mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-23 11:06:48 +07:00
85 lines
2.8 KiB
Plaintext
85 lines
2.8 KiB
Plaintext
|
Kernel driver ltc2945
|
||
|
|
=====================
|
||
|
|
|
||
|
|
Supported chips:
|
||
|
|
* Linear Technology LTC2945
|
||
|
|
Prefix: 'ltc2945'
|
||
|
|
Addresses scanned: -
|
||
|
|
Datasheet:
|
||
|
|
http://cds.linear.com/docs/en/datasheet/2945fa.pdf
|
||
|
|
|
||
|
|
Author: Guenter Roeck <linux@roeck-us.net>
|
||
|
|
|
||
|
|
|
||
|
|
Description
|
||
|
|
-----------
|
||
|
|
|
||
|
|
The LTC2945 is a rail-to-rail system monitor that measures current, voltage,
|
||
|
|
and power consumption.
|
||
|
|
|
||
|
|
|
||
|
|
Usage Notes
|
||
|
|
-----------
|
||
|
|
|
||
|
|
This driver does not probe for LTC2945 devices, since there is no register
|
||
|
|
which can be safely used to identify the chip. You will have to instantiate
|
||
|
|
the devices explicitly.
|
||
|
|
|
||
|
|
Example: the following will load the driver for an LTC2945 at address 0x10
|
||
|
|
on I2C bus #1:
|
||
|
|
$ modprobe ltc2945
|
||
|
|
$ echo ltc2945 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
|
||
|
|
|
||
|
|
|
||
|
|
Sysfs entries
|
||
|
|
-------------
|
||
|
|
|
||
|
|
Voltage readings provided by this driver are reported as obtained from the ADC
|
||
|
|
registers. If a set of voltage divider resistors is installed, calculate the
|
||
|
|
real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
|
||
|
|
value of the divider resistor against the measured voltage and R2 is the value
|
||
|
|
of the divider resistor against Ground.
|
||
|
|
|
||
|
|
Current reading provided by this driver is reported as obtained from the ADC
|
||
|
|
Current Sense register. The reported value assumes that a 1 mOhm sense resistor
|
||
|
|
is installed. If a different sense resistor is installed, calculate the real
|
||
|
|
current by dividing the reported value by the sense resistor value in mOhm.
|
||
|
|
|
||
|
|
in1_input VIN voltage (mV). Voltage is measured either at
|
||
|
|
SENSE+ or VDD pin depending on chip configuration.
|
||
|
|
in1_min Undervoltage threshold
|
||
|
|
in1_max Overvoltage threshold
|
||
|
|
in1_lowest Lowest measured voltage
|
||
|
|
in1_highest Highest measured voltage
|
||
|
|
in1_reset_history Write 1 to reset in1 history
|
||
|
|
in1_min_alarm Undervoltage alarm
|
||
|
|
in1_max_alarm Overvoltage alarm
|
||
|
|
|
||
|
|
in2_input ADIN voltage (mV)
|
||
|
|
in2_min Undervoltage threshold
|
||
|
|
in2_max Overvoltage threshold
|
||
|
|
in2_lowest Lowest measured voltage
|
||
|
|
in2_highest Highest measured voltage
|
||
|
|
in2_reset_history Write 1 to reset in2 history
|
||
|
|
in2_min_alarm Undervoltage alarm
|
||
|
|
in2_max_alarm Overvoltage alarm
|
||
|
|
|
||
|
|
curr1_input SENSE current (mA)
|
||
|
|
curr1_min Undercurrent threshold
|
||
|
|
curr1_max Overcurrent threshold
|
||
|
|
curr1_lowest Lowest measured current
|
||
|
|
curr1_highest Highest measured current
|
||
|
|
curr1_reset_history Write 1 to reset curr1 history
|
||
|
|
curr1_min_alarm Undercurrent alarm
|
||
|
|
curr1_max_alarm Overcurrent alarm
|
||
|
|
|
||
|
|
power1_input Power (in uW). Power is calculated based on SENSE+/VDD
|
||
|
|
voltage or ADIN voltage depending on chip configuration.
|
||
|
|
power1_min Low lower threshold
|
||
|
|
power1_max High power threshold
|
||
|
|
power1_input_lowest Historical minimum power use
|
||
|
|
power1_input_highest Historical maximum power use
|
||
|
|
power1_reset_history Write 1 to reset power1 history
|
||
|
|
power1_min_alarm Low power alarm
|
||
|
|
power1_max_alarm High power alarm
|