linux_dsm_epyc7002/sound/hda/Makefile

snd-hda-core-objs := hda_bus_type.o hdac_bus.o hdac_device.o hdac_sysfs.o \
	hdac_regmap.o array.o

snd-hda-core-objs += trace.o
CFLAGS_trace.o := -I$(src)

obj-$(CONFIG_SND_HDA_CORE) += snd-hda-core.o
ALSA: hda - Move generic array helpers to core lib This will be used by the regmap support. Signed-off-by: Takashi Iwai <tiwai@suse.de> 2015-03-03 23:33:10 +07:00			`snd-hda-core-objs := hda_bus_type.o hdac_bus.o hdac_device.o hdac_sysfs.o \`
ALSA: hda - Add regmap support This patch adds an infrastructure to support regmap-based verb accesses. Because o the asymmetric nature of HD-audio verbs, especially the amp verbs, we need to translate the verbs as a sort of pseudo registers to be mapped uniquely in regmap. In this patch, a pseudo register is built from the NID, the AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent to HD-audio bus but without codec address field. OTOH, for writing, the same pseudo register is translated to AC_VERB_SET_* automatically. The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding AC_VERB_GET_AMP_* verb and parameter at writing. Some verbs has a single command for read but multiple for writes. A write for such a verb is split automatically to multiple verbs. The patch provides also a few handy helper functions. They are designed to be accessible even without regmap. When no regmap is set up (e.g. before the codec device instantiation), the direct hardware access is used. Also, it tries to avoid the unnecessary power-up. The power up/down sequence is performed only on demand. The codec driver needs to call snd_hdac_regmap_exit() and snd_hdac_regmap_exit() at probe and remove if it wants the regmap access. There is one flag added to hdac_device. When the flag lazy_cache is set, regmap helper ignores a write for a suspended device and returns as if it was actually written. It reduces the hardware access pretty much, e.g. when adjusting the mixer volume while in idle. This assumes that the driver will sync the cache later at resume properly, so use it carefully. Signed-off-by: Takashi Iwai <tiwai@suse.de> 2015-02-25 20:42:38 +07:00			`hdac_regmap.o array.o`
ALSA: hda - Make snd_hda_bus_type public Define the common hd-audio driver and device types to bind over snd_hda_bus_type publicly. This allows to implement other type of device and driver code over hd-audio bus. Now both struct hda_codec and struct hda_codec_driver inherit these new struct hdac_device and struct hdac_driver, respectively. The bus registration is done in subsys_initcall() to assure it before any other driver registrations. Signed-off-by: Takashi Iwai <tiwai@suse.de> 2015-02-18 03:46:37 +07:00
ALSA: hda - Re-add tracepoints to HD-audio core driver Now let's take the basic tracepoints back to the HD-audio driver. The three bus tracepoints, hda_send_cmd, hda_get_response and hda_unsol_event are revived but in a slightly different form. Since we don't assign the card number there, print the bus device name instead. Signed-off-by: Takashi Iwai <tiwai@suse.de> 2015-03-10 21:16:28 +07:00			`snd-hda-core-objs += trace.o`
			`CFLAGS_trace.o := -I$(src)`

ALSA: hda - Make snd_hda_bus_type public Define the common hd-audio driver and device types to bind over snd_hda_bus_type publicly. This allows to implement other type of device and driver code over hd-audio bus. Now both struct hda_codec and struct hda_codec_driver inherit these new struct hdac_device and struct hdac_driver, respectively. The bus registration is done in subsys_initcall() to assure it before any other driver registrations. Signed-off-by: Takashi Iwai <tiwai@suse.de> 2015-02-18 03:46:37 +07:00			`obj-$(CONFIG_SND_HDA_CORE) += snd-hda-core.o`