linux_dsm_epyc7002/drivers/fsi/Makefile


obj-$(CONFIG_FSI) += fsi-core.o
obj-$(CONFIG_FSI_MASTER_HUB) += fsi-master-hub.o
obj-$(CONFIG_FSI_MASTER_GPIO) += fsi-master-gpio.o
obj-$(CONFIG_FSI_MASTER_AST_CF) += fsi-master-ast-cf.o
obj-$(CONFIG_FSI_SCOM) += fsi-scom.o
obj-$(CONFIG_FSI_SBEFIFO) += fsi-sbefifo.o
drivers/fsi: Add empty fsi bus definitions This change adds the initial (empty) fsi bus definition, and introduces drivers/fsi/. Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Chris Bostic <cbostic@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 2017-02-01 23:53:41 +07:00
			`obj-$(CONFIG_FSI) += fsi-core.o`
drivers/fsi: Add hub master support Add an engine driver to expose a "hub" FSI master - which has a set of control registers in the engine address space, and uses a chunk of the slave address space for actual FSI communication. Additional changes from Jeremy Kerr <jk@ozlabs.org>. Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 2017-06-07 04:08:57 +07:00			`obj-$(CONFIG_FSI_MASTER_HUB) += fsi-master-hub.o`
drivers/fsi: Add GPIO based FSI master Implement a FSI master using GPIO. Will generate FSI protocol for read and write commands to particular addresses. Sends master command and waits for and decodes a slave response. Includes changes from Edward A. James <eajames@us.ibm.com> and Jeremy Kerr <jk@ozlabs.org>. Signed-off-by: Edward A. James <eajames@us.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 2017-06-07 04:08:54 +07:00			`obj-$(CONFIG_FSI_MASTER_GPIO) += fsi-master-gpio.o`
fsi: master-ast-cf: Add new FSI master using Aspeed ColdFire The Aspeed AST2x00 can contain a ColdFire v1 coprocessor which is currently unused on OpenPower systems. This adds an alternative to the fsi-master-gpio driver that uses that coprocessor instead of bit banging from the ARM core itself. The end result is about 4 times faster. The firmware for the coprocessor and its source code can be found at https://github.com/ozbenh/cf-fsi and is system specific. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> 2018-06-12 06:55:04 +07:00			`obj-$(CONFIG_FSI_MASTER_AST_CF) += fsi-master-ast-cf.o`
drivers/fsi: Add SCOM FSI client device driver Create a simple SCOM engine device driver that reads and writes its control registers via an FSI bus. Includes changes from Edward A. James <eajames@us.ibm.com>. Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Edward A. James <eajames@us.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 2017-06-07 04:08:56 +07:00			`obj-$(CONFIG_FSI_SCOM) += fsi-scom.o`
fsi/sbefifo: Add driver for the SBE FIFO This driver provides an in-kernel and a user API for accessing the command FIFO of the SBE (Self Boot Engine) of the POWER9 processor, via the FSI bus. It provides an in-kernel interface to submit command and receive responses, along with a helper to locate and analyse the response status block. It's a simple synchronous submit() type API. The user interface uses the write/read interface that an earlier version of this driver already provided, however it has some specific limitations in order to keep the driver simple and avoid using up a lot of kernel memory: - The user should perform a single write() with the command and a single read() to get the response (with a buffer big enough to hold the entire response). - On a write() the command is simply "stored" into a kernel buffer, it is submitted as one operation on the subsequent read(). This allows to have the code write directly from the FIFO into the user buffer and avoid hogging the SBE between the write() and read() syscall as it's critical that the SBE be freed asap to respond to the host. An extra write() will simply replace the previously written command. - A write of a single 4 bytes containing the value 0x52534554 in big endian will trigger a reset request. No read is necessary, the write() call will return when the reset has been acknowledged or times out. - The command is limited to 4K bytes. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Joel Stanley <joel@jms.id.au> --- 2018-05-17 12:58:00 +07:00			`obj-$(CONFIG_FSI_SBEFIFO) += fsi-sbefifo.o`