License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 21:07:57 +07:00
|
|
|
/* SPDX-License-Identifier: GPL-2.0 */
|
2007-08-28 03:49:44 +07:00
|
|
|
#ifndef __EXTENTMAP__
|
|
|
|
#define __EXTENTMAP__
|
|
|
|
|
|
|
|
#include <linux/rbtree.h>
|
2017-03-03 15:55:12 +07:00
|
|
|
#include <linux/refcount.h>
|
2007-08-28 03:49:44 +07:00
|
|
|
|
2013-10-31 12:01:13 +07:00
|
|
|
#define EXTENT_MAP_LAST_BYTE ((u64)-4)
|
|
|
|
#define EXTENT_MAP_HOLE ((u64)-3)
|
|
|
|
#define EXTENT_MAP_INLINE ((u64)-2)
|
|
|
|
#define EXTENT_MAP_DELALLOC ((u64)-1)
|
2007-08-28 03:49:44 +07:00
|
|
|
|
2008-07-18 23:01:11 +07:00
|
|
|
/* bits for the flags field */
|
|
|
|
#define EXTENT_FLAG_PINNED 0 /* this entry not yet on disk, don't free it */
|
Btrfs: Add zlib compression support
This is a large change for adding compression on reading and writing,
both for inline and regular extents. It does some fairly large
surgery to the writeback paths.
Compression is off by default and enabled by mount -o compress. Even
when the -o compress mount option is not used, it is possible to read
compressed extents off the disk.
If compression for a given set of pages fails to make them smaller, the
file is flagged to avoid future compression attempts later.
* While finding delalloc extents, the pages are locked before being sent down
to the delalloc handler. This allows the delalloc handler to do complex things
such as cleaning the pages, marking them writeback and starting IO on their
behalf.
* Inline extents are inserted at delalloc time now. This allows us to compress
the data before inserting the inline extent, and it allows us to insert
an inline extent that spans multiple pages.
* All of the in-memory extent representations (extent_map.c, ordered-data.c etc)
are changed to record both an in-memory size and an on disk size, as well
as a flag for compression.
From a disk format point of view, the extent pointers in the file are changed
to record the on disk size of a given extent and some encoding flags.
Space in the disk format is allocated for compression encoding, as well
as encryption and a generic 'other' field. Neither the encryption or the
'other' field are currently used.
In order to limit the amount of data read for a single random read in the
file, the size of a compressed extent is limited to 128k. This is a
software only limit, the disk format supports u64 sized compressed extents.
In order to limit the ram consumed while processing extents, the uncompressed
size of a compressed extent is limited to 256k. This is a software only limit
and will be subject to tuning later.
Checksumming is still done on compressed extents, and it is done on the
uncompressed version of the data. This way additional encodings can be
layered on without having to figure out which encoding to checksum.
Compression happens at delalloc time, which is basically singled threaded because
it is usually done by a single pdflush thread. This makes it tricky to
spread the compression load across all the cpus on the box. We'll have to
look at parallel pdflush walks of dirty inodes at a later time.
Decompression is hooked into readpages and it does spread across CPUs nicely.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
2008-10-30 01:49:59 +07:00
|
|
|
#define EXTENT_FLAG_COMPRESSED 1
|
2008-10-31 01:25:28 +07:00
|
|
|
#define EXTENT_FLAG_PREALLOC 3 /* pre-allocated extent */
|
2012-09-14 23:59:20 +07:00
|
|
|
#define EXTENT_FLAG_LOGGING 4 /* Logging this extent */
|
2012-12-03 22:58:15 +07:00
|
|
|
#define EXTENT_FLAG_FILLING 5 /* Filling in a preallocated extent */
|
2014-06-19 09:42:52 +07:00
|
|
|
#define EXTENT_FLAG_FS_MAPPING 6 /* filesystem extent mapping type */
|
2008-07-18 23:01:11 +07:00
|
|
|
|
2007-08-28 03:49:44 +07:00
|
|
|
struct extent_map {
|
|
|
|
struct rb_node rb_node;
|
2008-01-25 04:13:08 +07:00
|
|
|
|
|
|
|
/* all of these are in bytes */
|
|
|
|
u64 start;
|
|
|
|
u64 len;
|
2012-08-27 23:52:20 +07:00
|
|
|
u64 mod_start;
|
|
|
|
u64 mod_len;
|
2008-11-10 19:34:43 +07:00
|
|
|
u64 orig_start;
|
2012-12-03 22:31:19 +07:00
|
|
|
u64 orig_block_len;
|
2013-04-05 01:31:27 +07:00
|
|
|
u64 ram_bytes;
|
2007-08-28 03:49:44 +07:00
|
|
|
u64 block_start;
|
Btrfs: Add zlib compression support
This is a large change for adding compression on reading and writing,
both for inline and regular extents. It does some fairly large
surgery to the writeback paths.
Compression is off by default and enabled by mount -o compress. Even
when the -o compress mount option is not used, it is possible to read
compressed extents off the disk.
If compression for a given set of pages fails to make them smaller, the
file is flagged to avoid future compression attempts later.
* While finding delalloc extents, the pages are locked before being sent down
to the delalloc handler. This allows the delalloc handler to do complex things
such as cleaning the pages, marking them writeback and starting IO on their
behalf.
* Inline extents are inserted at delalloc time now. This allows us to compress
the data before inserting the inline extent, and it allows us to insert
an inline extent that spans multiple pages.
* All of the in-memory extent representations (extent_map.c, ordered-data.c etc)
are changed to record both an in-memory size and an on disk size, as well
as a flag for compression.
From a disk format point of view, the extent pointers in the file are changed
to record the on disk size of a given extent and some encoding flags.
Space in the disk format is allocated for compression encoding, as well
as encryption and a generic 'other' field. Neither the encryption or the
'other' field are currently used.
In order to limit the amount of data read for a single random read in the
file, the size of a compressed extent is limited to 128k. This is a
software only limit, the disk format supports u64 sized compressed extents.
In order to limit the ram consumed while processing extents, the uncompressed
size of a compressed extent is limited to 256k. This is a software only limit
and will be subject to tuning later.
Checksumming is still done on compressed extents, and it is done on the
uncompressed version of the data. This way additional encodings can be
layered on without having to figure out which encoding to checksum.
Compression happens at delalloc time, which is basically singled threaded because
it is usually done by a single pdflush thread. This makes it tricky to
spread the compression load across all the cpus on the box. We'll have to
look at parallel pdflush walks of dirty inodes at a later time.
Decompression is hooked into readpages and it does spread across CPUs nicely.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
2008-10-30 01:49:59 +07:00
|
|
|
u64 block_len;
|
Btrfs: turbo charge fsync
At least for the vm workload. Currently on fsync we will
1) Truncate all items in the log tree for the given inode if they exist
and
2) Copy all items for a given inode into the log
The problem with this is that for things like VMs you can have lots of
extents from the fragmented writing behavior, and worst yet you may have
only modified a few extents, not the entire thing. This patch fixes this
problem by tracking which transid modified our extent, and then when we do
the tree logging we find all of the extents we've modified in our current
transaction, sort them and commit them. We also only truncate up to the
xattrs of the inode and copy that stuff in normally, and then just drop any
extents in the range we have that exist in the log already. Here are some
numbers of a 50 meg fio job that does random writes and fsync()s after every
write
Original Patched
SATA drive 82KB/s 140KB/s
Fusion drive 431KB/s 2532KB/s
So around 2-6 times faster depending on your hardware. There are a few
corner cases, for example if you truncate at all we have to do it the old
way since there is no way to be sure what is in the log is ok. This
probably could be done smarter, but if you write-fsync-truncate-write-fsync
you deserve what you get. All this work is in RAM of course so if your
inode gets evicted from cache and you read it in and fsync it we'll do it
the slow way if we are still in the same transaction that we last modified
the inode in.
The biggest cool part of this is that it requires no changes to the recovery
code, so if you fsync with this patch and crash and load an old kernel, it
will run the recovery and be a-ok. I have tested this pretty thoroughly
with an fsync tester and everything comes back fine, as well as xfstests.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
2012-08-18 00:14:17 +07:00
|
|
|
u64 generation;
|
2008-01-25 04:13:08 +07:00
|
|
|
unsigned long flags;
|
2015-06-03 21:55:48 +07:00
|
|
|
union {
|
|
|
|
struct block_device *bdev;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* used for chunk mappings
|
|
|
|
* flags & EXTENT_FLAG_FS_MAPPING must be set
|
|
|
|
*/
|
|
|
|
struct map_lookup *map_lookup;
|
|
|
|
};
|
2017-03-03 15:55:12 +07:00
|
|
|
refcount_t refs;
|
2012-01-27 03:01:12 +07:00
|
|
|
unsigned int compress_type;
|
Btrfs: turbo charge fsync
At least for the vm workload. Currently on fsync we will
1) Truncate all items in the log tree for the given inode if they exist
and
2) Copy all items for a given inode into the log
The problem with this is that for things like VMs you can have lots of
extents from the fragmented writing behavior, and worst yet you may have
only modified a few extents, not the entire thing. This patch fixes this
problem by tracking which transid modified our extent, and then when we do
the tree logging we find all of the extents we've modified in our current
transaction, sort them and commit them. We also only truncate up to the
xattrs of the inode and copy that stuff in normally, and then just drop any
extents in the range we have that exist in the log already. Here are some
numbers of a 50 meg fio job that does random writes and fsync()s after every
write
Original Patched
SATA drive 82KB/s 140KB/s
Fusion drive 431KB/s 2532KB/s
So around 2-6 times faster depending on your hardware. There are a few
corner cases, for example if you truncate at all we have to do it the old
way since there is no way to be sure what is in the log is ok. This
probably could be done smarter, but if you write-fsync-truncate-write-fsync
you deserve what you get. All this work is in RAM of course so if your
inode gets evicted from cache and you read it in and fsync it we'll do it
the slow way if we are still in the same transaction that we last modified
the inode in.
The biggest cool part of this is that it requires no changes to the recovery
code, so if you fsync with this patch and crash and load an old kernel, it
will run the recovery and be a-ok. I have tested this pretty thoroughly
with an fsync tester and everything comes back fine, as well as xfstests.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
2012-08-18 00:14:17 +07:00
|
|
|
struct list_head list;
|
2007-08-28 03:49:44 +07:00
|
|
|
};
|
|
|
|
|
2008-01-25 04:13:08 +07:00
|
|
|
struct extent_map_tree {
|
|
|
|
struct rb_root map;
|
Btrfs: turbo charge fsync
At least for the vm workload. Currently on fsync we will
1) Truncate all items in the log tree for the given inode if they exist
and
2) Copy all items for a given inode into the log
The problem with this is that for things like VMs you can have lots of
extents from the fragmented writing behavior, and worst yet you may have
only modified a few extents, not the entire thing. This patch fixes this
problem by tracking which transid modified our extent, and then when we do
the tree logging we find all of the extents we've modified in our current
transaction, sort them and commit them. We also only truncate up to the
xattrs of the inode and copy that stuff in normally, and then just drop any
extents in the range we have that exist in the log already. Here are some
numbers of a 50 meg fio job that does random writes and fsync()s after every
write
Original Patched
SATA drive 82KB/s 140KB/s
Fusion drive 431KB/s 2532KB/s
So around 2-6 times faster depending on your hardware. There are a few
corner cases, for example if you truncate at all we have to do it the old
way since there is no way to be sure what is in the log is ok. This
probably could be done smarter, but if you write-fsync-truncate-write-fsync
you deserve what you get. All this work is in RAM of course so if your
inode gets evicted from cache and you read it in and fsync it we'll do it
the slow way if we are still in the same transaction that we last modified
the inode in.
The biggest cool part of this is that it requires no changes to the recovery
code, so if you fsync with this patch and crash and load an old kernel, it
will run the recovery and be a-ok. I have tested this pretty thoroughly
with an fsync tester and everything comes back fine, as well as xfstests.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
2012-08-18 00:14:17 +07:00
|
|
|
struct list_head modified_extents;
|
2009-09-03 03:24:52 +07:00
|
|
|
rwlock_t lock;
|
2007-08-28 03:49:44 +07:00
|
|
|
};
|
|
|
|
|
2014-02-25 21:15:12 +07:00
|
|
|
static inline int extent_map_in_tree(const struct extent_map *em)
|
|
|
|
{
|
|
|
|
return !RB_EMPTY_NODE(&em->rb_node);
|
|
|
|
}
|
|
|
|
|
2008-01-25 04:13:08 +07:00
|
|
|
static inline u64 extent_map_end(struct extent_map *em)
|
|
|
|
{
|
|
|
|
if (em->start + em->len < em->start)
|
|
|
|
return (u64)-1;
|
|
|
|
return em->start + em->len;
|
|
|
|
}
|
|
|
|
|
|
|
|
static inline u64 extent_map_block_end(struct extent_map *em)
|
|
|
|
{
|
Btrfs: Add zlib compression support
This is a large change for adding compression on reading and writing,
both for inline and regular extents. It does some fairly large
surgery to the writeback paths.
Compression is off by default and enabled by mount -o compress. Even
when the -o compress mount option is not used, it is possible to read
compressed extents off the disk.
If compression for a given set of pages fails to make them smaller, the
file is flagged to avoid future compression attempts later.
* While finding delalloc extents, the pages are locked before being sent down
to the delalloc handler. This allows the delalloc handler to do complex things
such as cleaning the pages, marking them writeback and starting IO on their
behalf.
* Inline extents are inserted at delalloc time now. This allows us to compress
the data before inserting the inline extent, and it allows us to insert
an inline extent that spans multiple pages.
* All of the in-memory extent representations (extent_map.c, ordered-data.c etc)
are changed to record both an in-memory size and an on disk size, as well
as a flag for compression.
From a disk format point of view, the extent pointers in the file are changed
to record the on disk size of a given extent and some encoding flags.
Space in the disk format is allocated for compression encoding, as well
as encryption and a generic 'other' field. Neither the encryption or the
'other' field are currently used.
In order to limit the amount of data read for a single random read in the
file, the size of a compressed extent is limited to 128k. This is a
software only limit, the disk format supports u64 sized compressed extents.
In order to limit the ram consumed while processing extents, the uncompressed
size of a compressed extent is limited to 256k. This is a software only limit
and will be subject to tuning later.
Checksumming is still done on compressed extents, and it is done on the
uncompressed version of the data. This way additional encodings can be
layered on without having to figure out which encoding to checksum.
Compression happens at delalloc time, which is basically singled threaded because
it is usually done by a single pdflush thread. This makes it tricky to
spread the compression load across all the cpus on the box. We'll have to
look at parallel pdflush walks of dirty inodes at a later time.
Decompression is hooked into readpages and it does spread across CPUs nicely.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
2008-10-30 01:49:59 +07:00
|
|
|
if (em->block_start + em->block_len < em->block_start)
|
2008-01-25 04:13:08 +07:00
|
|
|
return (u64)-1;
|
Btrfs: Add zlib compression support
This is a large change for adding compression on reading and writing,
both for inline and regular extents. It does some fairly large
surgery to the writeback paths.
Compression is off by default and enabled by mount -o compress. Even
when the -o compress mount option is not used, it is possible to read
compressed extents off the disk.
If compression for a given set of pages fails to make them smaller, the
file is flagged to avoid future compression attempts later.
* While finding delalloc extents, the pages are locked before being sent down
to the delalloc handler. This allows the delalloc handler to do complex things
such as cleaning the pages, marking them writeback and starting IO on their
behalf.
* Inline extents are inserted at delalloc time now. This allows us to compress
the data before inserting the inline extent, and it allows us to insert
an inline extent that spans multiple pages.
* All of the in-memory extent representations (extent_map.c, ordered-data.c etc)
are changed to record both an in-memory size and an on disk size, as well
as a flag for compression.
From a disk format point of view, the extent pointers in the file are changed
to record the on disk size of a given extent and some encoding flags.
Space in the disk format is allocated for compression encoding, as well
as encryption and a generic 'other' field. Neither the encryption or the
'other' field are currently used.
In order to limit the amount of data read for a single random read in the
file, the size of a compressed extent is limited to 128k. This is a
software only limit, the disk format supports u64 sized compressed extents.
In order to limit the ram consumed while processing extents, the uncompressed
size of a compressed extent is limited to 256k. This is a software only limit
and will be subject to tuning later.
Checksumming is still done on compressed extents, and it is done on the
uncompressed version of the data. This way additional encodings can be
layered on without having to figure out which encoding to checksum.
Compression happens at delalloc time, which is basically singled threaded because
it is usually done by a single pdflush thread. This makes it tricky to
spread the compression load across all the cpus on the box. We'll have to
look at parallel pdflush walks of dirty inodes at a later time.
Decompression is hooked into readpages and it does spread across CPUs nicely.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
2008-10-30 01:49:59 +07:00
|
|
|
return em->block_start + em->block_len;
|
2008-01-25 04:13:08 +07:00
|
|
|
}
|
2007-08-28 03:49:44 +07:00
|
|
|
|
2011-04-21 05:34:43 +07:00
|
|
|
void extent_map_tree_init(struct extent_map_tree *tree);
|
2007-08-28 03:49:44 +07:00
|
|
|
struct extent_map *lookup_extent_mapping(struct extent_map_tree *tree,
|
2008-01-25 04:13:08 +07:00
|
|
|
u64 start, u64 len);
|
2007-08-28 03:49:44 +07:00
|
|
|
int add_extent_mapping(struct extent_map_tree *tree,
|
2013-04-06 03:51:15 +07:00
|
|
|
struct extent_map *em, int modified);
|
2007-08-28 03:49:44 +07:00
|
|
|
int remove_extent_mapping(struct extent_map_tree *tree, struct extent_map *em);
|
2014-02-25 21:15:13 +07:00
|
|
|
void replace_extent_mapping(struct extent_map_tree *tree,
|
|
|
|
struct extent_map *cur,
|
|
|
|
struct extent_map *new,
|
|
|
|
int modified);
|
2008-01-25 04:13:08 +07:00
|
|
|
|
2011-04-21 05:48:27 +07:00
|
|
|
struct extent_map *alloc_extent_map(void);
|
2007-08-28 03:49:44 +07:00
|
|
|
void free_extent_map(struct extent_map *em);
|
2007-11-19 22:22:33 +07:00
|
|
|
int __init extent_map_init(void);
|
2007-12-11 21:25:06 +07:00
|
|
|
void extent_map_exit(void);
|
Btrfs: turbo charge fsync
At least for the vm workload. Currently on fsync we will
1) Truncate all items in the log tree for the given inode if they exist
and
2) Copy all items for a given inode into the log
The problem with this is that for things like VMs you can have lots of
extents from the fragmented writing behavior, and worst yet you may have
only modified a few extents, not the entire thing. This patch fixes this
problem by tracking which transid modified our extent, and then when we do
the tree logging we find all of the extents we've modified in our current
transaction, sort them and commit them. We also only truncate up to the
xattrs of the inode and copy that stuff in normally, and then just drop any
extents in the range we have that exist in the log already. Here are some
numbers of a 50 meg fio job that does random writes and fsync()s after every
write
Original Patched
SATA drive 82KB/s 140KB/s
Fusion drive 431KB/s 2532KB/s
So around 2-6 times faster depending on your hardware. There are a few
corner cases, for example if you truncate at all we have to do it the old
way since there is no way to be sure what is in the log is ok. This
probably could be done smarter, but if you write-fsync-truncate-write-fsync
you deserve what you get. All this work is in RAM of course so if your
inode gets evicted from cache and you read it in and fsync it we'll do it
the slow way if we are still in the same transaction that we last modified
the inode in.
The biggest cool part of this is that it requires no changes to the recovery
code, so if you fsync with this patch and crash and load an old kernel, it
will run the recovery and be a-ok. I have tested this pretty thoroughly
with an fsync tester and everything comes back fine, as well as xfstests.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
2012-08-18 00:14:17 +07:00
|
|
|
int unpin_extent_cache(struct extent_map_tree *tree, u64 start, u64 len, u64 gen);
|
2013-01-25 00:02:07 +07:00
|
|
|
void clear_em_logging(struct extent_map_tree *tree, struct extent_map *em);
|
2009-09-19 03:07:03 +07:00
|
|
|
struct extent_map *search_extent_mapping(struct extent_map_tree *tree,
|
|
|
|
u64 start, u64 len);
|
2018-01-06 02:51:11 +07:00
|
|
|
int btrfs_add_extent_mapping(struct extent_map_tree *em_tree,
|
|
|
|
struct extent_map **em_in, u64 start, u64 len);
|
2007-08-28 03:49:44 +07:00
|
|
|
#endif
|