linux_dsm_epyc7002/drivers/mtd/nand/Makefile

69 lines
2.8 KiB
Makefile
Raw Normal View History

#
# linux/drivers/nand/Makefile
#
obj-$(CONFIG_MTD_NAND) += nand.o
obj-$(CONFIG_MTD_NAND_ECC) += nand_ecc.o
obj-$(CONFIG_MTD_NAND_BCH) += nand_bch.o
obj-$(CONFIG_MTD_SM_COMMON) += sm_common.o
obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nand.o
obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o
obj-$(CONFIG_MTD_NAND_DENALI) += denali.o
obj-$(CONFIG_MTD_NAND_DENALI_PCI) += denali_pci.o
obj-$(CONFIG_MTD_NAND_DENALI_DT) += denali_dt.o
obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
obj-$(CONFIG_MTD_NAND_BF5XX) += bf5xx_nand.o
obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o
obj-$(CONFIG_MTD_NAND_TANGO) += tango_nand.o
obj-$(CONFIG_MTD_NAND_DAVINCI) += davinci_nand.o
obj-$(CONFIG_MTD_NAND_DISKONCHIP) += diskonchip.o
obj-$(CONFIG_MTD_NAND_DOCG4) += docg4.o
obj-$(CONFIG_MTD_NAND_FSMC) += fsmc_nand.o
obj-$(CONFIG_MTD_NAND_SHARPSL) += sharpsl.o
obj-$(CONFIG_MTD_NAND_NANDSIM) += nandsim.o
obj-$(CONFIG_MTD_NAND_CS553X) += cs553x_nand.o
obj-$(CONFIG_MTD_NAND_NDFC) += ndfc.o
obj-$(CONFIG_MTD_NAND_ATMEL) += atmel_nand.o
obj-$(CONFIG_MTD_NAND_GPIO) += gpio.o
omap2_nand-objs := omap2.o
obj-$(CONFIG_MTD_NAND_OMAP2) += omap2_nand.o
obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD) += omap_elm.o
obj-$(CONFIG_MTD_NAND_CM_X270) += cmx270_nand.o
obj-$(CONFIG_MTD_NAND_PXA3xx) += pxa3xx_nand.o
obj-$(CONFIG_MTD_NAND_TMIO) += tmio_nand.o
obj-$(CONFIG_MTD_NAND_PLATFORM) += plat_nand.o
obj-$(CONFIG_MTD_NAND_PASEMI) += pasemi_nand.o
obj-$(CONFIG_MTD_NAND_ORION) += orion_nand.o
obj-$(CONFIG_MTD_NAND_OXNAS) += oxnas_nand.o
obj-$(CONFIG_MTD_NAND_FSL_ELBC) += fsl_elbc_nand.o
obj-$(CONFIG_MTD_NAND_FSL_IFC) += fsl_ifc_nand.o
obj-$(CONFIG_MTD_NAND_FSL_UPM) += fsl_upm.o
obj-$(CONFIG_MTD_NAND_SLC_LPC32XX) += lpc32xx_slc.o
obj-$(CONFIG_MTD_NAND_MLC_LPC32XX) += lpc32xx_mlc.o
obj-$(CONFIG_MTD_NAND_SH_FLCTL) += sh_flctl.o
obj-$(CONFIG_MTD_NAND_MXC) += mxc_nand.o
obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o
obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o
obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o
mtd: nand: vf610_nfc: Freescale NFC for VF610, MPC5125 and others This driver supports Freescale NFC (NAND flash controller) found on Vybrid (VF610), MPC5125, MCF54418 and Kinetis K70. The driver has been tested using 8-bit and 16-bit NAND interface on the ARM based Vybrid SoC VF500 and VF610 platform. parameter page reading. Limitations: - Untested on MPC5125 and M54418. - DMA and pipelining not used. - 2K pages or less. - No chip select, one NAND chip per controller. - No hardware ECC. Some paths have been hand-optimized and evaluated by measurements made using mtd_speedtest.ko on a 100MB MTD partition. Colibri VF50 eb write % eb read % page write % page read % rel/opt 5175 11537 4560 11039 opt 5164 -0.21 11420 -1.01 4737 +3.88 10918 -1.10 none 5113 -1.20 11352 -1.60 4490 -1.54 10865 -1.58 Colibri VF61 eb write % eb read % page write % page read % rel/opt 5766 13096 5459 12846 opt 5883 +2.03 13064 -0.24 5561 +1.87 12802 -0.34 none 5701 -1.13 12980 -0.89 5488 +0.53 12735 -0.86 rel = using readl_relaxed/writel_relaxed in optimized paths opt = hand-optimized by combining multiple accesses into one read/write The measurements have not been statistically verfied, hence use them with care. The author came to the conclusion that using the relaxed variants of readl/writel are not worth the additional code. Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com> Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr> Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Alexey Klimov <klimov.linux@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-09-03 08:06:33 +07:00
obj-$(CONFIG_MTD_NAND_VF610_NFC) += vf610_nfc.o
obj-$(CONFIG_MTD_NAND_RICOH) += r852.o
obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
obj-$(CONFIG_MTD_NAND_JZ4780) += jz4780_nand.o jz4780_bch.o
obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/
obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o
obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o
obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o
obj-$(CONFIG_MTD_NAND_BRCMNAND) += brcmnand/
mtd: nand: Qualcomm NAND controller driver The Qualcomm NAND controller is found in SoCs like IPQ806x, MSM7xx, MDM9x15 series. It exists as a sub block inside the IPs EBI2 (External Bus Interface 2) and QPIC (Qualcomm Parallel Interface Controller). These IPs provide a broader interface for external slow peripheral devices such as LCD and NAND/NOR flash memory or SRAM like interfaces. We add support for the NAND controller found within EBI2. For the SoCs of our interest, we only use the NAND controller within EBI2. Therefore, it's safe for us to assume that the NAND controller is a standalone block within the SoC. The controller supports 512B, 2kB, 4kB and 8kB page 8-bit and 16-bit NAND flash devices. It contains a HW ECC block that supports BCH ECC (4, 8 and 16 bit correction/step) and RS ECC(4 bit correction/step) that covers main and spare data. The controller contains an internal 512 byte page buffer to which we read/write via DMA. The EBI2 type NAND controller uses ADM DMA for register read/write and data transfers. The controller performs page reads and writes at a codeword/step level of 512 bytes. It can support up to 2 external chips of different configurations. The driver prepares register read and write configuration descriptors for each codeword, followed by data descriptors to read or write data from the controller's internal buffer. It uses a single ADM DMA channel that we get via dmaengine API. The controller requires 2 ADM CRCIs for command and data flow control. These are passed via DT. The ecc layout used by the controller is syndrome like, but we can't use the standard syndrome ecc ops because of several reasons. First, the amount of data bytes covered by ecc isn't same in each step. Second, writing to free oob space requires us writing to the entire step in which the oob lies. This forces us to create our own ecc ops. One more difference is how the controller accesses the bad block marker. The controller ignores reading the marker when ECC is enabled. ECC needs to be explicity disabled to read or write to the bad block marker. The nand_bbt helpers library hence can't access BBMs for the controller. For now, we skip the creation of BBT and populate chip->block_bad and chip->block_markbad helpers instead. Reviewed-by: Andy Gross <agross@codeaurora.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Archit Taneja <architt@codeaurora.org> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2016-02-03 15:59:50 +07:00
obj-$(CONFIG_MTD_NAND_QCOM) += qcom_nandc.o
obj-$(CONFIG_MTD_NAND_MTK) += mtk_nand.o mtk_ecc.o
nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
nand-objs += nand_amd.o
nand-objs += nand_hynix.o
nand-objs += nand_micron.o
nand-objs += nand_samsung.o
nand-objs += nand_toshiba.o