
{
struct wl12xx_platform_data *pdata;
struct ieee80211_hw *hw;
struct wl1271 *wl;
int ret, i;
static const u8 nokia_oui[3] = {0x00, 0x1f, 0xdf};
pdata = spi->dev.platform_data;
if (!pdata) {
wl1271_error("no platform data");
return -ENODEV;
}
hw = ieee80211_alloc_hw(sizeof(*wl), &wl1271_ops);
if (!hw) {
wl1271_error("could not alloc ieee80211_hw");
return -ENOMEM;
}
wl = hw->priv;
memset(wl, 0, sizeof(*wl));
INIT_LIST_HEAD(&wl->list);
wl->hw = hw;
dev_set_drvdata(&spi->dev, wl);
wl->spi = spi;
skb_queue_head_init(&wl->tx_queue);
INIT_DELAYED_WORK(&wl->elp_work, wl1271_elp_work);
wl->channel = WL1271_DEFAULT_CHANNEL;
wl->scanning = false;
wl->default_key = 0;
wl->rx_counter = 0;
wl->rx_config = WL1271_DEFAULT_RX_CONFIG;
wl->rx_filter = WL1271_DEFAULT_RX_FILTER;
wl->elp = false;
wl->psm = 0;
wl->psm_requested = false;
wl->psm_entry_retry = 0;
wl->associated = false;
wl->tx_queue_stopped = false;
wl->power_level = WL1271_DEFAULT_POWER_LEVEL;
wl->basic_rate_set = CONF_TX_RATE_MASK_BASIC;
wl->band = IEEE80211_BAND_2GHZ;
wl->vif = NULL;
wl->joined = false;
wl->gpio_power = false;
for (i = 0; i < ACX_TX_DESCRIPTORS; i++)
wl->tx_frames[i] = NULL;
spin_lock_init(&wl->wl_lock);
/*
* In case our MAC address is not correctly set,
* we use a random but Nokia MAC.
*/
memcpy(wl->mac_addr, nokia_oui, 3);
get_random_bytes(wl->mac_addr + 3, 3);
wl->state = WL1271_STATE_OFF;
mutex_init(&wl->mutex);
/* This is the only SPI value that we need to set here, the rest
* comes from the board-peripherals file */
spi->bits_per_word = 32;
ret = spi_setup(spi);
if (ret < 0) {
wl1271_error("spi_setup failed");
goto out_free;
}
wl->set_power = pdata->set_power;
if (!wl->set_power) {
wl1271_error("set power function missing in platform data");
ret = -ENODEV;
goto out_free;
}
wl->irq = spi->irq;
if (wl->irq < 0) {
wl1271_error("irq missing in platform data");
ret = -ENODEV;
goto out_free;
}
ret = request_irq(wl->irq, wl1271_irq, 0, DRIVER_NAME, wl);
if (ret < 0) {
wl1271_error("request_irq() failed: %d", ret);
goto out_free;
}
set_irq_type(wl->irq, IRQ_TYPE_EDGE_RISING);
disable_irq(wl->irq);
ret = platform_device_register(&wl1271_device);
if (ret) {
wl1271_error("couldn't register platform device");
goto out_irq;
}
dev_set_drvdata(&wl1271_device.dev, wl);
/* Apply default driver configuration. */
wl1271_conf_init(wl);
ret = wl1271_init_ieee80211(wl);
if (ret)
goto out_platform;
ret = wl1271_register_hw(wl);
if (ret)
goto out_platform;
wl1271_debugfs_init(wl);
wl1271_notice("initialized");
return 0;
out_platform:
platform_device_unregister(&wl1271_device);
out_irq:
free_irq(wl->irq, wl);
out_free:
ieee80211_free_hw(hw);
return ret;
}
static int __devexit wl1271_remove(struct spi_device *spi)
{
struct wl1271 *wl = dev_get_drvdata(&spi->dev);
ieee80211_unregister_hw(wl->hw);
wl1271_debugfs_exit(wl);
platform_device_unregister(&wl1271_device);
free_irq(wl->irq, wl);
kfree(wl->target_mem_map);
vfree(wl->fw);
wl->fw = NULL;
kfree(wl->nvs);
wl->nvs = NULL;
kfree(wl->fw_status);
kfree(wl->tx_res_if);
ieee80211_free_hw(wl->hw);
return 0;
}
static struct spi_driver wl1271_spi_driver = {
.driver = {
.name = "wl1271",
.bus = &spi_bus_type,
.owner = THIS_MODULE,
},
.probe = wl1271_probe,
.remove = __devexit_p(wl1271_remove),
};
static int __init wl1271_init(void)
{
int ret;
ret = spi_register_driver(&wl1271_spi_driver);
if (ret < 0) {
wl1271_error("failed to register spi driver: %d", ret);
goto out;
}
out:
return ret;
}
static void __exit wl1271_exit(void)
{
spi_unregister_driver(&wl1271_spi_driver);
wl1271_notice("unloaded");
}
module_init(wl1271_init);
module_exit(wl1271_exit);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Luciano Coelho <luciano.coelho@nokia.com>");
MODULE_AUTHOR("Juuso Oikarinen <juuso.oikarinen@nokia.com>");
MODULE_FIRMWARE(WL1271_FW_NAME);